Cleaning Function; Before Running The Cleaning Function; Setting The Cleaning Function - Blaupunkt 5B27M7050 Instruction Manual

Table of Contents

Advertisement

Cleaning function

en
.Cleaning function
U se the "Self-cleaning" function to clean the cooking
C l e a n i n g f u n c t i o n
compartment.
You can choose from three cleaning cycles.
Cycle
Cleaning perfor-
mance
1
Gentle
2
Medium
3
Intensive
The dirtier the cooking compartment and the longer the
dirt has been there, the more powerful the cleaning
cycle should be. It is sufficient to clean the cooking
compartment every two to three months. You can clean
it more frequently if necessary. Cleaning requires
approx. 2.5-4.8 kilowatt hours.
Notes
For safety reasons, the appliance door locks
automatically once a certain temperature is reached.
You will not be able to open it again until the lock
symbol
on the display has gone out.
n
The interior lighting will not come on while the
appliance is being cleaned.
:
Warning
Risk of burns!
The cooking compartment becomes extremely hot
during the cleaning function. Never open the
appliance door. Allow the appliance to cool down.
Keep children away from the appliance.
The appliance will become very hot on the
;
Risk of burns!
outside during the cleaning function. Never touch the
appliance door. Allow the appliance to cool down.
Keep children away from the appliance.
:
Warning
Risk of harm to health!
The cleaning function heats up the cooking
compartment to a very high temperature so that food
remnants left over from roasting, grilling and baking will
burn off.This process releases vapours, which can
irritate the mucous membranes. While the cleaning
function is running, keep the kitchen well ventilated. Do
not remain in the room for long periods. Keep children
and pets away. Follow the instructions even when using
the Delayed start function with a delayed end time.

Before running the cleaning function

Make sure that the cooking compartment is empty.
Remove any accessories, cookware or shelf rails from
the cooking compartment. Please see the relevant
section for information on how to remove the rails.
~ "Rails" on page 21
Clean the appliance door and along the edges of the
cooking compartment in the area around the seal. Do
not scrub or remove the seal.
20
Length of cycle
Approx. 1 hour and 15 minutes
Approx. 1 hour and 30 minutes
Approx. 2 hours
:
Warning
Risk of fire!
Loose food remnants, fat and meat juices may catch
fire when the cleaning function is in progress. Before
you start the cleaning function, always remove the
worst of the food residues and remnants from the
cooking compartment.Do not use the cleaning
function for cleaning accessories.
The appliance will become very hot on the outside
Risk of fire!
during the cleaning function. Never hang
combustible objects, e.g. tea towels, on the door
handle. Do not place anything against the front of
the appliance. Keep children away from the
appliance.

Setting the cleaning function

Make sure you follow all the preparation instructions
before setting the cleaning function.
The length of time each cleaning cycle runs for has
been preset and cannot be changed.
Use the function selector to select the
1.
will be shown on the display panel.
A A
Use the temperature selector to set the cleaning
2.
setting.
Your chosen setting will be shown on the display
panel.
The cleaning function will start after a few seconds. The
programme will count down on the display panel.
Ventilate the kitchen while the self-cleaning function is
running.
The appliance door will lock shortly after the function
starts running. The
symbol will appear on the display
H
panel.
An audible signal will sound once the self-cleaning
cycle has finished.
:
‹‹
panel. Switch the appliance off by turning the function
selector to the "Off" position.
You will not be able to open the appliance door again
until the cooking compartment has cooled down
sufficiently and the lock symbol
gone out.
Setting a later end time
You can delay the end until later. Before starting, touch
and hold the
button until the end time symbol is
r
highlighted on the display panel. Use the
set a later end time.
The appliance will switch to standby after it is started.
function.
<
will appear on the display
‹‹
on the display has
H
selector to
}

Advertisement

Table of Contents
loading

Table of Contents