Related Manuals for Maiwe MISCOM8220G
Summary of Contents for Maiwe MISCOM8220G
- Page 1 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch User Manual Edition: V1.0) Wuhan Maiwe Communication Co., Ltd.
- Page 2 Copyright Copyright © Wuhan Maiwe Communication Co., Ltd. Clarification The user manual is applicable to MISCOM8220G layer 3 din-rail industrial ethernet switch. Please read the following license agreement carefully before using this manual. The products described in this manual can be used only if you agree on the following license agreement.
- Page 3 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Safe Use Instruction This product performance is excellent and reliable in the designed range of use, but it’s necessary to avoid man-made damage or destroy for the equipment. Read the manual carefully and keep this manual for reference if need afterwards.
-
Page 4: Table Of Contents
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Catalogue 1. Overview..............- 1 - 1.1. Product introduction..............- 1 - 1.2. System Features................- 1 - 1.2.1. High-performance Gigabit layer 3 industrial Ethernet switch..- 1 - 1.2.2. Industrial power supply design............- 2 - 1.2.3. -
Page 5: Overview
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch 1. Overview 1.1. Product introduction MISCOM8220G is a full Gigabit three-layer routing switch designed and developed by Wuhan Maiwe Communication Co. Ltd for industrial communication networks. This switch provides a high-end industrial Ethernet... -
Page 6: Industrial Power Supply Design
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch half-duplex), support automatic MDI/MDI-X connection, and support 4 Gigabit SFP optical ports. The fast fiber ring redundancy technology with less than 50ms enhances the reliability of system communication. Supports IEEE802.1Q-based VLANs, number 4094. -
Page 7: Packing List
The packing list of the switch is shown in Table 1-1 below. If any of the listed items is lost or destroyed, please contact the agent or the customer service center of Wuhan Maiwe Communication Co., Ltd. To help you to replace or make up. - Page 8 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Wavelength: 1310nm (single mode) 1550nm (single mode) 1310 nm (multimode) Transmission distance: <2Km (Gigabit multimode) Connector Type: LC Transmission rate: 1.25Gbps (gigabit) Input voltage: 24DC (18-36VDC), 48DC (36-72VDC), 220AC/DC Power parameter (85-264VAC/110-370VDC) Input power consumption: 15W (MAX)
-
Page 9: Hardware Installation And Networking
Abandoning the traditional heat sink cooling form, reducing the power consumption of the whole machine and improving the stability of the system. Figure 2-1 shows the dimensions of the MISCOM8220G: 156mm × 85mm × 137.7mm. Figure 2-1 Schematic diagram of the MISCOM8220G chassis... - Page 10 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch The front panel indicators of this series of switches indicate the current working status of the switch. The details are shown in Table 2-1 below. Table 2-1 Indicators on the front panel PWR1...
- Page 11 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch the fiber interface uses LC interface. The fiber interface needs to be used in pairs (TX and RX are a pair), the TX port is the optical transmitter, and the optical transceiver RX of the optical interface of another remote switch is connected, the RX port is the optical transceiver, and the same optical interface is connected to the same remote switch.
- Page 12 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Table 2-3 Power input terminal pin definitions and descriptions Pin definition illustrate Power supply 1 input V1+(AC-L)/positive (DC) Power 1 input V1-(AC-N) / negative (DC) Protected land (connected to the earth) Power 2 input V2+ positive (DC)
- Page 13 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Figure 2-4 Schematic diagram of the alarm relay Table 2-5 Relay output terminal pin definition and description Number Pin definition illustrate Alarm relay output normally open Alarm relay output common Alarm relay output...
-
Page 14: Hardware Installation
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Ground The MISCOM8220G industrial Ethernet switch has a grounding screw. The one end of the grounding wire is crimped to the cold-pressing terminal and then fixed to the grounding hole of the chassis with a grounding screw. The other end of the ground wire is reliably connected to the ground. -
Page 15: Host Installation
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch transmitted in a line to determine which lines should be separated. The rule of thumb is that wires with the same electrical characteristics can be bundled together. Separate the input and output lines. It is highly recommended that all equipment lines in the system be labeled when necessary. -
Page 16: Fiber Optic Connection
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Connecting network nozzle The CONSOLE port of this product can be connected to the serial port of the control computer. Connect the power supply When all other cables are connected, you can connect the power supply for the product identification specification. -
Page 17: Laying Cable
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Hot plugging steps: Observe the end of the PCB gold finger. Insert the gold finger end into the metal shield cage of the SFP. When you hear the sound of the cymbal, the device has been inserted into the position, and then the SFP is inserted and removed, and placed in the normal position parallel to the interface. -
Page 18: Simple Test
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch should be placed separately from other cables; The two ends of the cable should have corresponding markings. The content of the marking is concise and easy to maintain. Attention When laying the pigtail, it is necessary to prevent the cable from being knotted and the turning point should be minimized, and the turning radius should not be too small. -
Page 19: Fiber Port Test
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch pop up the console window, send ping 192.168.16.221 –l 1000 -t, (–l Refers to the number of bytes sent by the packet, -t means to keep sending data.) Run ping 192.168.16.220 –l 1000 –t in test computer 2 in the same way. If test computer 1 shows Reply from 192.168.16.221:bytes=1000 time<10ms... -
Page 20: Network Topology
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch 2.4. Network topology The switch can be flexibly networked. There are 6 basic topologies: star, chain, single loop, single loop coupling, and tangent loop coupling, as shown in Figure 2-12, Figure 2-13, Figure 2-14, Figure 2-15, Figure 2-16. -
Page 21: One-Way Coupling Between Rings
However, the above commitments do not cover damage caused by improper use, accidents, natural disasters, improper operation or improper installation. In order to ensure that consumers benefit from the products of Wuhan Maiwe Communication Co., Ltd., help and problem solving can be obtained by the following methods: Internet services Call the technical support office... -
Page 22: Technical Support Telephone Service
MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Co., Ltd., you can get more useful information and tips. 3.2. Technical support telephone service Call the company's technical support office, there will be professional technical engineers to help you solve the problems or problems you encounter in the first time. -
Page 23: Appendix
4. Appendix 1 RJ45 interface line sequence The MISCOM8220G series switches provide up to 16 RJ45 interfaces. In use, they can be routed to other Ethernet terminal devices via the network cable (direct or cross) of the switch RJ45 interface. Refer to Figure 3-1 below for the RJ45 pin number sequence. - Page 24 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Send/receive data Send/receive data (TRD1-) (TRD0-) Send/receive data Send/receive data (TRD1+) (TRD1+) Send/receive data Send/receive data (TRD3+) (TRD2+) Send/receive data Send/receive data (TRD3-) (TRD2-) Send/receive data Send/receive data (TRD0-) (TRD1-) Send/receive data Send/receive data...
- Page 25 MISCOM8220G Layer 3 Din-rail Industrial Ethernet Switch Note: The color definition of the cable in the figure refers to the EIA/TIA568B specification. Ordering information Table 2-1 Ordering information Gigabit Gigabit Item Power supply Tx port Fx port MISCOM8220G-4 Dual DC24V(18~36V...
- Page 26 WUHAN MAIWE COMMUNICATION CO.,LTD Add.:Building 2, Area E, Phase ii, Optical valley core center, No.52, Liufang road, East Lake Hi-tech Development Zone,Wuhan,China Phone: 027-87170215/16 Fax: +86-027-87170217 www.maiwe.com...
Need help?
Do you have a question about the MISCOM8220G and is the answer not in the manual?
Questions and answers