HP Kayak XW U3-W3 Installation Manual
Pc workstation
Hide thumbs
Also See for Kayak XW U3-W3:
- Handbook (31 pages) ,
- User manual (26 pages) ,
- Troubleshooting manual (23 pages)
Related Manuals for HP Kayak XW U3-W3
Summary of Contents for HP Kayak XW U3-W3
- Page 1 HP Kayak XW U3 & W3 PC Workstation— Installing Accessories In Your HP PC Workstation Explains in detail how to install accessories, such as extra memory, accessory boards, and additional disk drives.
-
Page 2: Supported Hp Accessories
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Supported HP Accessories Supported HP Accessories Internal Mass Storage Devices 5 Pairs of Rails for Front Access Devices: - 3.5-inch disk drive rails - 5.25-inch disk drive rails... -
Page 3: Removing And Replacing The Cover
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Removing and Replacing the Cover WARNING For your safety, never remove the PC Workstation’s cover without first removing the power cord from the power outlet, and any connection to a telecommunications network. - Page 4 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Removing and Replacing the Cover Replacing the Cover 1 Ensure that you have installed all your accessories and that all internal cables are properly connected and safely routed.
- Page 5 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Intrusion Monitor Your PC Workstation is equipped with an intrusion monitor, which is located on the front of the PC Workstation, behind the Hardware Control Panel.
-
Page 6: Moving The Power Supply
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Moving the Power Supply Moving the Power Supply 1 Disconnect the computer’s power cord and any telecommunications cable. 2 Remove the computer’s cover (refer to page 3). - Page 7 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation WARNING To avoid electrical shock, do not open the power supply. 6 Slide the power supply out of the computer until it stops—the power supply unit remains connected to the computer.
-
Page 8: Installing Memory
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Memory Installing Memory Main Memory Modules If you need more main memory to run your application software, you can install up to 1GB of memory in four DIMM slots. - Page 9 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 8 The location of the memory module slots is shown here. 9 Slide the memory module into the slot at 90° to the system board (with the cutouts furthest away from the processor).
-
Page 10: Installing Mass Storage Devices
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Installing Mass Storage Devices The computer has two internal shelves (for hard disk drives) and five front-access drive shelves (for front-access drives and hard disk drives). -
Page 11: Connecting Devices
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Connecting Devices If you add an IDE Zip drive, hard disk drive, CD-ROM drive, CD-RW drive, or tape drive, you need to connect it to power and data cables. - Page 12 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Which Power There are two different types of power connectors—these are shown below. Connectors to Use Some of the power connectors will already be connected to devices. If you install a device that requires a different connector, the connector converter should be supplied with the device.
- Page 13 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Disk Striping To achieve top performance through disk striping, a RAIDport provided on the system board aligned with PCI socket 3. When the Adaptec and RAIDport, the adapter sets up and accelerates disk striping on hard disks connected to the internal UltraWide 16-bit SCSI controller.
- Page 14 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Installing a Hard Disk Drive in an Internal Shelf CAUTION Hard disk drives larger than one inch (1”) in height can only be housed in the lower internal shelf.
- Page 15 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 7 Secure the drive with the four self-retaining screws. 8 Locate the appropriate data cable for the hard disk drive. Wide SCSI devices should be...
-
Page 16: Installing A Hard Disk Drive In A Front-Access Shelf
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices 9 Connect the power cable and the data cable to the rear of the drive. (The connectors are shaped to go in one way only.) Data Cable 10 Install any other accessories before completing the installation. - Page 17 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 7 Mount the drive on the tray as shown below. Set the drive on the tray 8 Slide the drive tray into the drive shelf and secure it.
- Page 18 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices 9 Locate the appropriate data cable for the disk drive. Wide SCSI devices should be connected to a free SCSI connector on the SCSI cable (you can add up to five SCSI devices).
-
Page 19: Completing The Installation Of A Hard Disk Drive
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Completing the Installation of a Hard Disk Drive When a SCSI Hard 1 Switch on the computer. Disk Drive Is Installed 2 To ensure compatibility, use the FDISK utility to delete any partitions on the new hard disk. - Page 20 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Before Installing an Refer to the drive’s installation guide to see if you must set jumpers or if there is a special installation procedure to follow.
- Page 21 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 8 Connect the data and power cables to the rear of the device. (The connectors are shaped to go in one way only.) Data Cable 9 Slide the power supply back into position, and tighten the four self- retaining screws.
- Page 22 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Mass Storage Devices Completing the Installation of a Drive When an IDE CD-ROM 1 Switch on the computer and press Drive Is Installed 2 In the Setup program, select the Advanced menu, the IDE Devices submenu.
-
Page 23: Installing Accessory Boards
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Accessory Boards CAUTION Static electricity can damage electronic components. Turn OFF all equipment. Don’t let your clothes touch the accessory. To equalize the static electricity, rest the accessory bag on top of the computer while you are removing the accessory from the bag. - Page 24 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing Accessory Boards 4 Unscrew and remove the slot cover. Store it in a safe place. If the slot cover is tight, loosen the screws on the adjacent slots.
- Page 25 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 7 Secure the board by replacing the slot cover screw. If you loosened the screws on adjacent slots, remember to tighten them. 8 Install any other accessories before replacing the cover (refer to page 4).
-
Page 26: Installing A Processor
HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing a Processor Installing a Processor Some operating systems support a second processor for enhanced performance. Contact your authorized reseller for up-to-date information. NOTE The Setup program provides an option to disable the second processor. - Page 27 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation 7 The system board has two processor sockets and a VRM slot for each processor. If you are changing the existing processor, remove it from the socket by squeezing the tabs at the top and bottom of the processor and gently pulling the processor away from the system board.
- Page 28 HP Kayak XW U3 & W3 PC Workstation — Installing Accessories In Your HP PC Workstation Installing a Processor Completing the 1 Verify that the system board bus speed switches are correctly configured for the processor. Installation of a Processor...