Subscribe to Our Youtube Channel
Related Manuals for ELTEX WOP-12ac
Summary of Contents for ELTEX WOP-12ac
- Page 1 Wireless access point WOP-12ac Quick guide Firmware version 1.22.2 IP address: 192.168.1.10 Username: admin Password: password...
-
Page 2: Table Of Contents
WOP-12ac. Quick guide Contents Annotation...........................3 Connecting to the web interface....................4 Configuration of WOP-12ac network parameters ..............5 WOP-12ac firmware upgrade....................6 SNMP service configuration......................7 Wireless interfaces configuration ....................8 Virtual access points configuration ..................10 Monitoring main parameters of wireless network ..............12 Cluster operation mode......................14 Description ..........................14... -
Page 3: Annotation
WOP-12ac. Quick guide 1 Annotation This manual specifies the following: • connection to WOP-12ac web interface; • configuration of WOP-12ac network parameters; • WOP-12ac firmware update; • SNMP configuration; • wireless interfaces configuration (operation mode, band); • virtual access points configuration;... -
Page 4: Connecting To The Web Interface
WOP-12ac. Quick guide 2 Connecting to the web interface Connect network cable to the PoE interface of the access point and to the PoE switch/injector. Next, connect a PC to the injector or switch. Open a web browser, for example, Firefox, Opera, Chrome. -
Page 5: Configuration Of Wop-12Ac Network Parameters
WOP-12ac. Quick guide 3 Configuration of WOP-12ac network parameters For remote management of WOP-12ac, set network parameters of the device according to the settings of the network that you intend to use. In the Manage menu, open Ethernet Settings tab and perform the following: •... -
Page 6: Wop-12Ac Firmware Upgrade
WOP-12ac. Quick guide 4 WOP-12ac firmware upgrade For correct operation of WOP-12ac, it is recommended to upgrade the firmware to the latest version. The relevance of the version installed on the device can be clarified on the official website of the manufacturer in the Download Center section or by contacting the manufacturer directly. -
Page 7: Snmp Service Configuration
WOP-12ac. Quick guide 5 SNMP service configuration SNMP service configuration is performed in the SNMP section of the Services menu. • Restrict the source of SNMP requests to only the designated hosts or subnets – check Enabled box. • Hostname, address, or subnet of Network Management System – specify an IP-address of SNMP server, from which SNMP commands will be transmitted. -
Page 8: Wireless Interfaces Configuration
WOP-12ac. Quick guide 6 Wireless interfaces configuration WOP-12ac has 2 radio interfaces which are capable to operate simultaneously (Radio 1 and Radio 2). Each interface is capable to operate on its frequency band in different wireless network modes. Radio 1 operates at 5 GHz band, Radio 2 –... - Page 9 WOP-12ac. Quick guide In the Manage menu, open the Radio tab and perform the following: Configuring Radio 1: • Radio – select the configured interface. Select 1; • Channel Bandwidth – set 80 MHz. To apply a new configuration and save setting to non-volatile memory of the access point, click Update.
-
Page 10: Virtual Access Points Configuration
WOP-12ac. Quick guide 7 Virtual access points configuration On each wireless interface, up to 16 virtual access points can be configured. Each access point may have individual name of wireless network (SSID) and type of authentication/authorization. According to the network scheme given in the figure 1, it is necessary to configure 2 virtual access points on Radio 1 and Radio 2. - Page 11 WOP-12ac. Quick guide Configuration of VAP on Radio 2 is performed the same way. Select value 2 in Radio and perform the configuration as for the Radio 1 (given above). The password for “Work Network” SSID should be the same for both VAP Radio 1 and VAP Radio 2. ...
-
Page 12: Monitoring Main Parameters Of Wireless Network
WOP-12ac. Quick guide 8 Monitoring main parameters of wireless network The list of connected users can viewed in the Client Association tab of the Status menu. Clicking on the client's MAC address reveals detailed information about the client operation and statistics on packet transmission. - Page 13 WOP-12ac. Quick guide The list of events is given in the Events tab of the Status menu. Redirection of events to a third-party SYSLOG server can be configured here as well.
-
Page 14: Cluster Operation Mode
If the devices with these parameters are not found, WOP-12ac becomes a master of the cluster. If the devices belonging to the cluster are found, WOP-12ac starts copying the configuration of a master. Thus, the first device with enabled Cluster mode occurred on the network becomes a master of its cluster. Other devices occurred on the network later and having the same cluster name start duplicating the master configuration. -
Page 15: Cluster Configuration
• Location – specify physical location of the access point. The option is used to analyze and control the network in different monitoring tables. “Eltex” is used in the example; • Cluster Name – set cluster name. The access point will be connected only to a cluster, which name is specified in “Cluster Name”. - Page 16 WOP-12ac. Quick guide In the Single IP Management menu, perform the following configuration: • Cluster Management Address – specify unique IPv4 address via which the device may access the master cluster. The master should be located in the same subnet with the cluster and not match IP address of other devices.
-
Page 17: Monitoring
WOP-12ac. Quick guide 9.4 Monitoring To view sessions parameters of clients connected to the access points of given cluster, switch to the Sessions tab. Clients are defined through MAC addresses and an access points which they are connected to. To view the statistics, select necessary value and click Go in the Display section. The following parameters might be viewed: •... - Page 18 WOP-12ac. Quick guide According to this table, spectral analysis of the whole network might be carried out and there is an opportunity to estimate interference influence to each access point. This will allow assessing the correct location of access points across the coverage area and indicating problem areas in which the level of interference may interfere with the quality of services.
- Page 19 WOP-12ac. Quick guide The Proposed Channel Assignments table contains data on available channel values, which the radio interface will switch to if optimal channel selection has been launched: • IP Address – IP address of the access point in the cluster;...
-
Page 20: Firmware Upgrade
WOP-12ac. Quick guide 9.5 Firmware upgrade The operation in the cluster mode allows performing automatic firmware update for all the access points in the cluster without using external systems or controllers. Firmware update might be performed: • through web interface;... - Page 21 Place the "wop12.manifest” file on TFTP server, the file should contain the following string: VERSION= "1.22.X.X" WOP-12ac-1.22.X.X.tar.gz, where WOP-12ac-1.22.X.X.tar.gz is a name of the archive containing firmware for WOP-12ac; 1.22.X.X is a firmware version included to the archive. The firmware version can be viewed in “version”...
- Page 22 Service Center of the company: http://www.eltex-co.com/support You are welcome to visit Eltex official website to get the relevant technical documentation and software, to use our knowledge base or consult a Service Center Specialist in our technical forum. http://www.eltex-co.com/ http://www.eltex-co.com/support/downloads/...
Need help?
Do you have a question about the WOP-12ac and is the answer not in the manual?
Questions and answers