Spectrum Industries 38979 Owner's Manual
  1. Manuals
  2. Brands
  3. Spectrum Industries Manuals
  4. Indoor Furnishing
  5. 38979
  6. Owner's manual

Spectrum Industries 38979 Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Owner's Manual
Flex Insight Desk
38979
36"W x 24"D Single desk
Important
Before using this product:
• Read this manual
• Comply with all safety and operating instructions
• Ensure all parts and correct quantities are included
Any parts damaged during shipment must be reported
within 5 days of receipt. To report information regarding
missing parts or damage, to purchase parts or acces-
sories, or if you have any questions, please contact us.
Thank you for purchasing Spectrum products!
Spectrum Industries, Inc
925 First Avenue, Chippewa Falls, WI 54729 USA
800 235 1262
715 723 6750
www.spectrumfurniture.com
™
72"W x 30"D Double desk
42"W x 30"D
Single ADA desk
0107821R11 Page 1 of 11

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 38979 and is the answer not in the manual?

Questions and answers

Related Manuals for Spectrum Industries 38979

Summary of Contents for Spectrum Industries 38979

  • Page 1 42”W x 30”D Thank you for purchasing Spectrum products! Single ADA desk Spectrum Industries, Inc 925 First Avenue, Chippewa Falls, WI 54729 USA 800 235 1262 715 723 6750 www.spectrumfurniture.com...

  • Page 2: Assembly & Set-Up

    If servicing is • Do not step on, drive over, drag, or place objects on power cords. necessary, please contact Spectrum Industries for assistance. • For added safety, plug into a grounded outlet controlled by a GFI (Ground Fault Interrupter) circuit breaker.
  • Page 3 2. Install glides Glide wrench 1. Carefully lift one side of the desk and place a short wooden 4x4 or 2x4 block (or equivalent support) under the leg. This may require two people. Figure 2. 2. Thread the two glides into the leg, tighten securely, and remove block. 3.

  • Page 4: Monitor Installation

    4. Monitor installation 1. Attach the VESA mount (butterfly-shaped portion) to the back of your flat panel monitor with (4) M4 x 12mm PHM screws. (Holes on top, slots on bottom). Figure 4.1. Note: On most flat panel monitors, it will be necessary to remove the standard base that comes with the monitor to use the VESA mounting option.
  • Page 5 5. CPU installation (Note-some desks do not include CPU slings) 1. Set the CPU unit into the CPU sling. 2. Make sure the CPU will be supported by both straps. Tighten the straps around the CPU while keeping the buckles positioned as high as possible to avoid interference. Figure 5.1. Note: The center slot can be used for better support of smaller profile CPU’s.

  • Page 6: Cord Management

    6. Cord management 1. With the back panel removed, connect the necessary monitor, keyboard, and mouse cords above the worksurface. 2. Position the keyboard as shown approximately 6” from the front edge of the worksurface with the mouse on the opposite side of the CPU as shown.
  • Page 7 4. With the loom removed, feed the monitor, keyboard, and mouse cords through the sliced opening of the loom to the bottom of the desk as shown. Figure 6.4. 5. Split the CPU wires out of loom approximately 3/4 of the way down the loom and plug into the CPU. 6.

  • Page 8: Operation

    Operation For classroom (worksurface) use: For computer use: 1. Place the keyboard and mouse in the compartment tray under the monitor. 1. Open the monitor compartment lid. 2. Lower the monitor by pushing down on the lift bracket until the 2.

  • Page 9: Maintenance

    Instructor-side panel removal Metal panel: Laminate panel: 1. The panel is designed for easy removal using keyhole slots and 1. Open the monitor compartment lid. 1/4-20 JC bolts. If the bolts are tight, slightly loosen with a 4mm 2. Unscrew the 1/4-20 thumbscrews securing the panel. Figure 8.2. hex wrench.
  • Page 10 Accessories Note: Slings and cover plates are available should it later be necessary to convert from or to CPU towers. Single desks take one sling or cover plate, double desks take two. CPU Sling for 24”D desks - 38981 Cover Plate - 38978 •...

  • Page 11: Warranty

    5 Years Customer supplied material No Warranty DESIGNED AND ASSEMBLED IN CHIPPEWA FALLS WISCONSIN.USA 925 FIRST AVENUE, CHIPPEWA FALLS, WI 54729 / 800-235-1262 / 715-723-6750 / WWW.SPECTRUMFURNITURE.COM © 2019 Spectrum Industries Inc., All rights reserved. 0107821R11 Page 11 of 11...

This manual is also suitable for:

Flex insight desk

Table of Contents