Before you begin ............................10 Preventing damage to your hardware ..................10 Step-by-step installation ........................10 Installing multiple cards ........................11 Connecting your QuadHead2Go Q185 card ............12 Before you begin ............................12 Connection overview ..........................12 Description of supported connectors ....................13 Step-by-step connection setup ......................13 Connecting your QuadHead2Go Q155 card ............
Page 3
Connecting your QuadHead2Go Q185 unit ............18 Before you begin ............................18 Connection overview ..........................18 QuadHead2Go Q185 – Back ....................18 Description of connectors ........................19 Step-by-step connection setup ......................19 Connecting your QuadHead2Go Q155 unit ............22 Before you begin ............................22 Connection overview ..........................22 QuadHead2Go Q155 –...
Page 4
QuadHead2Go Q155 card ......................35 QuadHead2Go Q185 unit ......................36 QuadHead2Go Q155 unit ......................37 External power supply ...........................38 Environmental ............................38 Appendix A – Matrox secure cable solution ............39 QuadHead2Go card ..........................39 Mini DisplayPort™ .........................39 Mini HDMI® ...........................40 QuadHead2Go unit ..........................41 Appendix B – Mounting your Matrox unit ............43 Mounting guidelines ..........................43...
Only use power supplies originally supplied with the product or use a replacement that’s approved by Matrox. Don’t use the power supply if it appears to be defective or has a damaged chassis. Matrox QuadHead2Go Series – User Guide...
Don’t attempt to open or repair a power supply unit (if one was supplied). Don’t attempt to open or repair your Matrox product. If there’s a fault with your Matrox product, review your Matrox warranty for more information. Matrox QuadHead2Go Series – User Guide...
Matrox rack mount kit * The hardware supplied with your Matrox product may vary depending on the SKU or part number of your product. For more information, contact your Matrox representative. † Only active adapters (sold separately) are supported. Passive adapters aren’t supported.
For information on how to use and configure Matrox PowerWall software, see the PowerWall help file. Be sure to check for any last-minute release notes included with your product. Also, check the Matrox web site (www.matrox.com/graphics) for the latest Matrox software, technical support, and product information.
Mini HDMI) and four (4) HDMI or Mini HDMI output connectors to allow you to receive a signal of up to 8K by 8K and output on up to four (4) HD HDMI monitors. Configuration guide For information on the possible display wall setups, see the Matrox QuadHead2Go Configuration Guide (www.matrox.com/quadhead2go/support). Before you begin...
Installing your QuadHead2Go card This section describes how to install your Matrox card. If your Matrox card is already installed in your system, skip to “Connecting your QuadHead2Go Q185 card”, page 12 “Connecting your QuadHead2Go Q155 card”, page 15. For information specific to your system, like how to remove its cover, see your system manual.
Secure the bracket of your Matrox card to the frame of your system. Your Matrox card is now installed. If you’re installing more than one card, see “Installing multiple cards”, page 11. Before restarting your system, connect your devices (see “Connecting your...
This section describes how to connect your Matrox QuadHead2Go Q185 card. Before you begin To avoid possible problems that could damage your monitors or prevent you from using your Matrox product, read the following guidelines before connecting your devices. ...
Connect a network cable to this connector. Note: To connect to the bracket of your Matrox product, the overmold (or boot) of the mini HDMI connectors must respect the maximum width (0.551 inches/14 mm) and thickness (0.331 inches/8.4 mm) stated in the HDMI specifications.
Page 14
Connect to your network Connect a network cable to the RJ-45 connector on your QuadHead2Go card. After connecting your QuadHead2Go card, validate your connection setup (see “Validating your QuadHead2Go setup”, page 25). Matrox QuadHead2Go Series – User Guide 14...
This section describes how to connect your Matrox QuadHead2Go Q155 card. Before you begin To avoid possible problems that could damage your monitors or prevent you from using your Matrox product, read the following guidelines before connecting your devices. ...
Connect a network cable to this connector. Note: To connect to the bracket of your Matrox product, the overmold (or boot) of the mini HDMI connectors must respect the maximum width (0.551 inches/14 mm) and thickness (0.331 inches/8.4 mm) stated in the HDMI specifications.
Page 17
Connect to your network Connect a network cable to the RJ-45 connector on your QuadHead2Go card. After connecting your QuadHead2Go card, validate your connection setup (see “Validating your QuadHead2Go setup”, page 25). 17 Matrox QuadHead2Go Series – User Guide...
This section describes how to connect your Matrox QuadHead2Go Q185 unit. Before you begin To avoid possible problems that could damage your monitors or prevent you from using your Matrox product, read the following guidelines before connecting your devices. ...
) is active (not black). For more information on LEDs, see “Description of status LEDs”, page DisplayPort IN Connect your DisplayPort cable to your Matrox unit. Connect the other end of the cable to your audio/video source. HDMI OUT Connect a digital monitor to this connector.
Page 20
WARNING: To avoid damaging the DisplayPort connector on your DisplayPort monitor cable or on your Matrox product, carefully remove the DisplayPort cable by pressing the latch on the top of the DisplayPort connector while removing the connector. Connect your digital monitors...
Page 21
After connecting your QuadHead2Go unit, validate your connection setup (see “Validating your QuadHead2Go setup”, page 25). 21 Matrox QuadHead2Go Series – User Guide...
This section describes how to connect your Matrox QuadHead2Go Q155 unit. Before you begin To avoid possible problems that could damage your monitors or prevent you from using your Matrox product, read the following guidelines before connecting your devices. ...
) is active (not black). For more information on LEDs, see “Description of status LEDs”, page HDMI IN Connect your HDMI cable to your Matrox unit. Connect the other end of the cable to your audio/video source. HDMI OUT Connect a digital monitor to this connector.
Page 24
After connecting your QuadHead2Go unit, validate your connection setup (see “Validating your QuadHead2Go setup”, page 25). Matrox QuadHead2Go Series – User Guide 24...
Description of status LEDs The LEDs on your QuadHead2Go products provides information to help you troubleshoot your Matrox product. The following describes the LED on your QuadHead2Go products. QuadHead2Go unit The two LEDS at the front of your QuadHead2Go unit provide power and status information.
Plug and Play) protocol. If your devices are in different network subnets, you need to validate network discovery in each subnet separately. For more information on using different subnets, contact your network administrator. After validating your connection setup, install your software. Matrox QuadHead2Go Series – User Guide 26...
Updating your Matrox QuadHead2Go firmware The Matrox QuadHead2Go Firmware Updater enables you to update the firmware and install the default layouts of your Matrox QuadHead2Go products. Note: Your Matrox QuadHead2Go product may ship with an older firmware version. Before using your QuadHead2Go product, you must update the firmware version installed on your devices to use the version of your deployed release.
QuadHead2Go devices using their IP address. To manually locate the devices, select , and Manual detection under enter the IP address Address or URL of each QuadHead2Go device you want to locate. Matrox QuadHead2Go Series – User Guide 28...
Page 29
Update the firmware When you’re done adding QuadHead2Go devices to the list of devices you want to update, click Update Wait while the devices are being updated. Updating devices may take up to10 minutes. 29 Matrox QuadHead2Go Series – User Guide...
Optimize visuals by cropping, upscaling, or downscaling the content as desired. This section describes how to install and use Matrox PowerWall software for Windows® Server® 2016, Windows® 10 Standard (64-bit), Windows® 10 Professional (64-bit), Windows® 10 Enterprise (64-bit), and Windows® 10 IoT.
Upload the configurations of the devices in your design to your physical QuadHead2Go devices. More information For more information on PowerWall software, see the help file included with your PowerWall software. 31 Matrox QuadHead2Go Series – User Guide...
Stop pressing the button to apply the current selection. Note: If LED B (right) turns to red when a button is pressed on your QuadHead2Go unit, the buttons on your unit are disabled. For more information, see “Description of status LEDs”. Matrox QuadHead2Go Series – User Guide 32...
Page 33
Gray gradient Select your layout. The selected layout is highlighted in the list. The available layouts depend on your firmware package and can be modified through Matrox PowerWall or the QuadHead2Go REST (Layout configuration) API. Shows the device information such as: ...
Regulatory compliance Class A: RCM, CE, FCC, KC * Custom resolutions are also supported. Please contact Matrox for more details. † When using a display resolution equal to or higher than 1280×720p60, we recommend you use certified HDMI cables that support your maximum resolution.
Regulatory compliance Class A: RCM, CE, FCC, KC * Custom resolutions are also supported. Please contact Matrox for more details. We recommend you use certified HDMI cables that support your maximum resolution. † When using a display resolution equal to or higher than 1280×720p60, we recommend you use certified HDMI cables that support your maximum resolution.
† When using a display resolution equal to or higher than 1280×720p60, we recommend you use certified HDMI cables that support your maximum resolution. ‡ Unless specified, modes are p60 (progressive 60 Hz). § Only use the power supply originally supplied by Matrox with your Matrox QuadHead2Go product. Matrox QuadHead2Go Series – User Guide 36...
Regulatory compliance Class A: RCM, CE, FCC, KC * Custom resolutions are also supported. Please contact Matrox for more details. We recommend you use certified HDMI cables that support your maximum resolution. † When using a display resolution equal to or higher than 1280×720p60, we recommend you use certified HDMI cables that support your maximum resolution.
12V DC, 3.5A Output connector DIN 4 male (4-pin) with lock Maximum power Note: Only use the power supply originally supplied by Matrox with your Matrox QuadHead2Go product. Environmental Temperature, operational 0 to 45 ºC (32 to 113 ºF) Temperature, non-operational -40 to 70 ºC (-40 to 158 ºF)
Make sure the ambient temperature doesn’t exceed the maximum recommended temperatures. For more information, see “Product information”, page Once your device is mounted, you can connect your system, monitors, and devices to your Matrox device. 43 Matrox QuadHead2Go Series – User Guide...
M3 flat-head screws (sold separately) to secure each device to the mounting shelf. The holes used to secure the device to the shelf differ depending on which side (left or right) the device is mounted. Matrox QuadHead2Go Series – User Guide 44...
Using your angled bracket kit You can mount your Matrox units on standard VESA mounts (75, 100, or 200 mm) or on the back of devices with VESA compliant mounting holes. To mount your Matrox unit on a VESA mount, you need two (2) angled brackets ...
Technical support Matrox values your business and offers professional support for your Matrox product. If you have a problem, we recommend you follow the procedure below for the quickest results. Contact your integrator – This is usually the quickest and most effective method of technical assistance.
An integrator or a manufacturer may also have directives regarding software updates. Directly from Matrox – A more recent software package may support more features and may offer increased capabilities (such as higher display resolutions). Matrox makes the latest display drivers, firmware, software, and system utilities available on the Matrox Technical Support Web site (www.matrox.com/graphics/en/support/drivers).
Page 48
FCC Compliance Statement Remark for the Matrox hardware products supported by this guide This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Page 49
Bitte wenden Sie sich an der Matrox-Website (www.matrox.com/environment/en/weee) für Recycling-Informationen. (Italiano) Informazioni per gli utenti europei – Direttiva sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE) Si prega di riferirsi al sito Web Matrox (www.matrox.com/environment/en/weee) per le informazioni di riciclaggio.