Related Manuals for U-Reach V5.30
Summary of Contents for U-Reach V5.30
- Page 1 DVD/Blu-ray Duplicator User Guide V5.30 www.ureach-inc.com the Expert of Duplicators...
-
Page 2: Table Of Contents
Content Index Chapter 1. Basic Introduction 9-8. Format HDD 9-9. Load & Copy 1. Features 2. System Overview Chapter 3. Specification 2-1. Package Content 2-2. Other components necessary for Chapter 4. Appendix assembling the Duplicator Lightscribe Operation 2-3. SATA controller hardware Installation guide Error Message Chapter 2. -
Page 3: Chapter 1. Basic Introduction
Chapter 1. Basic Introduction 1. Features ● No PC needed. Independent SATA to SATA DVD / Blu-ray Disc Duplication. ● Sepcial Ssynchronous Load and Copy technology. When the system was installed with HDD, the system will load master source disc to HDD while copying disc to disc. -
Page 4: System Overview
Chapter 1. Basic Introduction 2. System Overview 2-1. Package Content Controller SATA Cables(180˚) User Manual 2-2. Other components necessary for assembling the Duplicators CD/DVD-ROM CD/DVD-RW Writer User Manual... -
Page 5: Sata Controller Hardware Installation
Chapter 1. Basic Introduction 2-3. SATA Controller Hardware Installation Cuide Example: 1-4 installed 1.(ROM) Write 1 Write 2 Write 3 Write 4 Write 5 Example: 1-7 installed 1.HDD (Master) ROM (Slave) Write 1 Write 2 Write 3 Write 4 Write 5 Write 6 Write 7 Write 8... - Page 6 Chapter 1. Basic Introduction Example: 1-11 installed 1.HDD (Master) ROM (Slave) Write 1 Write 2 Write 3 Write 4 Write 5 Write 6 Write 7 Write 8 Write 9 Write 10 Write 11 Write 12...
-
Page 7: Chapter 2. Function Operation
Chapter 2. Function Operation Function Table-CD/DVD/BD Duplication Function Sub-function Description 1. Copy To copy disc to disc or copy disc from HDD. 2. Test To simulate copy process 3. Compare To bit by bit compare between source disc and copied discs To copy first and compare the copied discs later. -
Page 8: Chapter 2. Function Operation
Chapter 2. Function Operation Allow the system to do the Copy, Test, Compare and Copy + Compare 1. Auto Start Time functions automatically 1. Basic 2. Display Mode 2. Show Timer 3. Show Speed 3. Button Beep 1. Eject All Discs To eject all trays with disc inside once the system is booted up. -
Page 9: Copy
Chapter 2. Function Operation 1. Copy It is important to make sure that your source disc is placed in the right drive. You can check or select your source reader by 6.Select Source. (plase refer to 6.Select Source, page 11) 1. -
Page 10: Test
Chapter 2. Function Operation 2. Test This function will simulate the copy process to ensure error free duplication. During the simulation, it will be nothing left in the recordable discs. 1. Using to select 2.Test and press 2. Press to start test 3. -
Page 11: Copy + Compare
Chapter 2. Function Operation 3. The system will detect the source and target discs automatically. 4. After detecting, the system will start to compare. 5. When the comparison has finished, the system will show the compare result. 4. Copy + Compare This function will to do copy task first and execute comparison automatically when copy process has been finished. -
Page 12: Set Burn Speed
Chapter 2. Function Operation 5. Set Burn Speed You can adjust the burning speed of CD/Audio CD/DVD/DVD DL/Blu-ray by this setting. The default setting of CD is 40X, Audio CD 24X, DVD 8X, DVD DL 2X and Blu-ray 2X. 1. Using to select 5.Set Burn Speed and press 2. -
Page 13: Utility
Chapter 2. Function Operation 7. Utility 7-1. Information You can check the information of disc, drive and system by this function. By pressing each disc or drive’s information will show on the LCD. 1. Using to select 7.Utility, press to enter the sub menu. Then, select 1.Information and press 2. -
Page 14: Erase Disc
Chapter 2. Function Operation ● System Info.: The model No. and firmware version can be checked here. 7-2. Erase Disc This function will erase the rewritable discs in WRITER tray, there are two erase modes available: ● Quick Erase: It will erase the INDEX of the rewritable disc. ●... -
Page 15: Prescan Source
Chapter 2. Function Operation 6. Once the erase task has finished, the O stop blinking, the disc will be ejected automatically. **Note: 1 If you see F and f are blinking by turns, which means the whole new DVD+RW is in format process. -
Page 16: Track Edit
Chapter 2. Function Operation 7-4. Track Edit This function enables you to combine audio tracks from various CDs into a single customize audio CD. ● Copy Track: You can select and combine audio tracks from different CDs in this section. ●... -
Page 17: Update Bios
Chapter 2. Function Operation 7-7. Update BIOS You can update the system’s firmware in this function. 1. Place manufacturer certified update file CD into any drive 2. Pressing to select 7.Utility and sub menu 7.Update BIOS and then press start the process. 3. -
Page 18: Setup
Chapter 2. Function Operation 8. Setup 8-1. Auto Start Time This setting will allow the system to do the Copy, Test, Compare and Copy + Compare functions automatically in a few seconds once the source and blank discs are placed in the trays and detected by the system. -
Page 19: Button Beep
Chapter 2. Function Operation 8-3. Button Beep This setting will allow you to set up to hear a beep when a button is pressed or not. 8-4. Eject On Start You can make the trays or discs eject once the system is booted up. ●... - Page 20 Chapter 2. Function Operation **Note: Skip Read Error can not fix the error in the source disc, all it does is skipping the errors and keeps copying the rest of readable data. ● Change Bad Master: This setting will make the system eject source disc and ask for another one while the source disc is unreadable for system.
-
Page 21: Hdd Manager (For Hdd-Installed Duplicator)
Chapter 2. Function Operation 9. HDD Manager (For HDD-installed duplicator) 9-1. Select Image You can select image file from HDD as your source for copy. When this function is selected, the system will set the HDD to be the source reader automatically. 1. -
Page 22: Set Reader Speed
Chapter 2. Function Operation 4. When loading has finished, the disc will be ejected automatically. **Note: The source disc can be placed in any drive, it will not affect the loading process. 9-3. Set Reader Speed You can adjust the reading speed of the drive which you put the source disc. This function is ONLY available when you loading the source disc to HDD. -
Page 23: Delete Image
Chapter 2. Function Operation 1. Pressing to select 9.HDD Manager and sub menu 5.Rename Image. 2. Pressing and select which image file you would like to rename by pressing and then press to start edit a new name for the selected file. You can select characters or number by pressing , and press to the next space... -
Page 24: Format Hdd
Chapter 2. Function Operation 9-8. Format HDD This function allows you to format the built-in HDD while the HDD is NOT selected as reading source. You can change the source from HDD to other drive in 6.Select Source, page 11. Due to the capacity for discs loading is hard to predict precisely and more and more different discs coming out. -
Page 25: Chapter 3. Specification
Chapter 3. Specification Model P501D P504D P507U/W P511U/W P515X Target Buffer (DDR2) 64MB 128MB(U) / 512MB(W) 256MB Interface SATA CD Speed DVD Speed Blu-ray Speed Writing Method DAO, TAO, RAW BD-ROM, BD-R, BD-RE DVD-ROM, DVD-Video, DVD-Audio, DVD+R, DVD+RW, DVD-R, DVD-RW, Dual Layer DVD±R, Disc Format Support CD-ROM, CD-RW, CD-I, Audio CD, Video CD, CD+G, CD-TEXT,... -
Page 26: Chapter 4. Appendix
Chapter 4. Appendix Lightscribe Operation Step 1 Install Lightscribe template software to PC Download LightScribe software from www.lightscribe.com and install below software. A. LIGHTSCRIBE SYSTEM SOFTWARE (LSS) B. LIGHTSCRIBE TEMPLATE LABELER. - Page 27 Chapter 4. Appendix Step 2 Execute "LightScribe Drive select.exe".exe file to select LightScribe Drives 1. Receive a .exe file from your supplier. 2. Execute the .exe file on your PC. 3. And select the LightScribe Duplicator drive on the list. **Note: When everytime the Duplicator change LightScribe drive, must re-select drive before create LightScribe image for that Duplicator.
- Page 28 Chapter 4. Appendix Step 3 Design Lightscribe Template and Lightscribe printing on PC. 1. Click to launch the LightScribe Template on our PC. 2. Follow procedure to create your label image. 3. Make sure the lightscribe drive is selected. **Note: If Lightscribe template can not be executed normally under Window7, please try to click right button on the mouse on the Lightscribe icon and select "...
- Page 29 Chapter 4. Appendix 5. Plug the USB drive or Disc into Duplicator. 6. Select the utility function 7-8.PRINT LS Label. The system will read the image into the duplicator and start printing the lightscribe label. Data side Print side **Note: When doing the lightscribe printing, please turn over the disc.
-
Page 30: Error Message
Chapter 4. Appendix Error Message Error Message Possible Reasons Toubleshooting Master disc is empty or protected. Bad Master Disc Please check your master disc by (1) Disc Info (2) by PC. Master disc has demaged or bad quality Warning: You put different format of blank disc from the master disc. Please check your master and blank disc foramt by "...
Need help?
Do you have a question about the V5.30 and is the answer not in the manual?
Questions and answers