ELTEX WEP-2ac Quick Manual
Hide thumbs
Also See for WEP-2ac:
- User manual (19 pages) ,
- Quick manual (22 pages) ,
- User manual (17 pages)
Subscribe to Our Youtube Channel
Related Manuals for ELTEX WEP-2ac
Summary of Contents for ELTEX WEP-2ac
- Page 1 Wireless access point WEP-2ac, WEP-2ac Smart Quick guide Firmware version 1.23.0 IP address: 192.168.1.10 Username: admin Password: password...
-
Page 2: Table Of Contents
WEP-2ac, WEP-2ac Smart. Quick guide Contents Annotation..........................3 Installation order ........................4 Safety rules..........................4 Installation recommendations....................4 Device installation........................5 2.3.1 Wall mounting ........................5 2.3.2 Installing to false ceiling ..................... 6 2.3.3 Removing the device from the bracket................6 2.3.4 RJ-45 pinout ........................7 Connecting to the web interface....................8... -
Page 3: Annotation
WEP-2ac, WEP-2ac Smart. Quick guide 1 Annotation This manual contains the following information: • connection to WEP-2ac web interface; • configuration of WEP-2ac network parameters; • WEP-2ac firmware update; • SNMP configuration; • wireless interfaces configuration (operation mode, band);... -
Page 4: Installation Order
WEP-2ac, WEP-2ac Smart. Quick guide 2 Installation order This section defines safety rules, installation recommendations, setup procedure and the device starting procedure. 2.1 Safety rules Do not install the device close to heat sources or in rooms with temperature below 5 °C or above 40 °C. -
Page 5: Device Installation
WEP-2ac, WEP-2ac Smart. Quick guide 2.3 Device installation The device should be attached to plain surface (wall or ceiling) in accordance with the safety instruction and recommendations listed above. The device delivery package includes required mounting kit to attach the device to plain surface. -
Page 6: Installing To False Ceiling
WEP-2ac, WEP-2ac Smart. Quick guide 2.3.2 Installing to false ceiling It is not recommended to place the device inside a false ceiling as metal frame causes multipath signal propagation and signal attenuation. 1 – metal bracket; 2 – Armstrong panel; 3 – plastic bracket; 4 – device. -
Page 7: Pinout
WEP-2ac, WEP-2ac Smart. Quick guide 2.3.4 RJ-45 pinout The next scheme is used for twisted-pair wiring. RJ-45 connector Side A: white orange; orange; white green; blue; white blue; green; white brown; brown. -
Page 8: Connecting To The Web Interface
WEP-2ac, WEP-2ac Smart. Quick guide 3 Connecting to the web interface Connect network cable to the PoE interface of the access point and to the PoE switch/injector. Next, connect a PC to the injector or switch. Open a web browser, for example, Firefox, Opera, Chrome. -
Page 9: Configuring Network Parameters
IP addresses and other network parameters to access points via the DHCP protocol, set the Connection Type field to 'DHCP' and this will complete the configuration of the network part; • Static IP Address – specify the IP address of WEP-2ac. In the given example, VLAN 10 address is 192.168.40.26; •... -
Page 10: Firmware Upgrade
WEP-2ac, WEP-2ac Smart. Quick guide 5 Firmware upgrade For correct operation of WEP-2ac and WEP-2ac Smart, it is recommended to update the firmware to the latest version. The relevance of the version installed on the device can be clarified on the official website of the manufacturer in the Download Center section or by contacting the manufacturer directly. -
Page 11: Configuring The Snmp Service
Host name or IP or IPv6 Address – check one of the fields for specifying traps receiver address and enter an IP address of the device to which WEP-2ac will send traps. In the given example, IP address to receive SNMP traps is 172.16.0.22. -
Page 12: Configuring Wireless Interfaces
WEP-2ac, WEP-2ac Smart. Quick guide 7 Configuring wireless interfaces WEP-2ac and WEP-2ac Smart have 2 radio interfaces (Radio1 and Radio 2) that are capable to operate simultaneously. Radio 1 operates at 5 GHz band, Radio 2 – at 2.4 GHz. - Page 13 WEP-2ac, WEP-2ac Smart. Quick guide In the Manage menu, open the Radio tab and perform the following: Configuring Radio 1: • Radio – select value 1; • Channel Bandwidth – set value 80 MHz; To apply a new configuration and save setting to non-volatile memory of the access point, click Update.
-
Page 14: Configuring Virtual Access Points
WEP-2ac, WEP-2ac Smart. Quick guide 8 Configuring virtual access points On each wireless interface, up to 16 virtual access points can be configured. Each access point may have individual name of wireless network (SSID) and type of authentication/authorization. According to the network... - Page 15 WEP-2ac, WEP-2ac Smart. Quick guide Configuration of Radio 2 is performed the same way. Select 2 value in Radio and perform the configuration as for the Radio 1 (given above). The password for 'Work Network' SSID should be the same for both VAP Radio 1 and VAP Radio 2. ...
-
Page 16: Monitoring Of The General Wireless Network Parameters
WEP-2ac, WEP-2ac Smart. Quick guide 9 Monitoring of the general wireless network parameters All clients connected to this access point can be viewed in the Status menu of the Client Associations tab. Clicking on the client's MAC address reveals detailed information about the client's operation and statistics on packet transmission. - Page 17 WEP-2ac, WEP-2ac Smart. Quick guide For more detailed information, it is recommended to read the complete user manual.
-
Page 18: Cluster Operating Mode
The default name of a cluster is default. After loading, WEP-2ac defines if there are devices located on the network with the same name as in its configuration. If the devices with these parameters are not found, WEP-2ac becomes a master of the cluster. If the devices belonging to the cluster are found, WEP-2ac starts copying the configuration of a master. -
Page 19: Configuring Cluster
WEP-2ac, WEP-2ac Smart. Quick guide 10.2 Configuring Cluster The device can work in a cluster only if WDS (Wireless Distribution System) and WGB (Work Group Bridge) are disabled. To work in a Management cluster, the Ethernet interface of all points must be within the same network. - Page 20 WEP-2ac, WEP-2ac Smart. Quick guide In the Single IP Management menu, perform the following configuration: • Cluster Management Address – unique IPv4 address, at which the cluster master point will be available. This address must be on the cluster subnet and not be the same as the IP address of other devices on the network.
-
Page 21: Monitoring
WEP-2ac, WEP-2ac Smart. Quick guide 11 Monitoring In the Sessions submenu, the parameters of client sessions connected to access points located in the cluster can be viewed. Each client is identified by the MAC address and access point to which it is currently connected. - Page 22 WEP-2ac, WEP-2ac Smart. Quick guide Based on this table, a spectral analysis of the entire network can be performed, and the impact of interference on each access point can be evaluated. This will enable the assessment of the correct location of access points across the coverage area and identification of problem areas where the level of interference may affect the quality of services.
-
Page 23: Cluster Firmware Upgrade
WEP-2ac, WEP-2ac Smart. Quick guide 11.1 Cluster firmware upgrade The operation in the cluster mode allows performing automatic firmware upgrade for all the access points in the cluster without using external systems or controllers. Firmware upgrade might be performed: •... -
Page 24: Firmware Upgrade Via Dhcp Autoprovisioning
Place the 'wep2.manifest' file on TFTP server, the file should contain the following string: VERSION= '1.22.X.X' WEP-2ac-1.22.X.X.tar.gz, where WEP-2ac-1.22.X.X.tar.gz is a name of the archive containing firmware for WEP-2ac; 1.22.X.X is a firmware version included to the archive. The firmware version can be viewed in 'version' file in firmware archive. - Page 25 Service Center of the company: http://www.eltex-co.com/support You are welcome to visit Eltex official website to get the relevant technical documentation and software, to use our knowledge base or consult a Service Center Specialist in our technical forum. http://www.eltex-co.com/ http://www.eltex-co.com/support/downloads/...
Need help?
Do you have a question about the WEP-2ac and is the answer not in the manual?
Questions and answers