Related Manuals for U-Reach Silver Fox PRO
Summary of Contents for U-Reach Silver Fox PRO
- Page 1 USB 3.0 Duplicator User Guide V 2.0 The Data Equipment Expert • Duplication/Inspection/Sanitization...
-
Page 3: Table Of Contents
4.5.6 Power Off Time Between 4. Power Adapter Copy&Compare 4.5.7 Auto Start After Fill Device Function Table 4.5.8 Language Silver Fox Pro Series 4.5.9 Select Speed 4.5.10 Set HDD Mode Operation Guide 4.5.11 Advanced Setup 1. How to Copy 2. How to Prevent from Failed Duplication 3. - Page 4 Disclaimer of Warranties Disclaimer of Warranties All duplicators are made specifically for data backup with legal authorities from copyright owners. Any unauthorized action of copyright is strictly prohibited, and the original manufacturer disclaims all warranties or representations of illegal actions by users. The original manufacturer also disclaims any liability for any loss or damage due to not being able to perform its undertakings or provide any of the services attributed to any events or circumstances beyond our control.
- Page 5 Before You Start Definition Flash/ Flash media/ Media Flash media including SD/microSD memory card, Compact flash card, USB drive and USB- HDD. Capacity The maximum data amount that can be contained in USB drive or USB-HDD. Total capacity Socket A mechanical construction used to connect two applications. USB裝置拷貝機...
-
Page 6: Features
Introduction 1. Features Silver Fox Pro series provide USB3.0 ultra high speed duplication, specialized for external USB-HDD usage. The series support USB3.0 drive, USB3.0-HDD of high-volume, high- capacity duplication. Each USB port is independent from each other. The series support ultra high transmission speed, real test up to 2.5GB per min for each port and up to... -
Page 7: Hardware Overview
1 Introduction 3. Hardware Overview Control Button OK : Confirm ▲ : Backward Source port ESC : Escape Red: Operation fails Green: Operation Succeeds Front Side Power switch Power supply(12V 12.5A) USB socket for PC-Link Back Side... -
Page 8: Power Adapter
1 Introduction 4. Power Adapter Each model may need different power adapters according to its need. The table below is the adapter supplying situation for each series. Adapter volume needed Adapter volume needed when Port Adapter when copying USB copying USB HDD 12V 12.5A 12V 12.5A 12V 12.5A... -
Page 9: Silver Fox Pro Series
2 Function Table Function Table Silver Fox Pro Series Function Description To make a copy first and then compare the copied flash media with the source immedi- 1.Copy&Compare ately after the copy has finished. Bit-for-Bit comparison between the source and all other copied flash medias. - Page 10 2 Function Table 4.4.4 Quick Erase To erase the content of flash media. It will keep the FAT format. 4.4.5 Full Erase To completely bit for bit erase data of flash including format and content, but it takes more time. 4.4 Utility 4.4.6 System Update System firmware updating via the flash media.
- Page 11 3 Operation Guide Operation Guide 1. How to Copy 1.1 Steps to Make Mass Copy Step 1 Plug-in the flash source. Step 2 Plug-in the flash targets. Step 3 The LCD will show the number of flash targets which are ready to copy. Step 4 Press "OK"...
- Page 12 3 Operation Guide Note: ❶ LED Light indication a) When copy is processing, the green LED will flash. When the copy is finished, the green LED will stop Green Light flashing but will remain illuminated. b) If an error occurs, the red LED will illuminate. Red Light ❷...
- Page 13 3 Operation Guide 1.2 The Setting Related to Copy Result There are several sub-functions related to the results of copy, users could adjust them in function "4.5 Setup" to meet the needs before copy. 1.2.1. Copy Area Settings (Function4.5.1) a. Copy Area : System and Files It is also called "Quick Copy"...
-
Page 14: How To Prevent From Failed Duplication
3 Operation Guide 1.2.3. Asynchronous Settings (Function4.5.4) The conditions of executing Users can select "Disable" to close Asynchronous copy or "Enable" to activate the function. If the "Asynchronous Copy" setup is "Enable", and the data in source is smaller than system's buffer memory, it will automatically use asynchronous mode to do copy. -
Page 15: How To Ensure Duplication As Correct
3 Operation Guide (2) Suitable Data & Settings a) Target Tolerance Settings Go to Function "4.5.3 Target Tolerance" to check if the setting of capacity difference range between source and target is right. b) Capacity of the Data in Source Make sure that the data of source is within the capacity of target. -
Page 16: How To Check Flash Device
3 Operation Guide 4. How to Check Flash Device The series flash duplicator is not only made for duplicating but also has powerful flash device diagnostic tools to detect flash's quality and check real capacity and speed. It is very important to own high-quality flash devices, and the flash duplicator can help users to achieve this goal. - Page 17 3 Operation Guide Note: ❶ This function can support asynchronous operation. Users can continuously plug flash media in and out without pushing any buttons. ❷ "Capacity Check" function may change or delete the content and format of flash media, please do not execute this function if there is important data in it.
- Page 18 3 Operation Guide (2)Make the related setting of "Media Check" a) Function "4.2.4 Setup Range %" When making quality check, users can set the checking range from 1% to 100% before executing checking mode. b) Function "4.2.5 Setup Range MB" When making quality check, users can set the checking range from 1MB~9000MB before executing checking mode.
-
Page 19: Function Overview
4 Function Overview Function Overview 1. Copy&Compare This function provides a more convenient selection. Instead of going to function "2.Compare" and pressing "OK" again after copying, function, "1.Copy&Compare" will automatically run the compare function after finishing copying to make sure if the copied result is correct. Before executing this function, users can go to "4.5.Setup"... -
Page 20: Dod Erase
4 Function Overview 3 DoD Erase DoD Erase is an erasing method that complies with the U.S.A. Department of Defense (DoD 5220) standard. It can guarantee the data was fully deleted by erasing the flash three times. Note: ❶ It will damage the data in flash, please make sure you have backup all important data before using this function. ❷... -
Page 21: Setup Range
4 Function Overview 4.2 Media Check ❶ The function is to analyze flash’s quality. There are 3 methods to do media check, "4.2.1 H3 Safe", "4.2.2 H5 RW" and "4.2.3 H6 SafeRW 100%". Before executing quality check, user can go to function "4.2.4/4.2.5 Setup Range","4.2.6 Setup ErrorLimit" and "4.2.9 Set Capacity Limit"... -
Page 22: Setup Range Mb
4 Function Overview 4.2.3 H6 SafeRW 100% This function is used to check the flash's quality by writing and reading data on the empty space of flash media. Select "4.2.3 H6 SafeRW" and press "OK" to start executing this ▲▼ function. -
Page 23: Minimum Read Speed
4 Function Overview 4.2.7 Minimum Read Speed This function can be used to select the flash media whose reading speed is too low. Users can set an expected minimum reading speed first when doing media check, and the flash media which doesn’t reach the minimum speed value will be picked out. Use ▲▼... -
Page 24: Usb Info
4 Function Overview 4.3 Information 4.3.1 USB Info. This function will show the flash media’s basic information such as file format, content size, and total capacity. ▲▼ Press buttons to check the information of each flash media including the source. Port number Total capacity File Format... -
Page 25: Fat16 Format
4 Function Overview Note: The source port (port#1) will not execute any formatting because this function will delete the data of the flash media. 4.4.1.2 FAT16 Format Press "OK" to format any flash media to FAT16 format. 4.4.1.3 FAT32 Format Press "OK"... -
Page 26: Quick Erase
4 Function Overview Note: ❶ This function supports asynchronous operation, you can continuously plug in and pull out flash media without pushing any buttons. ❷ The function may change the content of data and format of flash. ❸ To protect source data, the system will not do Capacity Check on the master device. ❹... -
Page 27: System Update
4 Function Overview 4.4.6 System Update This is to update the system’s firmware version. Please save an un-zipped update file to your flash media and don’t put it in a folder. ❶ Select function 4.4.6 System Update, and press "OK", it will automatically start system updating. -
Page 28: A2 Fake Picker
4 Function Overview 4.4.8 A2 Fake Picker To checks the capacity of each USB device if it is as it’s claimed. A2 failure means the real capacity is different from its claim. ❶ Insert the flash card in any port of duplicator; choose function "4.4.8 A2 Fake Picker", and then press "OK". -
Page 29: Target Tolerance
4 Function Overview 4.5.3 Target Tolerance To set the tolerance % of capacity difference between the source and target. There are three models of settings as below, and the default setting is "No limit". ◦ Allow Tolerance Under this model, users can set the up and low limit of tolerance % of capacity difference separately between the source and target. -
Page 30: Check Before Copy
4 Function Overview 4.5.5 Check Before Copy You can select "Do Check" if you would like to check whether the flash media is workable before copying. 4.5.6 Power Off Time Between Copy&Compare This setting is to prevent from any data loss because of unstable flash, we strongly recommend you to enter this function to set the time gap of power supply between copy and compare. - Page 31 PC has more powerful CPU, but it will has difficulty to handle too many flash medias to copy simultaneously. ❷ No risk of virus infection: U-Reach flash duplicator is an embedded system, it only copies whatever is on the source. When the system is turned off, nothing will be left in the system.
- Page 32 5 FAQ Q5: Why is the copy speed so slow? Our flash duplicator can reach 1.5GB/m for USB/SD/CF series, 2.5GB/min for Silver Fox Series and 3.9GB/m for CF series. If you find the copy speed is slow, it may be affected by flash quality.
- Page 33 5 FAQ ❷ If source capacity is LARGER than the target, for example 2GB copy to 1GB: ▶ There are two results as shown in illustrations (1) and (2) 2.1 When a content is within the target flash media’s capacity Copy OK Because the data is within the 1GB area.
- Page 34 5 FAQ Maintenance Guide Steps to replace socket 1. Turn off the power Attention: For you safety, please turn off the power before replacing the socket or doing any inspection. ➡ Power on Power off 2. Prepare a flat screwdriver, or use your hand to take off the screw of cover.
- Page 35 5 FAQ 3. Take off the cover of socket. 4. Replace a damage socket with a new one. 5. Screw up the cover.
- Page 36 6 Specification USB Drive/USB-HDD Duplicator Buffer 256MB 2.5GB/min Maximum Speed Up to 2TB Capacity Operation Stand-alone operation Compatibility USB drive/USB-HDD/USB3.0/USB2.0/USB1.1 Power supply: 12V 12.5A Power Adapter volume: 1~6 Individual LED (Green/Red) on each slot 4 push buttons Keys ( ▲ /backward, ▼ /forward, OK/confirm, ESC/exit) Humidity Range Working humidity: 20%~80%;...
Need help?
Do you have a question about the Silver Fox PRO and is the answer not in the manual?
Questions and answers