Related Manuals for Tatoma MT-7
Summary of Contents for Tatoma MT-7
- Page 1 USER’S MANUAL HORIZONTAL MIXER WAGON TATOMA AGRICULTURAL EQUIPMENTS CORP. 6238 HWY 412 COLCORD, OK 74338 918-422 4271 www.tatomausa.com...
- Page 2 ATTENTION! READ CAREFULLY THIS MANUAL BEFORE YOU START USING YOUR MIXER...
- Page 4 USER’S MANUAL MT-HORIZONTAL MIXERS INDEX 1. INTRODUCTION 2. DECLARATION OF CONFORMITY 3. REGISTRATION PLATE 4. RECEPTION AND IDENTIFICATION OF TRAILED MIXER 5. WARRANTY CONDITION 6. OPERATOR REQUIREMENTS 7. WARNINGS AND SAFETY REGULATIONS 8. MAINTENANCE INSTRUCTIONS 9. USE AND CONSERVATION OF THE INSTRUCTION MANUAL...
- Page 5 The serial number plate is located on the front-right-side of the tub. This number must be recorded in the Registration and Inspection Certificate in order to identify correctly your TATOMA mixer. Failure to read the manual, and assuming full knowledge of the machine by your side, may provoque an incorrect use of the machine, and this may lead to serious injury.
- Page 6 MT-HORIZONTAL MIXERS 2. “EC” DECLARATION OF CONFORMITY The company INGENIERIA Y MONTAJES MONZÓN S.L. Business address: Polígono industrial Las Paules 53-55 22400 Monzón (Huesca) España Declares sole responsibility that the towed mixer Models MT-7, MT-7-D, MT-10, MT-10-D, MT-13, MT-13-D, MT-16, MT-16-D...
- Page 7 USER’S MANUAL MT-HORIZONTAL MIXERS 3. “EC” REGISTRATION PLATE The following is an illustration of the EC plate. The plate is found on the front-right side, on the frame. SERIAL NUMBER CAN BE FOUND IN THIS PLATE, AT THE BOTTOM ROW “Nº DE BASTIDOR”.
- Page 8 USER’S MANUAL MT-HORIZONTAL MIXERS 4. RECEPTION AND IDENTIFICATION OF THE MIXER When you receive the mixer, the dealer, or personnel in charge, shall proceed as follows: - Check that the mixer is provided with the correct “user’s manual”. - Will ask you to read the “user’s manual” carefully, paying close attention to the safety regulations - Check that the mixer has not been damaged during transportation and is in good shape.
- Page 9 Complaints should be sent by written to the authorised dealer or directly to TATOMA depending on procedure. i) TATOMA reserves the right to verify if claims are covered by a warranty or not. j) Failures and / or damage caused to the mixer in the following cases will...
- Page 10 TATOMA reserves the right to modify the design and/or specifications of its products without prior notice. w) In the case of any doubts or legal claims, please contact your TATOMA dealer.
- Page 11 USER’S MANUAL MT-HORIZONTAL MIXERS 6. OPERATOR REQUIREMENTS The manipulation of this mixer is limited to competent and experienced operators. Anyone operating or working next to the mixer must use common sense. In order to be recognised as a qualified, the operator must also know and meet other requirements, such as;...
- Page 12 USER’S MANUAL MT-HORIZONTAL MIXERS 7. WARNINGS AND SAFETY REGULATIONS TAKE NOTE! This safety alert symbol that appears in this manual is used to call your attention about the instructions involving your personal safety, and the safety of others. Failure to follow these instructions can result in injury or death. Identify, correctly interpret and respect the warning signs placed in different points of the mixer, and identifying propperly the information and recommendations contained in this manual, contributes to avoiding accidents that can cause serious damage and injury...
- Page 13 USER’S MANUAL MT-HORIZONTAL MIXERS 7.1. DANGER AND WARNING SIGNS Safety symbols located in the machines Location Mixer’s side, next to the Attention! Danger, do not conveyor. open remove cover Rear and sides of the mixer, while the engine is in and next to the silo cutter operation group.
- Page 14 USER’S MANUAL MT-HORIZONTAL MIXERS Attention! Danger, close Rear of the mixer, where the the silo cutter cage when is silo cutter is located. not in use Attention! Check at all times proximity Rear and sides of the mixer, individuals in the silo cutter and next to the silo cutting work area...
- Page 15 • It is forbidden the user performs any operation with the mixer before reading the user’s manual and received relevant training by the dealer or TATOMA employees. • Respect the instructions contained in this manual, as well as the safety regulations and accident prevention norms contained in local regulations.
- Page 16 USER’S MANUAL MT-HORIZONTAL MIXERS • All drivers involved in using the machine must practice the mixing process by running the mixer empty, as well as the rest of related operations like loading and unloading, in order to become completelly familiar with them before using the mixer when loaded.
- Page 17 USER’S MANUAL MT-HORIZONTAL MIXERS protections with the chains to fixed parts of the tractor and the mixer. When PTO shaft is moving, the plastic protections must not move. • After the PTO connection operation is finished, unlock the parking brake, OR remove the parking chocks.
- Page 18 USER’S MANUAL MT-HORIZONTAL MIXERS Driving the mixer: • The mixer must be driven depending to the ground / road conditions. • Is forbidden to drive long distances with the silo cutter system up; • Keep a safe distance from ditches, waterways, slopes, etc., as the terrain may cause the overturn of the mixer and the tractor.
- Page 19 USER’S MANUAL MT-HORIZONTAL MIXERS Road transport: • Always comply with state and local laws related to the movement of farm machinery on public roads; • When driving on public roads with the mixer, please observe the local driving rules the rules at all times. •...
- Page 20 USER’S MANUAL MT-HORIZONTAL MIXERS • Before accessing the inside of the tub, as an additional security measure, disconnect the PTO shaft from the tractor. • It is strictly prohibited to incorporate devices into the mixer, which provide access to the tub with a height above the last step of the mixer ladder. •...
- Page 21 USER’S MANUAL MT-HORIZONTAL MIXERS • Make sure all moving parts of the accessories are completely stopped before performing any maintenance. • Always use a security system to block the tires, such as parking chocks. Never use a jack to support or sustain the machine while performing such work.
- Page 22 USER’S MANUAL MT-HORIZONTAL MIXERS • A first aid kit should always be available when carrying out maintenance work on the mixer. • When welding on the mixer, avoid current flowing through the ball bearings or rollers chains directly grounding the item being welded. •...
- Page 23 USER’S MANUAL MT-HORIZONTAL MIXERS 7.3. INSTRUCTIONS AND PRECAUTIONS DURING THE WORK Loading Instructions: • Visually inspect the mixing system before each load. • Never overload the mixer. The mixing capacity is determined by product weight. An overloaded mixer will not mix properly, and require more horse power from the tractor, so you could damage the mixer.
- Page 24 • When periodical maintenance works and parts repairs demand parts replacement, they will have to be done with genuine Tatoma parts, or parts that follow the specifications of the original parts. TATOMA does not assume any responsibility for the use of unauthorized parts and / or accessories that may cause damage as a result of their use.
- Page 25 USER’S MANUAL MT-HORIZONTAL MIXERS Lubrication table: TYPE OF COMOPONENT INTERVALS LUBRICANT Unloading Light oil Brush or spray lightly every 40 hours of operation. conveyor Bearings Quality grease Every 8 hours Every 8 hours. Transmission. Quality grease In each lubrication ensure PTO shaft comes out freely. PTO shaft.
- Page 26 USER’S MANUAL MT-HORIZONTAL MIXERS 8.1. AFTER WORK: • After operation, set the brakes, disconnect all power units, stop the engine and remove the keys from the ignition. • Store the mixer in an area away from human activity. • Do not park the mixer where it may be exposed to animals for long periods of time.
- Page 27 This manual should be kept in a safe place for future reference. The instruction manual must accompany the mixer at all times. In case of loss or damage, the user can contact TATOMA and request a new copy of this manual, specifying the serial number, model and year of manufacture of the mixer, data inscribed on the CE plate.
- Page 28 Health and Safety at Work. TATOMA declines all responsibility for damage or injury to people or material damage caused by non compliance of the regulations, warnings and indications...
- Page 29 USER’S MANUAL MT-HORIZONTAL MIXERS INSTRUCTIONS MANUAL...
-
Page 30: Table Of Contents
USER’S MANUAL MT HORIZONTAL MIXER WAGON. USER’S MANUAL MIXER DESCRIPTION 1.1. INTRODUCTION 1.2. USING THE MIXER 1.3. MAIN PARTS MIXER INSTRUMENTS AND CONTROLS 2.1. HITCH 2.2. POWER TAKEOFF 2.3. FRONT JACK 2.4. MIXER CONTROLS 2.5. LIGHTS AND SIGNALS 2.6. PARKING BRAKE 2.7. - Page 31 USER’S MANUAL MT HORIZONTAL MIXER WAGON. 4.9. UNLOADING BELT 4.10. HYDRAULIC SYSTEM 4.11. ELECTRIC SYSTEM 4.12. STOPPING THE MIXER FOR A PROLONGED TIME TECHNICAL CHARACTERISTICS OPTIONAL EQUIPMENT OPERATING IRREGULARITIES...
-
Page 32: Mixer Description
Warning! Technical data and characteristics of the trademark or model, of the different marketing materials or other components of the mixers cited in this manual are indicative. TATOMA reserves the right to modify the design or specifications without prior notice. -
Page 33: Main Parts
USER’S MANUAL MT HORIZONTAL MIXER WAGON. 1.3. MIXER MAIN PARTS The mixing system is of horizontal type, formed by a discontinuous auger, which is composed of : paddles, continuous augers, a lightened auger of plate and two beaters driven by hydraulic motors, within a triangular tub, open at the top. - Page 34 USER’S MANUAL MT HORIZONTAL MIXER WAGON. Mixer Components 1. Front jack 2. Controls 3. Unloading conveyor 4. Rear window 5. Tub 6. Beaters 7. Simple ladder 8. Parking hand brake 9. PTO (540) 10. Hitch 11. Battery (optional) 12. Hydraulic distributor / Solenoid valves block 13.
- Page 35 USER’S MANUAL MT HORIZONTAL MIXER WAGON. Mixer Components (Loading System) 16. Hydraulic loading arm 17. Protection grid 18. Silo cutter 19. Telescopic rear door Lever Arm and Cutter...
- Page 36 USER’S MANUAL MT HORIZONTAL MIXER WAGON. We describe here the main components depending on the different models. Loading System: The mixer can be supplied with a loading system (Silo cutter). It consists on the following components: Lever arm with silo cutter Lever arm (16): Made of a folding structural tube frame mounted on the front of the mixer.
- Page 37 USER’S MANUAL MT HORIZONTAL MIXER WAGON. Keep the steps clean and never jump from the steps to the ground. There is a risk of injury exists due to a possible slip or fall. Do not add any element, mechanism or system that allows access to the tub above the height of the last step on the ladder.
-
Page 38: Mixer Instruments And Controls
USER’S MANUAL MT HORIZONTAL MIXER WAGON. 2. MIXER INSTRUMENTS AND CONTROLS 2.1. HITCH The towed mixers can come equipped with the followed types of hitches: 1. 40/50 UNE swivel ring 2. 50/50 UNE fixed ring 3. Fish mouth (standard in the USA) 4. -
Page 39: Power Takeoff
USER’S MANUAL MT HORIZONTAL MIXER WAGON. 2.2. POWER TAKEOFF Towed mixers come equipped with a 540 power takeoff, completed with the adequate protective equipment. A PTO shaft is provided. As an option, it can be requested with a single or a double CV PTO shaft. Both types of PTO shaft can be provided with a fuse bolt. -
Page 40: Front Jack
USER’S MANUAL MT HORIZONTAL MIXER WAGONS 2.3. FRONT JACK The mixer is equipped with a front jack, that can be mechanical or hydraulic, that will help you to hook up the mixer to the tractor, as well will facilitate the parking of the mixer. In the case of the hydraulic front jack, it comes equipped with a control lever A control lever (P) attached to the side of the tub is used for operating the hydraulic jack. -
Page 41: Mixer Controls
USER’S MANUAL MT HORIZONTAL MIXER WAGONS Once the mixer is hooked up, raise the trailer jack to its upper limit to avoid hitting possible obstacles on the ground during operation. Parking the mixer: Park the mixer in a flat area, far away from furrows, channels, banks, and ditches, etc. Lower the jack until it makes contact with the ground. - Page 42 TATOMA declines all responsibility for accidents occurring as a result of non-compliance with the previous recommendations provided for mounting the control levers on the inside of the tractor cab.
- Page 43 Each control component (in accordance with the option), is marked with a label that indicates the function of each element. If these become deteriorated, the machine user can request new ones form the official dealer or directly from TATOMA. The adhesive labels that indicate the function of each hydraulic distributor and each mixer control must be kept in good condition and be changed if it becomes deteriorated.
- Page 44 USER’S MANUAL MT HORIZONTAL MIXER WAGONS Different tags are shown here. Note: The numbers in the upper left corner of each adhesive label are only used to identify them in this manual. They do not appear on the actual labels located below the distributors and control elements.
- Page 45 USER’S MANUAL MT HORIZONTAL MIXER WAGONS When using hydraulic distributor, the monoblock will be mounted as follows: Figure 2.12: Hydraulic Block Distribution Hydraulic Block with levers and cables control system 1. Silo cutter rotation motor distributor 2. Pressure gage for silo cutter rotation and arm lift 3.
-
Page 46: Lights And Signals
Unloading conveyor chain b. Unloading conveyor up and down c. Unloading door up and down d. Rear loading door 2.5. LIGHTS AND SIGNALS All TATOMA mixer wagons are fitted with triangular cathadrioptics, located in the back of the machine. - Page 47 USER’S MANUAL MT HORIZONTAL MIXER WAGONS On the silo cutter mixers, they are located in the cutter protection. As an option, all mixer models can be equipped with front reflectors, mounted on folding supports. If a certification to drive on the road is requested, the mixer will be mounted with the following elements: •...
-
Page 48: Parking Brake
USER’S MANUAL MT HORIZONTAL MIXER WAGONS Figure 2.16 Front Signals for Travelling on the Road 2.6. PARKING BRAKE Mixer wagons come provided with a couple of chocks. They come in supports attached to the side of the tub, completed with safety locks that hold the chocks when the mixer is moving. Chocks must be returned always to their holders after use. - Page 49 USER’S MANUAL MT HORIZONTAL MIXER WAGONS Figure 2.18 Parking Brake Once the mixer has been hooked up and, before beginning to work with the mixer, be sure the parking brake is unlocked. Driving with the parking brake on may cause breakdowns or blow out of the mixer tyres due to excessive overheating, provoking accidents.
-
Page 50: Battery
USER’S MANUAL MT HORIZONTAL MIXER WAGONS 2.7. BATTERY The battery is optional. It is found at the front of the mixer, and it is fastened into a box with a lid to protect it. In order to access the battery, remove the nuts and then remove the protective lid. The protective lid has an auxiliary electrical connection that is located on its left side, and it can be connected to the electric scale when loading is done without hitching the mixer to the tractor. -
Page 51: Weighing Scale
USER’S MANUAL MT HORIZONTAL MIXER WAGONS 2.8. WEIGHING SCALE Before manipulating the scales, please read the scales user’s manual provided with the mixer. The scale (1) is located on the front-right-hand side of the mixer. It is mounted inside a protective box (2) fitted with a polycarbonate front and an articulated mechanism that allows it to be turned to allow the visibility of the screen from different positions Figure 2.20 Electric Scale... -
Page 52: Back Loading Door
USER’S MANUAL MT HORIZONTAL MIXER WAGONS If the mixer has a battery kit option, the scales will be connected to it, and not to the tractor, so it will work all the time. This will allow to load the mixer without the need the mixer be hitched to the tractor. In order the scales work correctly, please consider the following recommendations: •... -
Page 53: Tractor And Mixer Hook-Up
USER’S MANUAL MT HORIZONTAL MIXER WAGONS It is strictly forbidden to add ingredients or correctors while the mixer is running. No matter which method is used to add ingredients, the person who is adding them must do so with the mixer stopped and the tractor keys in his or her possession. 2.10. - Page 54 USER’S MANUAL MT HORIZONTAL MIXER WAGONS Figure 2.26 Tripolar Connector List of poles: Warning! Respect polarity when • 15/30 : Positive connecting the female tripolar • 31 : Ground (Negative) connector to the battery • A: Reserve (Empty) Use care when connecting the female tripolar connector as there is a risk of electrical discharge if the two battery terminals touch simultaneously.
-
Page 55: Start Up
USER’S MANUAL MT HORIZONTAL MIXER WAGONS 3. USE OF THE MIXER Before using the mixer the operator should: • be well instructed on how to operate the mixer. • be informed about the dangers involved in the use of the mixer, and the safety measures to avoid them. - Page 56 TATOMA declines all liability for possible damages caused to persons or property arising from inadequate or non-existent rear-view mirrors.
- Page 57 USER’S MANUAL MT HORIZONTAL MIXER WAGON 10. Once the previously mentioned adjustments have been done, the operator should check up the following: ▪ the visibility from the tractor to the back part of the mixer is good, especially if the mixer is equipped with a silo cutter loading system.
- Page 58 USER’S MANUAL MT HORIZONTAL MIXER WAGON 3.2. LOADING THE MIXER The mixer will be loaded using front end loaders, or similar, by pouring the ingredients over the tub or using the silo cutter system. The mixer should be controlled by only one person, the tractor driver, who shall coordinate the actions of other people or machines should their intervention be necessary.
- Page 59 USER’S MANUAL MT HORIZONTAL MIXER WAGON The loading of ingredients through the silo cutter, should be done by following the next steps: The scales, located at the front of the mixer, will show the amount of product loaded in the mixer. It has to be consulted at all times during the loading process.
- Page 60 USER’S MANUAL MT HORIZONTAL MIXER WAGON Maximum Cutting Depth inches Corn silage Hay silage Grass silage Dry hay Table 3.1: Cutter Depth 6. In order to use the silo cutter correctly, adjust the lowering speed based on how hard the silage is, by turning the adjustment knob located on the monoblock distributor.
-
Page 61: Operation And Use Of The Beaters
USER’S MANUAL MT HORIZONTAL MIXER WAGON 3.3. OPERATION AND USE OF THE BEATERS The beaters are located on the inside of the tub on the right side of the mixer. Beaters Figure 3.4 Beaters The beaters are activated using the distributor indicated in section 2.5. Before starting the mix, make sure that beaters are activated so that the beaters are operated according to the previous figure in order to guarantee the correct circulation of the different ingredients. -
Page 62: Distribution Of The Mix
USER’S MANUAL MT HORIZONTAL MIXER WAGON If during the preparation of the mix more fibre than recommended is added, the machine will not work properly, provoking: a) absorption of excessive power. b) difficulty in mixing. c) Increase of the mixing time. d) overloading of the mixer leading to breakage According to what it has been said, the following rule is very important: DURING THE PREPARATION OF THE MIXTURE, MORE PRODUCTS MAY BE ADDED WHILE... - Page 63 USER’S MANUAL MT HORIZONTAL MIXER WAGON • Unloading Door (1): The door is activated by a hydraulic cylinder using the corresponding command. The unloading door has five different open positions, which permit increasing the quantity of the mix that passes to the unloading belt due to the auger’s rotating action. Figure 3.7 Door Graduation It is possible to know how open is the unloading door by the numbers 0 to 4 that can be seen from the tractor cabin.
- Page 64 USER’S MANUAL MT HORIZONTAL MIXER WAGON Before moving the mixer ensure that there is no one near by. 3.7. LOAD TEST Medium Load Test: We recommend that, when you are going to use the mixer for the first time, and in order to get use to the mixing system, and to use the mixer correctly, you do an initial mix using the 50% of the mixer’s capacity.
-
Page 65: Access To The Tub
USER’S MANUAL MT HORIZONTAL MIXER WAGON With this test we want to check the correct flowing of the product inside the tub, we want to practise the correct order when loading ingredients, and to be sure the operator understands the way the system works. Maximum load test When the medium load test is finished, and before unloading the mixer, we can load the mixer to its full capacity. -
Page 66: Mixer Maintenance
USER’S MANUAL MT HORIZONTAL MIXER WAGON Handle the mixer and tractor hook ups with heavy duty work gloves. To restart the mixer, the safety steps and recommendations indicated in section 3.1 of this instruction manual must be followed. 4. MIXER MAINTENANCE 4.1. - Page 67 Check tightness of the hydraulic hose clamps Every 3 months Electric System (See Section 4.11) Check the lighting and signalling system Weekly Check the scales Monthly Calibrate the scale (1) Yearly Table 4.1: User Operations (1) The scales should be calibrated by TATOMA. Page 49...
- Page 68 The maintenance of the mixer during the warranty period should be done by specialized personnel from TATOMA. The breach of this will mean the automatic loss of the warranty. The following maintenance operations should be performed exclusively by specialized technicians:...
- Page 69 USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.3. LEVEL CHECK Weekly check the oil levels of the multiplicator, auger reductor, and beater reductors through the level indicators. In general, if oil levels are low they should be refilled. The following should be taken into account: 1.
- Page 70 USER’S MANUAL MT HORIZONTAL MIXER WAGON Check the oil level through the plug (V), located in the side of the redactor. Remove the plug in order to check the oil level is full. If the oil level is low, fill the reservoir through the plug (L). In order to drain the oil, use the plug located at the bottom of the redactor.
- Page 71 USER’S MANUAL MT HORIZONTAL MIXER WAGON Figure 4.5: Gearbox Type 1 and 2 Hydraulic front jack Frequently check the hydraulic oil level using the indicator (TI) and refill if necessary. Drain the oil through the plug (Tv)When changing the oil use the drain plug (Tv). See Figure 4.6. Ap: Lever fitting (P) Tl: Oil fill plug Tv: Oil drain plug...
-
Page 72: Greasing
USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.4. GREASE All moving joints and drives should be cleaned and greased weekly through the greasers (See Fig. 4.11 and 4.12.). Figure 4.7: Grease Joint Greasers are identified with the above label. Do not exceed the lubrication, especially if a compressed air pump is used, to avoid damaging the bearing seals. - Page 73 USER’S MANUAL MT HORIZONTAL MIXER WAGON Mixer Grease Joints: Beater Side View 6. Hitch turning greaser 7. Mechanical front jack lift system 8. Planetary side auger support bearing Page 55...
- Page 74 USER’S MANUAL MT HORIZONTAL MIXER WAGON Trailer with Cutter 1. Cutter bearing (side opposite of motor) 2. Lever arm support 3. Upper support cutter lift cylinder (both sides) 4. Lower support cutter lift cylinder (both sides) 5. Rear loading door guides (both sides) Note: For the greasing of the rear support bearing of the auger it is necessary that the milling cutter is raised.
-
Page 75: Filters
USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.5. FILTERS Hydraulic Oil Filter Check Periodically check the clogging of the return filter (R) of the hydraulic oil, using the indicator gauge (M) located in the hydraulic oil tank. If the pressure gauge indicates a pressure of 0.8 Bar, replace the filter. This operation must be performed by qualified personnel. -
Page 76: Battery
USER’S MANUAL MT HORIZONTAL MIXER WAGON Weekly check the tyre pressure according to the following table. Model Tire Pressure (Bar) MT-7 10.0/75-15.3 18FR MT-10 12.5/80-15.3 MT-13 13.5/75-430.9 MT-16 15R22.5 MT-20 MT-25 445/65 R225 MT-5D 10.0/75-15.3 18FR MT-7D MT-10D 13.5/75-430.9 MT-13D MT-16D 15R22.5... -
Page 77: Loading And Mixing System
USER’S MANUAL MT HORIZONTAL MIXER WAGON Figure 4.13: Detailed View of Lighter Hook-up Keep the auxiliary connectors of the battery closed at all times, when not used. In case of breakdown, replacement or accident, handle the battery with caution as it contains sulfuric acid. - Page 78 USER’S MANUAL MT HORIZONTAL MIXER WAGON Changing Blades and Cleaning the Tub Check monthly the blades in the auger and the silo cutter. These blades should be checked monthly. Check the blades as follows: • Check that the blade bolts are tightened, replace blades that are missing or broken. •...
- Page 79 USER’S MANUAL MT HORIZONTAL MIXER WAGON Cutter: Figure 4.16: Cutter Blades In order to change the blades: Lift the silo cutter to a comfortable working height and stop the machine. Remove the screws. Turn over or substitute the blade depending on its condition. Tighten the screws.
-
Page 80: Unloading Belt
USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.9. UNLOADING BELT Cleaning the Unloading conveyor In order for the belt to unload correctly and with optimal performance, it should be completely unloaded each time it is used. To do this, close the unloading door and leave the belt running until no mix remains. Weekly, completely clean the unloading belt by removing its cover and removing the accumulated mix remains. -
Page 81: Hydraulic System
USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.10. HYDRAULIC SYSTEM Control Block Beaters General View Figure 4.20: Hydraulic System Page 63... -
Page 82: Electric System
USER’S MANUAL MT HORIZONTAL MIXER WAGON Besides checking the hydraulic oil level, other maintenance operations should be done: a) Visual, periodic review of possible oil leaks. b) Visual, periodic review of the hydraulic hoses, checking for possible points of wear. When a hydraulic hose is broken, or oil leaks are detected, the mixer must be automatically stopped, and must be checked by an specialist, as if the loss of hydraulic oil is , since if the level of the hydraulic oil tank is lowered excessively, overheating may occur, which would cause irreversible damage to the hydraulic... - Page 83 USER’S MANUAL MT HORIZONTAL MIXER WAGON 4.12 STOPPING THE MIXER FOR A LONG TIME If, for any reason, the mixer has to be stopped for a long period of time, it should be parked following the instructions in Section 3.9 of this manual. It is also advisable to periodically execute the following operations: •...
-
Page 84: Technical Characteristics
2,813 10,718 16,881 15R22.5 MT-20D left 33.5 1,474±134 10,182 3,617 13,397 18,354 * See diagrams on following pages All data and descriptions are solely indicative. TATOMA reserves the right to modify the design or specifications without prior notice. Page 61... - Page 85 3 / 4 Main Dimensions Cutter Cutter Model width Height (inches) (inches) (inches) (inches) (inches) (inches) Silo Cutter Mixers ( with or without self loading shovel MT-7 MT-10 MT-13 shown. shown. MT-16 MT-20 MT-25 Silo Cutter Mixers MT-7D MT-10D MT-13D MT-16D MT-20D...
- Page 86 USER’S MANUAL MT HORIZONTAL MIXER WAGON MIXERS GENERAL DIMENSIONS (with or without self loading shovel) SILO CUTTER MIXER GENERAL DIMENSIONS...
-
Page 87: Optional Equipment
USER’S MANUAL MT HORIZONTAL MIXER WAGON 6. OPTIONAL EQUIPMENT Weighing System Programmable weighing system Programmable weighing system with data transfer Weighing system printer Remote display Loading, mixing and unloading System Double fixed unloading belt Folding unloading belt Folding double unloading belt Increase cutter power Other equipment Hydraulic trailer jack... - Page 88 USER’S MANUAL MT HORIZONTAL MIXER WAGON. 7. MALFUNCTIONS Repairs should be performed by qualified technical personnel. Before starting any work you should study and consider the following steps. It will be necessary to consult all the available documentation: diagrams, drawings, etc., and once the problem has been detected, determine which parts of the mixer must be disassembled and in what order.
- Page 89 USER’S MANUAL MT HORIZONTAL MIXER WAGON. Incident Possible cause Repairs LIGHTING - blown tractor fuse - Change fuse. Faster turn signal frequency. - Change bulb. - defective bulb - Change fuse. - blown tractor fuse - Change bulb. - defective bulb Lights do not work - Connect and verify the wire.
- Page 90 USER’S MANUAL MT HORIZONTAL MIXER WAGON. Incident Possible cause Repairs - Jam due to product accumulation or foreign - Detect the affected part and call a qualified Auger does not work objects technician. Beaters do not work - No pump pressure - Check pressure and change pump if necessary.