1. Manuals
  2. Brands
  3. Huck Manuals
  4. Tools
  5. HS24LH
  6. Instruction manual

Huck HS24LH Instruction Manual

Hydraulic installation tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
I
M
NSTRUCTION
ANUAL
HS24LH
H
I
T
YDRAULIC
NSTALLATION
OOL
Form HK 1024
04-22-2004

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HS24LH and is the answer not in the manual?

Questions and answers

Related Manuals for Huck HS24LH

Summary of Contents for Huck HS24LH

  • Page 1 NSTRUCTION ANUAL HS24LH YDRAULIC NSTALLATION Form HK 1024 04-22-2004...

  • Page 2: Eu Declaration Of Conformity

    (93/68/EEC) Council Directive related to EMC/EMI, (89/336/EEC) European Representative: Rob Pattenden, Huck International, Ltd. Unit C Stafford Park 7, Telford Shropshire TF3 3BQ, England, United Kingdom Authorized Signature/date: I, the undersigned, do hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).

  • Page 3: Contents

    13. Do not abuse tool by dropping or using it as a 2. Huck equipment must be maintained in a safe hammer. Never use hydraulic or air lines as a working condition at all times and inspected on a handle.

  • Page 4: Table Of Contents

    Tooling Alcoa Fastening Systems HS24LH ONTENTS EU D ......2 ECLARATION OF ONFORMITY ..........3 ONTENTS .
  • Page 5 Tooling Alcoa Fastening Systems HS24LH...

  • Page 6: Specifications

    Specifications. the tool and hoses. 2. Connect the Controller/Manifold to the POWERIG 7. The HS24LH tool comes with a 5/8” - 16mm anvil per Controller/Manifold instruction manual. and thimble installed on tool. (If these have been removed from the tool re-install at this time)

  • Page 7: Adjustment Of Switches

    Tooling Alcoa Fastening Systems HS24LH 5/8” & 16 DJUSTMENT OF SWITCHES Switches: Setting Limit Switch One: The HS24 tool uses two limit switches. Limit switch one Screw a fastener approximately .300in/7.5mm into the (LS-1) senses when the tool's actuator rod first touches thimble.

  • Page 8: Removing Anvil & Thimble

    Extend the hydraulic piston/anvil approximately. 3/8". With anvil removed, thread thimble into piston until it Place wrench Huck P/N: 126645 on the piston flats and a bottoms. Thread locking pin in until it bottoms, then back 1-11/16" wrench on anvil. Holding the piston, turn anvil to off 1/4 turn.
  • Page 9 Tooling Alcoa Fastening Systems HS24LH...
  • Page 10 Tooling Alcoa Fastening Systems HS24LH...
  • Page 11 Tooling Alcoa Fastening Systems HS24LH...
  • Page 12 Tooling Alcoa Fastening Systems HS24LH...
  • Page 13 Tooling Alcoa Fastening Systems HS24LH...
  • Page 14 Tooling Alcoa Fastening Systems HS24LH...
  • Page 15 Tooling Alcoa Fastening Systems HS24LH...
  • Page 16 Tooling Alcoa Fastening Systems HS24LH...

  • Page 17: Parts

    Tooling Alcoa Fastening Systems HS24LH ROUBLESHOOTING Always check the simplest possible cause of a 6. Tool operates erratically and fails to install fastener malfunction first. For example, a loose or disconnected properly. trigger line. Then proceed logically and eliminate each a.
  • Page 18 Tooling Alcoa Fastening Systems HS24LH ERVICE NOTES...

  • Page 19: Limited Warranties

    Huck shall not be liable for any loss or damage resulting tooling and fixtures that are not in good condition or repair from delays or nonfulfillment of orders owing to strikes, and suitable for their intended purpose.

  • Page 20: Locations

    The Future of Assembly Technology, The Future of Tooling to create any warranty, express, implied, or statutory; all warranties Technology, and Tools of Productivity are service marks of Huck are contained only in Huck’s written quotations, International. Huck provides technical assistance regarding the use acknowledgements, and/or purchase orders.

Table of Contents