Subscribe to Our Youtube Channel
Related Manuals for APPA M1
Summary of Contents for APPA M1
- Page 1 User Manual YEAR S LIMITE D WARRANTY Pocket-Size True RMS Multimeter Карманный мультиметр TRMS...
- Page 2 Read First Safety Information Understand and follow operating instructions carefully. WARNING • Remove test lead from Meter before opening the battery door or Meter case. protection by the Meter might be impaired. • Always use proper terminals, switch position, and range for measurements.
- Page 3 Caution • Disconnect the test leads from the test points before changing the position of the function rotary switch. • Never connect a source of voltage with the function rotary position. • Do not expose Meter to extremes in temperature or high humidity.
- Page 4 Front Panel Illustration 1. VoltSeek Light 2. LCD display : 6000 counts 3. Push-buttons. function. 5. Input Terminal for 6. Common (Ground reference) Input Terminal. VoltSeek Light LCD display Button Rotary switch V, Hz of Voltage, Input Common Input Making Basic Measurements basic measurements.
- Page 5 Caution When connecting the test leads to the DUT (Device Under Test) connect the common test leads before connecting the live test leads ; when removing the test leads, remove the live test leads before removing the common test leads. Measuring AC / DC Voltage Dial the switch and press the Function button to select the measuring function.
- Page 6 Measuring Frequency Dial the switch to select the measuring function. Measuring Resistance / Capacitance Dial the switch and press the Function button to select the measuring function.
-
Page 7: Using The Function
Measuring Continuity / Diode Dial the switch and press the Function button to select the measuring function. Using The Function Function Button Switch Function Position Press the Function button to change the function on the same switch position. - Page 8 Peak Hold In the Peak Hold function, the meter records the peak min. value and the peak max. value when the inputs goes below the recorded peak min. value or above the recorded peak max. value,the meter records the new value . Press Hold button to pause the recording.
- Page 9 VoltSeek Keep the VoltSeek button down to activate the VoltSeek function. WARNING If the VoltSeek LED is not on, voltage could still be present. Wake-up the meter by dialing the switch or pressing any button.
- Page 10 down and turn the meter on. Relative button to start relative. The meter remembers the presently reading as reference and shows the indication “ ” on the display. - In this mode, the meter deducts the reference from each reading, and shows the result on the display.
- Page 11 Low battery and Battery Replacement Replace the battery as soon as the low battery indicator appears, to avoid false reading. Battery Cover Screw 1.5V AAA x2 Battery Caution Remove test leads from Meter before opening the battery cover or Meter case. Maintenance Do not attempt to repair this Meter.
- Page 12 Display Count : 6000 count Overrange Display : OL or -OL Conversion Rate : Dimensions(W x H x D) : 68 x 138 x 30mm Weight : 200g Power requirement : AAA size 1.5 x2 Battery Life : 300 hours Alkaline battery LVD : EN61010-1, EN61010-2-030 EMC: EN61326-1 Installation Category : CAT.III.
- Page 13 Accuracy is given as ±(% of reading + counts of least than 80% R.H. The crest factor may be up to 3.0 as 4000 counts. For non-sinusoidal waveforms, Additional Accuracy by Crest Factor (C.F.) : Add 1.0% for C.F. 1.0 ~ 2.0. Add 2.5% for C.F.
- Page 14 DC mV Range OL Reading Resolution Accuracy 600.0mV 660.0mV 0.1mV ±(0.5% +5D) Input Impedance : Overload Protection : Resistance Range OL Reading Resolution Accuracy ±(0.5% +5D) ±(0.5% +2D) ±(1.0% +5D) There is a little rolling less then ± 50 digits when Overload Protection: Continuity Range...
- Page 15 Diode Range OL Reading Resolution Accuracy 1.500V 1.550V 0.001V ±(1.0% +3D) Open Circuit Voltage: Approx. 1.8V Overload Protection: Capacitance Range OL Reading Resolution Accuracy 50.00nF 55.00nF 0.01nF ±(2.0% +10D) 500.0nF 550.0nF 0.1nF ±(2.0% +5D) Overload Protection : Maximum Response Time : 2 seconds (<0.5mF) , Frequency Range...
- Page 16 VoltSeeK 90V~600V(50Hz~60Hz) Peak Hold(for Voltage & Ampere Function) Limited Warranty This meter is warranted to the original purchaser against defects in material and workmanship for 3 years from the date of purchase. During this warranty period, Manufacturer will, at its option, replace or repair the defective unit, This warranty does not cover fuses, disposable batteries, or damage from abuse, neglect, accident, unauthorized repair, alteration, contamination, or abnormal conditions of...
- Page 17 • • • • • • • • • • • • • •...
- Page 18 • • • •...
- Page 28 66.00...
- Page 29 Accuracy ±(0.5% +5D) 600.0 660.0...
- Page 32 • • • • • • • • • • • • • •...
- Page 33 • • • •...
- Page 43 66.00...
- Page 44 ±(0.5% +5D) 600.0 660.0...
- Page 58 66.00...
- Page 59 ±(0.5% +5D) 600.0 660.0...
- Page 72 LVD: EN61010-1, EN61010-2-030 EMC: EN61326-1 0 °C ~ 30 °C ( 30 °C ~ 40 °C ( 40 °C ~ 50 °C ( IP40...
- Page 73 ±(0.5% ±(1.0%...
- Page 74 ±(0.5% + ±(0.5%...
- Page 75 ±(2.0% ±(2.0% ±(0.1%...
- Page 77 APAC MGL APPA Corporation cs.apac@mgl-intl.com Flat 4-1, 4/F, No. 35, Section 3 Minquan East Road, Taipei, Taiwan Tel: +886 2-2508-0877 700020039...
Need help?
Do you have a question about the M1 and is the answer not in the manual?
Questions and answers