Page 2
1. The changes or modifications not expressly approved by the party responsible for com- are the properties of the respective owners. pliance could void the user’s authority to operate the equipment. 2. Shielded interface cables must be used in order to comply with the emission limits. User's Manual | CMS632-W480E/Q470E...
Overview ..........................32 Main ............................33 Advanced ..........................33 RC ACPI Configuration ....................34 CPU Configuration ......................34 Power & Performance ....................35 PCH-FW Configuration ....................35 Trusted Computing ......................38 NCT6126D Super IO Configuration ................39 Serial Port Console Redirection ...................41 USB Configuration ......................42 User's Manual | CMS632-W480E/Q470E...
Page 4
• To reduce the risk of electric shock, unplug the power cord before removing the sys- tem chassis cover for installation or servicing. After installation or servicing, cover the system chassis before plugging the power cord. User's Manual | CMS632-W480E/Q470E...
Plug and Play peripherals. RTC Timer The Real Time Clock (RTC) installed on the system board allows your system to automatically power-on on the set date and time. User's Manual | CMS632-W480E/Q470E...
Colay vertical Type A SMBus USB 2.0 1x USB 2.0 LPC Header Vertical Type A TPM 2.0 (opt.) Super IO RS232/422/485 2x with WDT RS232 4x Fan Control PS/2 KB/MS H/W Monitor Case Open MECHANICAL DRAWING 233.68 227.33 User's Manual | CMS632-W480E/Q470E 227.33...
Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides better system performance because it doubles the data transfer rate. Features • Four 288-pin Non-ECC UDIMM up to 128GB (Core™ i5/i7 only support non-ECC) • Dual Channel DDR4 2400/2666/2933MHz (ECC support: W480E only) User's Manual | CMS632-W480E/Q470E...
Hold the card by its edges and remove it from the slot. The tabs snap automatically to the edges of the card and lock the card in place. Step 1 Step 1 Step 2 Step 2 Step 3 Step 3 User's Manual | CMS632-W480E/Q470E...
Align the 4 screw holes and tighten the heat sink up by inserting screws, DO remember to con- nect the fan cable on the board. (The location of fan connector may vary.) There are 4 screw holes around the CPU for the heat sink to be mounted. User's Manual | CMS632-W480E/Q470E...
2. Put a jumper cap on pin 2 and pin 3. Wait for a few seconds and set it back to its de- fault setting, i.e. jumper cap on pin 1 and pin 2. 3. Plug the power cord and power-on the system. 1-2 On: Normal (default) 2-3 On: Clear CMOS Data User's Manual | CMS632-W480E/Q470E...
JP2 must be set in accordance to JP3. When COM 2 RS232/422/485 is selected, JP6 and JP8 must be set in accordance to JP10. The pin functions of the COM ports will vary according to the jumpers’ setting. User's Manual | CMS632-W480E/Q470E...
JP4 (for COM 1) and JP7 (for COM 2) are used to configure Serial COM ports to pure RS232 or RS232 with power. The pin functions of COM 1 and COM 2 will vary according to JP4’s and JP7’s setting respectively. User's Manual | CMS632-W480E/Q470E...
JP15 is used to set DIO Power Voltage. JP11/12/13/14 is used to set DIO Power. JP11 (DIO 0~3 PWR) / JP12 (DIO 4~7 PWR) / JP13 (DIO 8~11 PWR) / JP14 (DIO 12~15 PWR) 1-2 On: 2-3 On: DIO PWR (default) User's Manual | CMS632-W480E/Q470E...
PCI 1 CN37 Buzzer SOJ2 M2JP2 JP26 M2JP3 Buzzer M2JP4 Power M2JP3 M2JP4 Power JP23 is used to set PWM control. JP27 is used to set InnoAGE functions. JP27 Pins Signals INNOAGE_PCRST# INNOAGE_RECOV# INNOAGE_PWRLED# INNOAGE_HDDLED# INNOAGE_PWRBTN# User's Manual | CMS632-W480E/Q470E...
M2JP1 and M2JP2 are used to control the power of M2CN1(M.2-M1) and M2CN2(M.2-M2). M2JP3 and M2JP4 are used to switch the signal output. M2JP3 M2JP4 1-2 On: 1-2 On: M2CN1 (PCIex4/SATA) M2CN2 (PCIex4) 2-3 On: 2-3 On: PCIE5 PCIE6 User's Manual | CMS632-W480E/Q470E...
RJ45 LAN 1/2 • 1 HDMI port • 1 VGA port • RJ45 LAN 1/2 • 1 Line-in jack (optional) • 1 Line-out jack • 1 Mic-in jack • 1 COM 1 • 4 USB 2.0 User's Manual | CMS632-W480E/Q470E...
4 x USB 2.0 rear ports (USB 7/8/9/10) • 2 x USB 3.2 Gen 2 internal ports (USB 5/6) • 2 x USB 2.0 internal ports, box headers (USB 11/12) • 1 x USB 2.0 internal ports, (USB 14) User's Manual | CMS632-W480E/Q470E...
VGA port. After you plug the monitor’s cable connector into the VGA port, gen- SIN- SIN- Data- tly tighten the cable screws to hold the connector in place. DTR- DTR- DSR- DSR- RTS- RTS- CTS- CTS- User's Manual | CMS632-W480E/Q470E...
Mic-in Jack (Pink) This jack is used to connect an external microphone. Front Audio The front audio connector allows you to connect to the second line-out and mic-in jacks that are at the front panel of your system. User's Manual | CMS632-W480E/Q470E...
Insufficient power supplied to the system may result in instability or malfunction of the add-in boards and peripherals. Calculating the system’s approximate power Control usage is important to ensure that the power supply meets the system’s consump- tion requirements. User's Manual | CMS632-W480E/Q470E...
Power On Suspend) state, it will blink at 1-second intervals. When the system is in the S3 (STR - Suspend To RAM) state, it will blink at 4-second intervals. Power Button This button is used to switch the system's power on or off . User's Manual | CMS632-W480E/Q470E...
33MHz LPC bus clock. For more information about LPC bus refer KDAT MDAT to the Intel Low Pin Count Interface Specification Revision 1.1’. The table below indicates the ® pin functions of the LPC connector. Assignment Assignment L_AD1 RST# L_AD0 FRAME# VCC3 LAD3 LAD2 SERIRQ 5V5B User's Manual | CMS632-W480E/Q470E...
Install PCI cards for other expansion demands. M.2 Socket The M.2 socket is the Next Generation Form Factor (NGFF) which is designed to support mul- tiple modules and make the M.2 more suitable in application for solid-state storage. User's Manual | CMS632-W480E/Q470E...
• There exists explosion hazard if the battery is incorrectly installed. the board when it’s correctly mounted. • Replace only with the same or equivalent type recommended by the manufacturer. • Dispose of used batteries according to local ordinances. User's Manual | CMS632-W480E/Q470E...
“Press DEL to run setup” will appear on the screen. If the message disappears before you respond, restart the system or press the “Reset” button. You may also restart the system by pressing the <Ctrl> <Alt> and <Del> keys simultaneously. User's Manual | CMS632-W480E/Q470E...
The time format is <hour>, <minute>, <second>. The time is based on the 24-hour military-time clock. For example, 1 p.m. is 13:00:00. Hour displays hours from 00 to 23. Minute displays min- utes from 00 to 59. Second displays seconds from 00 to 59. User's Manual | CMS632-W480E/Q470E...
Last State The system returns to the last state right before power failure. Note: Some of the fields may not be available when the features are not supported by the equipped CPU. User's Manual | CMS632-W480E/Q470E...
Enable or disable CPU Power Management. It allows CPU to enter "C states" when it’s idle and ME Unconfig on RTC Clear nothing is executing. When disabled, ME will not be unconfigured on RTC Clear. Note: The sub-menus are detailed in following sections. User's Manual | CMS632-W480E/Q470E...
Page 36
Version 2.22.1282. Copyright (C) 2022 AMI USB Provisioning of AMT Secure Erase Mode Enable or disable AMT USB Provisioning. Select Secure Erase module behavior: Simulated or Real. Force Secure Erase Enable or disable Force Secure Erase on next boot. User's Manual | CMS632-W480E/Q470E...
Page 37
This field is used to enable or disable the ME FW Image Re-Flash function, which allows the ration. user to update the ME firmware. Unconfigure ME Enable or disable to unconfigure ME with resetting MEBx password to default. User's Manual | CMS632-W480E/Q470E...
This field is used to enable or disable BIOS support for the security device such as an TPM 2.0 to achieve hardware-level security via cryptographic keys. Pending operation To clear the existing TPM encryption, select "TPM Clear" and restart the system. This field is not available when "Security Device Support" is disabled. User's Manual | CMS632-W480E/Q470E...
WatchDog Timer Unit Select WatchDog Timer Unit — Second or Minute. SuperIO WatchDog Timer Set SuperIO WatchDog Timer Timeout value. The range is from 0 (disabled) to 255. Note: The sub-menus are detailed in following sections. User's Manual | CMS632-W480E/Q470E...
Page 40
▼ SYS Smart Fan/CPU Smart Fan Control = [Disabled] Fix Fan Speed Count Set the fan speed, the value ranging from 1-100%, 100% being full speed. The fans will al- ways operate at the specified speed regardless of gauged temperatures. User's Manual | CMS632-W480E/Q470E...
Select parity bits: None, Even, Odd, Mark or Space. Stop Bits Select stop bits: 1 bit or 2 bits. Flow Control Select flow control type: None or Hardware RTS/CTS. Flow Control is for RS485 mode and is only supported by Serial Port 1 (COM1). User's Manual | CMS632-W480E/Q470E...
Keep USB devices available only for EFI applications. Auto Disable Legacy support if no USB devices are connected. XHCI Hand-off Enable or disable XHCI Hand-off. USB Mass Storage Driver Support Enable or disable USB Mass Storage Driver Support. User's Manual | CMS632-W480E/Q470E...
This field controls the execution of UEFI and Legacy Storage OpROM. Video This field controls the execution of UEFI and Legacy Video OpROM. Other PCI devices This field determines OpROM execution policy for devices other than Network, Storage or Video. User's Manual | CMS632-W480E/Q470E...
Set the wait time in seconds to press ESC key to abort the PXE boot. Use either +/- or numeric keys to set the value. Media detect count Set the number of times the presence of media will be checked. Use either +/- or numeric keys to set the value. User's Manual | CMS632-W480E/Q470E...
Please select a submenu and press Enter. The submenus are detailed in the following pages. Primary Display Select which of IGFX/PEG/PCI Graphics device to be the primary display. Internal Graphics Keep IGFX "Enabled" or "Disabled" based on the setup options, or select "Auto" for auto-detec- tion. User's Manual | CMS632-W480E/Q470E...
Enable or disable the root port, or select "Auto" for auto-detection. Enable or disable this field to detect non-compliance PCIe devices in the PEG. Max Link Speed Configure PCIE2/PCIE4 port’s Max Speed: Auto, Gen1, Gen2 or Gen3. User's Manual | CMS632-W480E/Q470E...
This field shows up when SATA Mode Selection is set to Intel RST Premium With Intel Optane System Acceleration. Enable or disable to use RST Legacy OROM when CSM is enabled. Ports and Hot Plug Enable or disable the Serial ATA port and its hot plug function. User's Manual | CMS632-W480E/Q470E...
Secure Boot. Press Enter and a prompt will show up for you to confirm. Reset To Setup Mode Clear the database from the NVRAM, including all the keys and signatures installed in the Key Management menu. Press Enter and a prompt will show up for you to confirm. User's Manual | CMS632-W480E/Q470E...
Refer to the Advanced > CSM Configuration submenu for more information. This field will appear only when a USB flash device is detected. Select this field to restore set- ting from the USB flash device. User's Manual | CMS632-W480E/Q470E...
When the BIOS IC needs to be replaced, you have to populate it properly onto the system board after the EEPROM programmer has been burned and follow the technical person's instructions to confirm that the MAC address should be burned or not. User's Manual | CMS632-W480E/Q470E...
Combination of RAID 0 (data striping) RAID 10 Stripe (not same mirror) and RAID 1 (mirroring) Extends capacity to the sum of total SPAN None drives, the second drive won't be used until the first one is full. User's Manual | CMS632-W480E/Q470E...
Page 53
2. Press <Y> to confirm the process. 5. Relevant information will appear with the message "Mode change is completed." on bot- tom. 3. Wait the process to start, the whole process takes about several seconds depends on the volume amounts. User's Manual | CMS632-W480E/Q470E...
Page 54
Chapter 4 Chapter 4 Chapter 4 RAID SETTINGS RAID SETTINGS RAID SETTINGS Other RAID modes follow the same procedure as well. User's Manual | CMS632-W480E/Q470E...