Related Manuals for Huck 2624HS
Summary of Contents for Huck 2624HS
- Page 1 2624 2630 & serIes ydraulIc nstallatIon ools Makers of Huck , Marson , Recoil ® ® ® Brand Fasteners, Tools & Accessories June 14, 2016 HK1052...
- Page 2 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052)
-
Page 3: Table Of Contents
2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) ontents ec d . . . . . . . . . . . . . . . . . . . . . . . . . 2 eclaratIon of onforMIty . -
Page 4: S Afety I Nstructions
Avoid unsuitable postures, as it is likely for these not or your Huck representative. to allow counteracting of normal or unexpected tool 11. Only genuine Huck parts shall be used for replacements or movement. spares. Use of any other parts can result in tooling damage If the assembly power tool is fixed to a suspension device, or personal injury. - Page 5 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) afety nstruCtIons (continued) IV. REPETITIVE MOTION HAZARDS: VIII. VIBRATION HAZARDS: 1. When using assembly power tool, the operator can Exposure to vibration can cause disabling damage to the experience discomfort in the hands, arms, shoulders, neck nerves and blood supply to the hands and arms.
-
Page 6: Pecifications
• 2624 series: ® 2,600 psi (180 BAR) • 2630 series: HOSE KITS: Use only genuine HUCK Hose Kits rated @ PULL CAPACITY: 10,000 psi (689.5 BAR) working pressure. 30,356 lbs @ 6,500 psi (135.03 kN @ 448 BAR) • 2624 series: •... -
Page 7: P Rinciple Of O Peration
POWERIG to shut off, completing the cycle. reparatIon for POWER SOURCE CONNECTIONS WARNING: Use a Huck Powerig Hydraulic Unit, or equivalent, that has Read entire manual before using tool. been suitably prepared for operation. A 30-minute training session with qualified 1. -
Page 8: Aintenance
- Consult the Material Safety Data Sheet inspections of the system to detect minor troubles that can (MSDS) before servicing tool. be quickly and easily corrected. Huck recommends that you: - Keep foreign matter out of the hydraulic √ Inspect the tool and nose for external damage. -
Page 9: Isassembly
8. Models 2624, 2624-15, 2630, 2630RR: Remove the O-ring and Back-up ring from end cap. Igure Models 2624HS, 2624-PTD: Remove the O-ring and Back- up ring from front gland, and retaining ring, washer, polyseal, and wiper seal from end cap. -
Page 10: A Ssembly
11. Models 2624, 2624-15: Install locking disk, cover plate, and retaining ring. (Figure 8) • The appropriate Huck Spare Parts Service Kit: P/N 2624KIT Models 2624HS, 2624-PT, 2624PTD: Install locking disk, (2624, 2624-15), P/N 2624HSKIT (2624HS, 2624-PT, retainer, and screws. - Page 11 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) 2624 2624-15 & sseMbly rawIng 125691 500862 122769-2 128048 End Cap 125682 Front Gland Assembly Back-up GLYD Ring (contains Gland and O-Ring 500862 O-Ring components labeled Ring 125686 Piston Assembly 126108 507417...
-
Page 12: T Ool H Ead A Ssembly D Rawings
2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) 2624Hs 2624-pt & sseMbly rawIng 122769-2 128047 End Cap 125691 500862 125682 Front Gland GLYD Ring O-Ring Back-up 500862 O-Ring Ring 126108 127224 Piston 507417 125691 Back-up Ring... - Page 13 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) 2624ptd sseMbly rawIng 12804 7 End Cap 500862 O-Ring 125691 125682 Front Gland 500862 122769-2 131190 Barbed Retainer 125691 Back-up Ring Back-up O-Ring GLYD Ring 125683 Wiper Housing Ring 131084 Piston Guard 505894 Wiper Seal...
- Page 14 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) 2630 2630rr & sseMbly rawIng Igure 126959 Front Gland 501164 500869 O-Ring 126966 Back-up Cylinder Assembly 126958 Piston (2630) 126962 122769-4 506171 Ring 127274 Piston (2630RR) 128054 End Cap Wiper Housing GLYD Ring Polyseal...
-
Page 15: H Ydraulic H Ose A Ssembly D Rawing
2630, 2630RR - 2630KIT flexibility. Each Suspension Bracket Assembly contains the Bracket and Hardware shown below. sseMbly 2624 series 127400-2624 2624 & 2624HS Assembly Tool Kit - 123110-9 2630 series 127400-2630 Includes: (Fig. 3 & 6) Spacer - 123112-7 Locknut... -
Page 16: Roubleshooting
Improper tool operation. See Trouble 6. 3. Tool leaks hydraulic fluid. b . Scored anvil . a . Defective tool O-rings or loose hose Shear collar on Huck blind fastener not driven. connections at tool . a. Improper tool operation. 4. Hydraulic couplers leak fluid. -
Page 17: Ssembly Of
2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) nptf t sseMbly of Hreaded oMponents AIR FITTINGS ALL FITTINGS: 1) Apply TEFLON® stick to male threads which do 2) Tighten to finger-tight condition. not have pre-applied sealant per manufacturer’s 3) Wrench tighten to 2-3 turns past finger-tight condition. - Page 18 . and fixtures that are not in good condition or repair Huck shall not be liable for any loss or damage result- and suitable for their intended purpose . ing from delays or non-fulfillment of orders owing to...
- Page 19 2624 & 2630 Series Hydraulic Installation Tools Alcoa Fastening Systems & Rings (HK1052) ervICe otes...
- Page 20 International. Huck provides technical assistance acknowledgments, and/or purchase orders. It For the Long Haul ™ regarding the use and application of Huck fasten- is recommended that the user secure specific, ers and tooling. up-to-date data and information regarding each application and/or use of such products.
Need help?
Do you have a question about the 2624HS and is the answer not in the manual?
Questions and answers