Advertisement
Discontinue
Ｉ Ｎ Ｓ Ｔ Ｒ Ｕ Ｃ Ｔ Ｉ ＯＮ ＭＡ Ｎ Ｕ Ａ Ｌ
Ｐ Ａ Ｒ Ｅ Ｃ Ｔ
Ｅ Ｌ Ｅ Ｃ Ｔ Ｒ Ｏ −Ｐ Ｎ Ｅ Ｕ ＭＡ Ｔ Ｉ Ｃ
Ｒ Ｅ Ｇ Ｕ Ｌ Ａ Ｔ ＯＲ
Ｅ Ｒ １ ０ ０
Please read this instruction manual
●
carefully before using this product,
particularly the section describing
safety．
●
Retain this instruction manual with the
product
for
whenever necessary．
Ｓ Ｍ − ２ ７ ７ ３ ４ ６ −Ａ
further
consultation
Advertisement
Table of Contents
Related Manuals for CKD ER100
Summary of Contents for CKD ER100
- Page 1 Discontinue Ｓ Ｍ − ２ ７ ７ ３ ４ ６ −Ａ Ｉ Ｎ Ｓ Ｔ Ｒ Ｕ Ｃ Ｔ Ｉ ＯＮ ＭＡ Ｎ Ｕ Ａ Ｌ Ｐ Ａ Ｒ Ｅ Ｃ Ｔ Ｅ Ｌ Ｅ Ｃ Ｔ Ｒ Ｏ −Ｐ Ｎ Ｅ Ｕ ＭＡ Ｔ Ｉ Ｃ Ｒ...
- Page 2 Discontinue Ｆ ｏ ｒ Ｓ ａ ｆ ｅ ｔ ｙ Ｕ ｓ ｅ To use this product safety, basic knowledge of pneumatic equipment, including materials, piping, electrical system and mechanism, is re- quired (to the level pursuant to JIS B 8370 Pneumatic System Rules). We do not bear any responsibility for accidents caused by any person without such knowledge or arising from improper operation. Our customers use this product for a very wide range of applications, and we cannot keep track of all of them. Depending on operating condi- tions, the product may fail to operate to maximum performance, or cause an accident. Thus, before placing an order, examine whether the product meets your application, requirements, and how to use it. This product incorporates many functions and mechanisms to ensure safety. However, improper operation could result in an accident. To pre- vent such accidents, read this operation manual carefully for proper operation. Observe the cautions on handling described in this manual, as well as the following instructions: ！ DANGER： Failure to pay attention to DANGER notices may cause a situation that results in a fatality or serious injury and that ...
-
Page 3: Design And Selection
Basically, the attitude of installation shall be vertical (i.e., the black portion of the coil ！ CAUTION should face upward). In the event of the horizontal installation, the unit should be re-adjusted for zero point as well as span. ２ ） Install the unit in a place where the vibration is 2m/s , 10Hz or less. ３ ） Avoid operating the product in places where it may be affected by direct sunlight, water or oil. ４ ） Flush air into the pneumatic pipes employed in the PARECT electro-pneumatic regulator before connection ５ ） The model ER100 always bleeds the secondary air pressure from the relief hole provided on the side, generating a bleeding sound. This bleeding sound is normal although it grows as the secondary side pressure increases. ６ ） For the input signal specifications, the model ER100 is available in the voltage input type (0 to 10V) and the current input type (4 to 20mA). Check the type of your model before use. USAGE AND MAINTENANCE １ ） When the primary side pressure is applied to the unit, do not loosen the screw ！ WARNING securing the orifice. Otherwise, the orifice will fly out. ２ ） Do not disassemble the unit because it will fail. Operations of the disassembled unit ... - Page 4 Discontinue INDEX ＥＲ１００ Series PARECT Electro‑pneumatic Regulator INSTRUCTION MANUAL No.SM‑277346‑A １ ． PRODUCTS １ ． １ Specifications ･･････････････････････････････････････････ ４ １ ． ２ Dimensions ････････････････････････････････････････････ ５ ２ ． INSTALLATION ２ ． １ Installation Position ･････････････････････････････････････ ６ ...
-
Page 5: Specifications
Discontinue １ PRODUCTS 1.PRODUCTS 1.1 Specifications Model ＥＲ１５０ ＥＲ１７０ Item Media (Refer to CAUTION) Cleaned air Working pressure range 0.39 ‑ 0.78MPa Pressure control range ※１ 0.0098 ‑ 0.49MPa 0.0098 ‑ 0.69MPa Voltage Input Voltage rate 0 ‑ 10VDC 0 ‑ 10VDC Input 2‑wire type Input impedance 400Ω 500Ω Signal Current Input current rate 4 ‑ 20mADC ※２ 2‑wire type Input impedance 250Ω Insulation resistance ... - Page 6 Discontinue １ PRODUCTS 1.2 Dimensions Port size（Ｄ） Ｒｃ３/８ Ｒｃ１/４ Fig２ Dimensions −5− [SM‑277346‑A] ...
-
Page 7: Installation
Insert both hooks of the cap inside the box. Insert the cap straight onto the box till the hooks lock. Fig３ Connect (+) and (‑) of the input signal from other unit, etc. to the terminal box of the model ER100 unit, as shown in Fig.4. ＋ Input signal Terminal Stand Input signal− ... - Page 8 Discontinue ３ INSTALLATION ３ ． INSTALLATION ３ .１ Adjustment Factory adjustment is given prior to shipment so adjusted for upright installation (coil riding atop of regulator). Zero and Span adjustment at factory Model Zero（MPa） Span（MPa） ＥＲ１７０ ０．０１ ０．６９ ＥＲ１５０ ０．０１ ０．４９ When it is required to mount it otherwise or to control pressure with higher accuracy, give a zero adjustment （ 0.01MPa） in accordance with the following procedures after mounting a pressure gage of accuracy commensurating with the accuracy expected on the secondary side. A span adjustor is attached to the electro-pneumatic regulator for the purpose of adjusting the set pressure at the maximum rating of input electric signal. Making use of this, the conversion between input signal voltage and set air pressure is done easily. Make span adjustment, as same principle as that of zero adjustment, while watching the mounted high accuracy pressure gage commensurating with that of expected. Span adjustment range：ER170 0.39 ‑ 0.69MPa（Working pressure:0.79MPa） :ER150 0.34 ‑ 0.49MPa（Working pressure 0.59MPa） However, it varies depending upon working pressure Procedure−１ Adjust operational pressure.(primary side). Procedure−２ ...
- Page 9 Discontinue ４ MODEL ４ ． HOW TO ORDER Ｅ Ｒ １ A ０ − B C − D Symbol Optional blacket No symbol Nothing Blacket attached Ｂ Symbol Port size ０８ Ｒｃ１ /４ １０ Ｒｃ３ /８ Symbol Input signal ０ ０ ‑ １０VDC ...
Need help?
Do you have a question about the ER100 and is the answer not in the manual?
Questions and answers