Advertisement
Assembly Instructions
Assembly Instructions
Important
Before you begin, read and comply with all safety and operating instructions,
and ensure all parts and correct quantities are included.
Any parts damaged during shipment must be reported within 5 days of receipt. To
report information regarding missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
www.spectrumfurniture.com
800-235-1262, 715-723-6750
Thank you for purchasing Spectrum products!
(1) 0152133
44"W x 30"D
Worksurface w/ support
(1) 052547 - Right Leg
(1) 052544 - Left Leg
(2) 026011
1/4-20 x 2" FHMS
(4) 026064
1/4-20 x 5/8" PHMS
(1) 0167153
Unit-to-unit bracket
(1) 036281
Dual unit-to-unit
bracket
1
Attach legs to worksurface
1. Place the worksurface face-down onto a non-abrasive surface.
2. Align the legs with the mounting holes, and install (2) #14 x 1-3/4"
PHSM screws into each leg but do not tighten completely yet.
Figure 1.
(1) 052469
Chair rail
(1) 052468
44" Cord channel /
Modesty panel
(4) 0101381
#14 x 1-3/4" PHSM
(4) 0101382
#14 x 7/8" PHSM
(4) 037779
5/16-18 x 1"
Glide
(1) 025069
Glide wrench
The side of the leg with
the threaded hole should
be on the flip-top side
Esports Evolution Desk (44"W)
22860
X2
Assembly tip: Do not tighten component
fasteners completely until all have been
installed. Keeping them loose will help with
alignment between parts during assembly.
#14 x 1-3/4" PHSM
(2 per leg)
Right
leg
Flip-top
Left
leg
Figure 1
0191978R2 Page 1 of 4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Spectrum Industries 22860
Summary of Contents for Spectrum Industries 22860
- Page 1 Thank you for purchasing Spectrum products! (1) 0152133 (1) 052469 44”W x 30”D Chair rail Worksurface w/ support Esports Evolution Desk (44”W) 22860 (1) 052547 - Right Leg (1) 052468 (1) 052544 - Left Leg 44” Cord channel / Modesty panel (2) 026011 (4) 0101381 1/4-20 x 2”...
- Page 2 Install cord channel / modesty panel and glides 1. Orient the modesty panel/cord channel as shown and attach to the legs with (4) 1/4-20 x 5/8” PHM screws. Figure 2.1. 2. Install the (4) glides to the bottom of the legs. The glides can be Glides adjusted later to keep the desk level on uneven surfaces.
- Page 3 Attach chair rail 1. Carefully flip the desk upright-this will require at least two people. 2. Attach the chair rail with (2) 1/4-20 x 2” FHM screws as shown. Note the chair rail should extend above the worksurface, and the countersunk holes should be on the outside.
- Page 4 For a listing of all product specifi c warranty terms please visit our website at: https://www.spectrumfurniture.com/en/resources/purchasing-terms-warranty 1-800-235-1262 Toll-free HELPLINE spectrum@spectrumfurniture.com 1500 RIVER STREET, PO BOX 400, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM © 2021 Spectrum Industries Inc., All rights reserved. 0191978R2 Page 4 of 4...
Need help?
Do you have a question about the 22860 and is the answer not in the manual?
Questions and answers