Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for U-Reach SuperB USB3.1
Summary of Contents for U-Reach SuperB USB3.1
- Page 1 USB3.1 SuperB Flash Duplicator & Tester (USB/USB-HDD) User Manual v A.01...
-
Page 2: Table Of Contents
v A.01.1 Index Product Disclaimer ......................... 3 Warranty ..........................3 Piracy Statement ........................3 Before You Start ........................4 Notice Symbols ........................4 Introduction ..........................5 Function Table ......................... 7 Function Description ......................10 1. Copy ............................ 10 2. Compare ..........................11 3. -
Page 3: Product Disclaimer
Product Disclaimer The manufacturer is not accountable for any incidental or consequential damages, including, but not limited to property harm, loss of time or data from use of any our product, or any other damages attributable to product malfunction or failure of including without limitation, those attributed to reliance of the materials provided, costs of product replacement, loss of use, data or profits, delays or business interruptions, any principle of legal responsibility arising from or in reference to the use, overall performance, delays in... -
Page 4: Before You Start
⚫ Using the Copy+Compare function provides the most flawless duplication. ⚫ Damage incurred due to noncompliance with U-Reach operating instructions will void ⚫ the warranty. Store the equipment safely when not in use and keep out of the reach of children. -
Page 5: Introduction
Introduction 1. Features The duplicator was designed with diversified media compatibility and high-speed performance in mind to not only flawlessly duplicate in high speed demands, but also provides helpful examinations by delivering the most accurate testing functions known today. The user-friendly interface offers stress-free operation with no steep learning curve to climb. - Page 6 2. Package Contents Duplicator x1 Power Cord x 1 User Manual x 1 1 pair of Gloves* *Wear protective gloves to prevent burns when handling devices. 3. Hardware Overview Control Buttons LCD Display First Port is Source Port LED Indicator: Green: Pass Red: Fail Power Switch...
-
Page 7: Function Table
Function Table *Below functions and features subject to change without notice. Function Description 1. Copy Data or whole media duplication only. Bit-for-bit comparison between the source and target flash 2. Compare medias. First copies, then compares the target to the source once 3. - Page 8 6.3.3 H6 Safe RW Checks the flash’s quality by writing and reading its empty space. This function will not change the flash’s content or format. 6.3.4 Setup Range % Sets the flash’s checking range percentage. 6.3.5 Setup Range MB Sets the flash’s checking range in MB. 6.3.6 Set Error Limit Sets the error tolerance range when checking the flash.
- Page 9 7.5 Check USB Signal Before Do Check Copy Allow user to check the 2.0 / 3.0 Do NOT Check signal before copy or not. 7.6 Target Tolerance No Limit Sets the capacity tolerance range 100% Same between the source and target. Allow Tolerance The default setting is “No limit”.
-
Page 10: Function Description
Function Description 1. Copy Step 1: Prepare source and target devices. Recommendation: Target device(s)’ capacity must be equal to or larger Note than the source device capacity. Step 2: Connect source and target devices. Step 3: Proceed to copy. Scroll to select "1. Copy", then press "OK" to start the duplication process. The number of working/connected targets will be displayed on LCD. -
Page 11: Compare
If flash card is removed during copy process, the system will stop ⚫ immediately, and red light will illuminate to notify user the copy has failed. Removing the flash card during copy is strongly discouraged as Note it will damage the flash card. Backup the data on target flash cards before starting the copying ⚫... -
Page 12: Information
To protect source data, the system will not run a Capacity Check on ⚫ the master device. When the red error light illuminates, you can use the ▲▼to view ⚫ error information. 5. Information 5.1 USB Info. This setting displays the flash media’s basic information such as file format, content size, and total capacity. - Page 13 The source port will not perform any formatting because this function will Note delete the flash media’s data. 6.1.1 Auto Format This function formats flash into FAT. Plug in the flash media and press "OK". The system will automatically detect its capacity, then format the media per its capacity. ⚫...
- Page 14 ➊ Plug flash media into the slot, select function [6.2 Measure Speed], then press "OK" to start this function. USB3.1 Duplicator [#02] Read: 14.7MB 6.2 Measure Speed Write: 7.0MB ➋ Use the▲▼keys to view the exact "Read" and "Write" flash media speed on each port. To protect source data, the system will not execute “Measure Speed”...
- Page 15 6.3.2 H5 RW This function performs a read and write test to determine the flash’s quality. The flash’s original data will be erased during this test. Use the ▲▼buttons to view the status of each port. Pass Quantity Bad Sector Test Capacity Pass: 1 H5 Test...
- Page 16 6.3.5 Setup Range MB This function sets the quality check capacity range in MB. Use the▲▼buttons to set the range from 1MB to 9000MB. [Setup Range MB] 2000MB The duplicator will abide by whichever was set last if both Range% and Note Range MB are set.
- Page 17 Completely erases the entire flash media, including format and content. This task takes longer. Pressing <ESC> during this process will abandon the task, but the original format and content will no longer be readable. USB3.1 Duplicator Do ERASE ALL 6.5 Full Erase Confirm? 6.6 DoD Erase DoD Erase complies with the U.S.A.
-
Page 18: Setup
The firmware update process may take longer than 5 minutes. Please do not disrupt power or process during BIOS update. If interrupted, the Caution system will become useless. U-Reach will not be held responsible for any damages. 6.8 Calc. CRC64 This function will count the Checksum value for the source port. - Page 19 If the file format is not recognized, the whole flash card, including empty Note space, will be copied even if you specify copy area in “System and Files”. ➋ Whole Media The system will copy the whole flash card, including empty space and format. This function is useful when users want to copy the whole flash or have a flash source with an unknown format.
- Page 20 7.5 Check USB Signal Before Copy Allow user to check the USB2.0/3.0 signal before copy or not. Do not Check Do Check 7.6 Target Tolerance This function sets the capacities tolerance range between the source and target flash. If the capacity is outside the tolerance range, the copy will fail.
- Page 21 Note The buffer memory may vary depending on product model. 7.8 Power Off Time Between Copy+Compare The use of this setting is highly advised as it prevents data loss due to unstable flash. Users can set the time gap of power supply between copy and compare. The time gap can be set from 0 to 15 seconds.
- Page 22 [Monitor Device After Copy] Total OK: 10 NG: 0 Do NOT Check 12:48 OK: 10 NG: 10 In this case, if set at “Do Check”, the copied device will power off automatically after Copy job completes and the LCD will back to the previous job. [Monitor Device After Copy] 1.
-
Page 23: Specification
Specification USB3.1 Duplicator Capacity Designed support capability over 18TB+ Stand-alone, FPGA-based operation (Non-PC Operation Type based) Specifications Supported Languages English or Japanese LCD Display Backlit Monochrome LCD Display LEDs 2 LED Indicators per Port (1 Red/ 1 Green) 4 Push Buttons (▲, ▼, OK, ESC) Control Panel Quick Copy (Systems &...
Need help?
Do you have a question about the SuperB USB3.1 and is the answer not in the manual?
Questions and answers