Block Diagram; System Memory; Installing The Dimm Module - DFI CMS631-Q470E User Manual

Atx industrial
Hide thumbs Also See for CMS631-Q470E:
Table of Contents

Advertisement

X System Memory
JP4
USB7/8
2
4
1
+12V Power
PS2
1
5
8
5
2
6
JP2
1
5
2
6
JP3
1
5
VGA
2
6
COM 1
JP1
1
5
HDMI
DP++
LAN 2
USB3_1/2
USB2_1/2
LAN 1
USB3_3/4
USB2_3/4
Mic-in
Line-out
Line-in (opt.)
PCIe 1 (PCIe x16)
1
2
LAN LED
7
8
PCIe 2 (PCIe x4)
Front Audio
1
2
9
10
S/PDIF
1
2
6
1
5
JP23
1
Buzzer
1
1
10
2
1
1
1
1
1
1
11
Digital I/O
JP11/12/13/14/15
DIO
COM5
Power
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits from the memory channels. DIMMs are on the same
channel. DIMMs in a channel can be identical or completely different. However, we highly rec-
ommend using identical DIMMs. Not all slots need to be populated.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides
better system performance because it doubles the data transfer rate.
Features
Q470E: Four 288-pin Non-ECC UDIMM up to 128GB
H420E: Two 288-pin Non-ECC UDIMM up to 64GB
Dual Channel DDR4 2400/2666/2933MHz
User's Manual | CMS631
CPU FAN
DDR4_1
DDR4_3
System
1
1
Fan 1
Battery
14
13
Socket LGA1151
LPC
2
1
12
24
ATX Power
1
13
1
2
Front
Panel
11
1
SPI Flash
JP27
BIOS
M.2 M Key
10
USB2
1
2
11/12
DDR4_2
DDR4_4
PCI 1
SATA 0
SATA 1
(R0)
Intel
(R1)
1
10
USB2_5/6
SATA 2
SATA 3
USB3_5/6
(R2)
Q470E/H420E
(R3)
20
11
JP28
SATA 4
1
PCI 2
1
(R4)
1
CN37
JP26
6
PCI 3
1
M.2 M Key
1
JP24
SATA 5
(R5)
M.2 E Key
2230
9
PCI 4
(Opt.)
COM4
2
1
5
1
JP10
PCI 5
6
2
SDJ2
5
1
JP8
System Fan 2
6
2
1
5
1
JP6
2
10
6
2
2
2
2
5
1
JP7
1
1
9
1
9
1
9
1
9
6
2
COM6
USB2_
USB2_10
COM2
COM3
System Fan 3
9/14

System Memory

X

Installing the DIMM Module

Before installing the memory module, please make sure that the following safety cautions are
well-attended.
1. Make sure the PC and all other peripheral devices connected to it has been powered
down.
DDR4_1
DDR4_2
2. Disconnect all power cords and cables.
DDR4_3
3. Locate the DIMM socket on the system board
DDR4_4
4. Make sure the notch on memory card is aligned to the key on the socket.
Eject Tab
HARDWARE INSTALLATION
Memory Module
Notch
Socket Top View
Key
Eject Tab
Socket Side View
Chapter 2
9

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cms631-h420e

Table of Contents