Advertisement
S S
a a
v v
S S
a a
v v
The effects processor comes shipped from the factory with the
presets set at program 01 for preset #1, 02 for #2, 04 for #3 and 08
for #4. (These are also the settings the unit reverts to when it is reset
- see page 19.)
Any of the 100 programs may be stored as any of the presets (up
to 16 with the use of footswitches - see pages 25 - 34). To assign an
effect as a preset, turn the processor ON and follow this example:
Example 1: Assigning effect #32 as preset #1:
1. Press preset button #1. The LED next to the button will light up.
2. Turn the PROGRAM knob until the display window shows "32."
The #1 preset is now temporarily set as "32" - it will remain that
way until the unit is turned off. To lock the preset in memory (so it will
be there when the unit is turned on again later):
3. Press the EDIT button two times. The EDIT LED will light up (along
with the STYLE or LEVEL LED) at the first press, then go out at
the second press.
The #1 preset is now "permanently" set as "32" - it will stay there
until you store another program in preset #1.
E E
d d
i i
t t
i i
E E
d d
i i
t t
i i
Any of the programs (except the tuner) may be custom-tailored,
then saved to memory if desired. For each program, two characteris-
tics may be modified: the level and the style. Style refers to a specif-
ic parameter (such as decay time for reverbs), determined by the type
of effect. To edit and save a preset, turn the processor ON and follow
this example:
Example 2: Editing effect #21 and saving it:
1. Press preset button #1. The LED next to the button will light up.
2. Turn the PROGRAM knob until the display window shows "21."
3. Press the EDIT button. The EDIT LED will light up, along with
either the LEVEL or STYLE LED.
4. Press the #4 button to switch between LEVEL and STYLE (follow
the LEDs). To change how much of the effect is added to the sig-
nal, stop when the LEVEL LED is lit and turn the PROGRAM knob
to the desired setting (00 being "off" and 99 being maximum). To
change the effects parameter (in this case, the tap offset - see the
chart on the next page), press the #4 button until the STYLE LED
is lit, then turn the PROGRAM knob to the desired setting. You can
listen to the way the changes affect the sound by playing while
making the changes.
5. Press the EDIT button again. The EDIT LED will go out - the
changes have now been made and saved.
The next 4 pages show the program number, the name of the
effect, the parameter which can be changed and its upper and lower
limits for the GFX (pages 15 and 16) and BFX (pages 17 and 18).
G G
F F
X X
G G
F F
X X
i i
n n
g g
P P
r r
o o
g g
r r
a a
m m
i i
n n
g g
P P
r r
o o
g g
r r
a a
m m
n n
g g
a a
n n
d d
S S
a a
v v
i i
n n
g g
a a
n n
d d
S S
a a
v v
i i
/ /
B B
F F
X X
- -
1 1
0 0
0 0
0 0
/ /
B B
F F
X X
- -
1 1
0 0
0 0
0 0
s s
a a
s s
P P
r r
e e
s s
e e
t t
s s
a a
s s
P P
r r
e e
s s
e e
t t
n n
g g
P P
r r
o o
g g
r r
a a
m m
n n
g g
P P
r r
o o
g g
r r
a a
m m
s s
s s
s s
s s
Advertisement
