Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for XAG P20 2019
Summary of Contents for XAG P20 2019
- Page 1 P20 2019 Quick Start Guide Version 1.0...
-
Page 3: How To Contact Us
To users: Dear users, thank you for choosing XAG products. For SAFETY reasons and for the best experience possible, XAG recommend that you should read through this Quick Start Guide and Disclaimer within this document before attempting to use the P20 2019 Plant Protection UAS. - Page 4 Quick start guide P20 Plant Protection UAS Main structural components of P20 Plant Protection UAS are as follows: (Above) attached figure 1. Airframe module structure figure 1 (Below) attached figure 2. Airframe module structure figure 2 Propeller Head cover Liquid container Smart battery RTK antenna (one on each side) Motor...
- Page 5 Quick start guide No.4 Arm No.1 Arm No.2 Arm No.3 Arm (Above) Figure 3. Airframe module & Arm orientation (Below) Figure 4. Airframe module FC Backup Power Radar (Front) RTK UAV module Antenna Hub 4G antenna frame Radar (Right)* Radar (Rear) Flight status indication light (tail light) Airframe nameplate (serial number/QR code) Radar (Left)*...
-
Page 6: List Of Items
List of items Before unpacking and using the product, please carefully check to see if it contains all the items listed in this list. Please contact XAG or your dealer if there are any missing items. Airframe No. 4 Arm No. - Page 7 Quick start guide Assembling of aircraft Preparations before assembling In order to facilitate transportation, the head cover, antenna frame components, center hatch cover and arm fixing slider of P20 have been installed on the aircraft body before leaving the factory. User will need to remove these parts temporarily before assembling the aircraft, and install them back to their original position after installing the arms.
- Page 8 Quick start guide 4.Remove liquid container holder Remove the Liquid container fixing screws and temporarily remove the container holder Before the reassembling the arm, please be certain to match the corresponding markings Atten on the upper plate of the fuselage to the markings on aluminum sleeve of each arm. (Refer to Page 5).
- Page 9 Quick start guide Arms installation Buckle Slider 5 . D i s m a n t l e t h e f i x e d 6. Install No.1 and No.2 arm sliders of No.1 and No.2 arm Insert the No.2 short arm from designated position of airframe plate, and then install Dismantle the screws (4 screws on 2 the top slider back to its original position to...
- Page 10 Quick start guide Connecting Infusion Tube 9. Connect circuits and infusion tube correctly After installation of arms, all the plugs of each circuit and the infusion of the spray system should be correctly connected. For the connection, see "P Series Aircraft Modules Wiring Guidelines"...
-
Page 11: Finish Assembly
Quick start guide 11.Finish Assembly The battery and the Liquid container are sequentially loaded onto the aircraft, and the Aircraft assembly is completed. www.xa.com... - Page 12 Quick start guide P Series Aircraft Module Wiring Guidelines V1.1 HDLS Module RTK Module 4G – Left Antenna 4G–Right Antenna 2.4G/5.8G - Right antenna 2.4G/5.8G-Left Antenna RTK-Left Antenna RTK–Right Antenna Diagram-Antenna Hub NO.1 Motor NO.2 Motor Power system Load system power supply NO.3 Motor NO.4 Motor Diagram-Power Grid...
- Page 13 Quick start guide P Series Aircraft Module Wiring Guidelines V1.1 Smart battery Uninterruptible Power Supply Load system XCope system Power system Terrain sensor GNSS RIK positioning module PC upgrading port FC Status Indicator High Data Link Module Auxiliary Port1 SBUS No.2 nozzle No.1 nozzle Liquid...
-
Page 14: Activation Steps
2. Select “Scan QR”, and add your device by either entering the Serial Number or the Scanning the QR Code of the Aircraft (This information could be found on the Airframe Nameplate). 3. Please Scan the QR Code on the Activation Card provided by Official XAG Partners to activate your device. -
Page 15: Prepare The Remote Controller
Quick start guide 2. Prepare the remote controller XAG P series UAV needs to be used together with professional remote controller and APP, which supports various control modes. Currently, the supported control equipment (combination) includes: 1: ACB1 CommBack (standard) + Smart phone;... - Page 16 STEP 4 – to be paired. Atten Only on the XAG member platform can a UAS with the right to use be successfully paired. •Precautions 1. The distance between your phone and the CommBack shall be maintained at 20cm-10m, and it shall be noted that your phone shall not be too close to the CommBack to avoid interference from your phone with the signal of CommBack.
- Page 17 Quick start guide 3. Preparation of smart battery The P-Series Plant Protection UAVs are designated to be powered by B12620/ Normally on: norma lash slowly: low temperature B 1 2 8 0 0 S m a r t b a t t e r y . T h e S m a r t Flash quickly: high temperature Battery contains a power button and six Double flashing: failure...
- Page 18 Quick start guide Charging by P-Series Rapid Charger Charging by a Power Bank The battery must be charged by the designated charging device, and all consequences caused by use of Atten non-designated charging device shall be borne by the user. 4.
- Page 19 Quick start guide 5. Aircraft Status The Flight Indicator indicates the status on the aircraft. See the table below for details of the Flight Indicator: Flight Status Indicator Status State description ONE RED + ONE GREEN LIGHT FLASH WEAK GPS SIGNAL Manual TWO LIGHT FLASHING (Green) GOOD GPS SIGNAL...
-
Page 20: Technical Specifications
Quick start guide Technical Specifications Electronic speed controller Model: VC12100 P20 multi-copter plant Maximum operating voltage: 52.2V (12SLipo) protection aerial platform Maximum continuous operating current: 100A Overall dimensions: 1,172×1,179×490mm Overall dimensions: (when the propellers are folded) Foldable propeller Material: nylon carbon fiber Overall dimensions: 1,852×1,828×490mm Number of main copters: 4... - Page 21 Quick start guide Communication system Other features Operating frequency: 2.400-2.483GHz Operating efficiency: 12ha/h High-precision radar: (5 radars + XCope) omnibearing 5.725-5.850GHz High-precision radar: obstacle avoidance, autonomous Transmission power (EIRP): 2.400-2.483GHz High-precision radar: obstacle avoidance Transmission power (EIRP): FCC≤28dBm AI intelligent engine 3D operation planning: support Transmission power (EIRP): CE≤20dBm High-precision flow measurement: support...
- Page 22 XAG server during use. In the event that the flight records and data cannot be uploaded and saved and XAG cannot analyze the flight records and data due to any reason of the user, XAG will not assume any responsibility.
- Page 23 Quick start guide Real-name registration In order to strength the management of civil UAVs, Civil Aviation Administration of China (CAAC) issued the Regulations on “Real-name Registration of Civil Unmanned Aerial Vehicles”, which requires the owners of civil UAV’s to register in real name and attach the registration marks in accordance with the Regulation.
- Page 24 All information of this user manual (including but not limited to any text description, illustrations, photos, methods and processes, etc.) belongs to XAG Co., Ltd. and is protected by copyright law. Without written authorization, no individual or institution shall reproduce, extract, translate, distribute or otherwise reproduce or quote all contents of this manual...