Canon iPF9000S Troubleshooting Manual page 57

Panel display
Code
(last 4
Large LCD
digits)
2E3A Roll1 jammed.
Manually rewind the
roll all the way
and press OK.
Roll1 (Uppr) jammed.
Manually rewind the
roll all the way
and press OK.
2E3B Roll 2 (Lwr) jammed.
Manually rewind the
roll all the way
and press OK.
2E3C Paper jam. Lift
the release lever.
2E3D Roll 1 (upper) jam
Lift the release
lever.
2E3E Roll 2 (lower) jam
Lift the release
lever.
2E3F Paper jam. Lift
the release lever.
2E40 Cannot print as
selected. Another
roll is in use.
[Stop]: Stop printing
2E41 Cannot print as
selected. Another
roll is in use.
[Stop]: Stop printing
2E42 MediaType Mismatch
2E45 MediaType Mismatch
Cutter Position Error
2E47
2F11 CR error
Call for Service.
Small LCD
During upper roll paper feeding operation,
the paper was fed with the roll feed sensor
detecting the paper, but the LF_PE sensor
could not detect the paper and the
operation timed out.
During lower roll paper feeding operation,
the paper was fed with the roll feed sensor
detecting the paper, but the LF_PE sensor
could not detect the paper and the
operation timed out.
During operations with cut sheet, the state
of the LF_PE sensor has become invalid.
During operations with upper roll paper, the
paper was fed with the roll paper detection
sensor and the roll feeding sensor detecting
the paper, but the state of the LF_PE sensor
became invalid.
During operations with lower roll paper, the
paper was fed with the roll paper detection
sensor and the roll feeding sensor detecting
the paper, but the state of the LF_PE sensor
became invalid.
When either upper or lower roll paper is in
operation, the states of the roll paper
detection sensor, roll feeding sensor, and
LF_PE sensor became invalid.
Print data having lower roll paper
specification has been received while upper
roll printout remains.
Print data having upper roll paper
specification has been received while lower
roll printout remains.
Paper mismatch (type/ restart printing of
suspended job)
It occurs when all of the following conditions
are met:
・[Stop] selected for [Paper Mismatch
Detection] in menu settings.
・[Change Paper] button was pressed for
suspended jobs from host.
・The paper type that has been set in the job
and the type of actually fed paper do not
match.
Paper mismatch (type/ restart printing of
suspended job)
It occurs when all of the following conditions
are met:
・[Stop] selected for [Paper Mismatch
Detection] in menu settings.
・The paper width that has been set with
data and the paper width of actually fed
paper do not match.
Cut Failure
The cutter is not at home position when
restart from jam. Also paper feeding was
detected.
Power On An operation order has been issued while
Again the carriage suffered a hardware error.
CR Error
2-45
Explanation/Detection sequence
Chapter 2 Indexes by Case
Remedial Action
(★: Reference fault
isolation procedure or
tool)
①Manually rewind the
paper and reload.
Go to ★2E25.
①Manually rewind the
paper and reload.
Go to ★2E25.
①Reload the paper.
Go to ★2E25.
①Reload the paper.
Go to ★2E25.
①Reload the paper.
Go to ★2E25.
①Reload the paper.
Go to ★2E25.
Remove the printout
of upper roll, and print
again.
Remove the printout
of lower roll, and print
again.
Continued printing
allowed.
Replace with
appropriate paper.
Continued printing
allowed.
Check the driver
settings.
Replace with
appropriate paper.
Check
around the cutter unit.
Go to ★2F26
(P3-4).