Advertisement
Quick Links
Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method
of ceiling mounting inverted LCD/DLP projectors. Its low profile design offers roll, pitch, and yaw adjustment. The VMPR1 steel-to-steel
construction with adjustable height to maintain proper ventilation, hold registration for quick lamp changes and easy filter cleaning without
loosing registration. The VMPR1 ceiling mount includes an NPT Extension Pipe that may be used where more room is required, such as
areas with vaulted or cathedral ceilings.
The maximum weight to be installed on the VMPR1 ceiling mount is 50 pounds [22.68 Kg]. Improper installation may result in
serious personal injury. Make sure the structural members can support a redundant weight factor five times the total weight
of the equipment. If the structure can not support this weight, reinforce the structure prior to installing the VMPR1.
If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or
contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our
customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts
for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Do not use this product
for any purpose that is not explicitly specified by Sanus Systems. Please call Sanus Systems before returning products to the point of
purchase.
Required Tools: Open End Wrenches, Phillips screwdrivers, Allen Wrenches (provided), other tools may be required depending on the
method of installation.
Supplied Parts and Hardware: (All threaded fasteners are shown full size.)
Universal Projector Interface - A
Qty. 1
Adjustment Bracket - D
Qty. 1
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 11.09.06 (6901-100023)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Assembly Instructions for Model: VMPR1
NPT Adapter - E
Bottom Cover - G
Qty. 1
WARNING:
Extension Arm - B
Qty. 2
Qty. 1
Top Cover - H
Qty. 1
Ceiling Plate - C
Qty. 1
NPT Extension Pipe - F
Qty. 1
Advertisement
Related Manuals for Sanus Systems VMPR1
Summary of Contents for Sanus Systems VMPR1
- Page 1 The VMPR1 ceiling mount includes an NPT Extension Pipe that may be used where more room is required, such as areas with vaulted or cathedral ceilings.
- Page 2 Qty. 4 Qty. 4 Lag Bolt - U Allen Key - W Allen Key - V Qty. 2 Qty. 1 Qty. 1 VMPR1 Dimensional Drawings [470.15 mm] 18.51 in Covering area with Extension Arms (B) installed [305 mm] 12.01 in...
- Page 3 This information is normally listed in the projector specifications for set-up. The hardware provided with the VMPR1 is designed to be secured to a wood framing member. For installations other than this, consult a qualified contractor. Use a high quality Stud Sensor to locate a stud in the area that you plan to mount the VMPR1 as shown in Diagram 1A.
- Page 4 Step 2: Attach Universal Projector Interface to Projector Loosen, but do not remove the Acorn Nuts shown in Diagram 2A. Place the Universal Projector Interface (A) on the projector, aligning the holes in the Adjustable Feet with the threaded holes in the projector and with the Threaded Suds in line as shown in Diagram 2A.
- Page 5 Step 3A: Attach Ceiling Plate to Adjustment Bracket - Flat Ceilings NOTE: If the projector is being mounted in an area where it must be lower from the ceiling, such as areas with vaulted or cathedral ceilings, proceed directly to Step 3B - Attach Ceiling Plate to Adjustment Bracket using Extension Pipe and NPT Adapter - Vaulted or Cathedral Ceilings.
- Page 6 Step 4A: Attach VMPR1 Top Assembly to Ceiling and install Top Cover - Flat Ceilings Using the Lag Bolts (U) and Lag Bolt Washers (T) secure the VMPR1 Top Assembly to the framing member at the location selected in Step 1: Ceiling Preparation.
- Page 7 Diagram 5A. NOTE: The two halves of the VMPR1 attach by lifting the and rotating the Universal Projector Interface (A) so that the Threaded Studs with Tapered Nuts (K) rotate into the Vee Slots of the Adjustment Bracket (D) as shown in Diagram 5A.
- Page 8 Step 6 - Projector Alignment The VMPR1 can be adjusted for vertical elevation (Pitch), horizontal tilt (Roll), and rotation (Yaw). Pitch Adjustment Loosen the Pitch Adjustment Screws on both sides of the Adjustment Bracket (D) and adjust the projector to the desired Pitch;...