Cisco AS5400 Installation Manual page 84

Index
E
E1 network specifications (table)
environment monitoring
environment status, checking
ESD wrist-strap, safety
1-3
F
Figures
2-Port or 4-Port T1 or E1 DFC LEDs
2-Port T1 or E1 DFC
3-1
4-Port T1 or E1 DFC
3-2
8-Port T1/E1 Interface Cable
8-Port T1 or E1 DFC
3-2
8-Port T1 or E1 DFC LEDs
Bantam Ports 6-9
Blank DFC Cover
2-5, 3-6, 4-5, 5-5
Carrier Card With Two 8 PRI CT1/CE1 Cards
Connecting the 36-Pin Cable Connector to an 8-port T1
DFC A-9
CT3 Cable Assembly
Install the Carrier Card in the Cisco AS5350
Install the Carrier Card in the Cisco AS5400
Install the DFC in the Cisco AS5400
Install the T1 or E1 DFC in the Cisco AS5350
Install the T1 or E1 DFC in the Cisco AS5400
Install the T3 DFC in the Cisco AS5350
Install the T3 DFC in the Cisco AS5400
Install the Universal Port DFC in the Cisco AS5350
J-45 to DB-15 Interface Cable
Loosen the Captive Screws on the Cisco AS5350
3-5, 4-4, 5-4
Loosen the Captive Screws on the Cisco AS5400
3-5, 4-4, 5-4
Placing the Molded RJ-45 End of the Cable on the
Bracket A-5
Remove the DFC from the Cisco AS5350
Remove the DFC from the Cisco AS5400
Removing the Carrier Card from the Cisco AS5350
Cisco AS5350 and Cisco AS5400 Universal Gateway Card Installation Guide
IN-2
3-2
6-6
6-7
6-1
A-3
6-2
2-2
A-10
2-5
2-5
5-7
3-9
3-10
4-6
4-6
A-2
3-6, 4-5, 5-4
3-6, 4-5, 5-5
Removing the Carrier Card from the Cisco AS5400
RJ-45 to Bare Wire Interface Cable
RJ-45 to BNC Interface Cable for 75-Ohm, Unbalanced
Connections
RJ-45 to RJ-45 Interface Cable
RJ-45 to Twinax Interface Cable for 120-Ohm,
Balanced Connections
Routing Cables with Molded RJ-45 Ends of Cables
Flush with Bracket Edges
Routing Cables with Molded RJ-45 Ends of Cables Next
to Each Other
Securing the Cable Bracket to the Rack
Slot Numbering on the Cisco AS5350 Chassis
5-2, 6-6
Slot Numbering on the Cisco AS5400 Chassis
5-3, 6-6
T3 DFC LEDs
T3 Dial Feature Card
Tighten the Captive Screws on the Cisco AS5350
3-10, 4-6, 5-8
Tighten the Captive Screws on the Cisco AS5400
3-10, 4-7, 5-8
Universal Port DFC
Universal Port DFC LEDs
G
ground connection first warning
ground connections, safety
H
5-7
hardware features, new
2-3, help, getting
2-4,
I
input impedance, configuring
input impedance, verifying
installation instructions warning
2-4 installing a carrier card
A-2
A-2
A-2
A-2
A-7
A-6
6-2
4-1
5-1
6-2
1-2
1-2
xiii
xii, 2-7, 3-14, 4-7, 5-9, 6-10
3-11
3-11
1-2
2-5
2-4
A-8
3-3, 4-2,
3-4, 4-3,
2-6,
2-6,
78-13311-01