Advertisement
Quick Links
Assembly Instructions for Model: VMAA26
Thank you for choosing a Sanus Systems VisionMount™ wall mount. The VMAA26 is designed to mount up to 50" Flat panel televisions
weighing up to 130 lb. to a vertical wall. It allows you to tilt the television from +5° to -15°. It will also extend 25.75" away from the wall,
swivel up to 180°, and roll ± 6°.
CAUTION: The size and weight of your television must not exceed 50" [1270 mm] diagonally and 130 Lbs [59 Kg]. The wall
must be capable of supporting five times the weight of the television plus the wall mount. Never use defective parts. Improper
installation may cause property damage or personal injury. Do not use this product for any purpose that is not explicitly
specified by Sanus Systems.
If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor
or contact Sanus at 800.359.5520 or www.sanus.com. Our customer service representatives can quickly assist you with installation
questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly
to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury
caused by incorrect mounting, incorrect assembly, or incorrect use. Please call Sanus Systems before returning products to the point of
purchase.
NOTE: This mount is not intended for use on brick, concrete block, concrete, or steel wall studs. Typical wall anchors do not
have sufficient holding power to support this mount. It is up to the installer to verify the safety of any installation method or
hardware that is not provided by or recommended by Sanus Systems. Sanus Systems makes every effort to assure all necessary
television mounting hardware is included. If the television mounting hardware you need is not included please consult your
local hardware store or call Sanus Systems
Required Tools: 3/16" drill bit, drill, adjustable or crescent wrench, Phillips screwdriver.
Supplied Parts: (Some parts are not shown at same scale)
Preventor - C
Wall Plate - A
Arm Assembly - B
Qty. 1
Qty. 1
Qty. 1
I" Diameter Tube - D
Monitor Bracket - E
Vise Assembly - F
Qty. 2
Qty. 2
Qty. 4
Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 09.26.06 (6901-100017)
Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com
Advertisement
Related Manuals for Sanus Systems VisionMount VMAA26
Summary of Contents for Sanus Systems VisionMount VMAA26
- Page 1 Replacement parts for products purchased through authorized dealers will be shipped directly to you. Check carefully to make sure that there are no missing or defective parts. Sanus Systems can not be liable for damage or injury caused by incorrect mounting, incorrect assembly, or incorrect use.
- Page 2 Hardware: (Hardware shown is actual size) Wire Tie - H Wire Tie Clip - G Qty. 10 Qty. 7 Lag Bolt - I Lag Bolt Washer - J 7/32 & 3/16 Allen Keys - K Qty. 4 Qty. 4 Qty. 1 Each 1/4-20 Nut - M Preventor Bolt - O Safety Bolt - N...
- Page 3 Step 1: Mounting Monitor Brackets to a Televisions with a flat back NOTE: For TVs with a curved back or any other obstruction See Step 2. After completing this step, proceed to Step 3. Determine the diameter of the Bolt (P,Q,R,S) your TV requires by hand threading them into the threaded insert on the back of the TV.
- Page 4 Step 2: Mounting the Monitor Brackets to Televisions with a curved back or other obstruction. Determine the diameter of the Bolt (T,U,V,W) your TV requires, by hand threading them into the threaded insert on the back of the TV. If you encounter any resistance stop immediately. Once you have determined the correct diameter, refer to the appropriate Diagram below.
- Page 5 Step 3: Add the Vise Assemblies to the Monitor Brackets: NOTE: Do not overtighten the 1/4-20 Nut (M). The Vise Assembly (F) should be able to rotate freely around the Carriage Bolt (L). Place the Vise Assembly (F) into the Monitor Bracket (E) so that the two Jaws point toward the set of 1” diameter holes and the Allen Bolt is facing away from the television.
- Page 6 Step 4: Attach the Arm Assembly to the Television (Continued) CAUTION: The 1” Diameter Tubes (D) must extend beyond the outside edges of both Monitor Brackets (E) and the Allen Bolts in all 6 Vise Assemblies (F) must be tightened. Failure to do this will result in an installation that unstable and may result in property damage and/or personal injury.
- Page 7 Step 6: Hang the assembly onto the Wall Plate CAUTION: This step may require two people to lift the assembly onto the Wall Plate. Sanus is not responsible for property damage and/or personal injury. Orient the Arm Assembly (B) so the arm extends directly away from the television and the Transfer Plate is parallel with the television.
- Page 8 Step 8: Add Preventor CAUTION: Avoid Pinch Points. Placing your hands or fingers between moveable parts (Pinch Points) may result in personal injury Determine which direction you want the Arm to fold. If you want the Arm to fold to the right, place the Preventor (C) on the right side of the Arm Assembly (B).