ELTEX WEP-2ac User Manual
Hide thumbs
Also See for WEP-2ac:
- Quick manual (25 pages) ,
- User manual (19 pages) ,
- User manual (19 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for ELTEX WEP-2ac
Summary of Contents for ELTEX WEP-2ac
- Page 1 Wireless access point WEP-2ac, WEP-2ac Smart User manual Firmware version 1.15.0 IP address: 192.168.1.10 Username: admin Password: password...
-
Page 2: Table Of Contents
Wall mounting ...........................12 3.5.2 Mounting to a false ceiling .......................13 3.5.3 Removing the device from the bracket....................13 Application A. Anntenna patterns of WEP-2ас and WEP-2ac Smart ............14 Application B. Connectors pin array .......................15 The list of changes ..........................16 2... -
Page 3: Introduction
WEP-2ac and WEP-2ac Smart are Wi-Fi access points of the Enterprise class. The devices are dedicated to be installed inside buildings as access points and to create a seamless wireless network using several identical access points on a large area. -
Page 4: Device Description
The devices are dedicated to create L2 wireless networks interfacing with a wired network. WEP-2ac and WEP-2ac Smart are connected to a wired network via 10/100/1000M Ethernet interface and arrange high-speed access to the Internet for devices supporting Wi-Fi technology at 2.4 and 5 GHz. - Page 5 • Changing WMM parameters for each radio interface. Security • E-mail notification on system events; • Centralized authorization via RADIUS server (WPA Enterprise); • WPA/WPA2; • Captive Portal; • Support for Internet Protocol Security (IPsec) The figure below illustrates an application scheme of WEP-2ac. ...
-
Page 6: Technical Parameters Of The Devices
WEP-2ac, WEP-2ac Smart user manual 2.3 Technical parameters of the devices WAN Ethernet interface parameters Number of ports Connector RJ-45 Data rate, Mbps 10/100/1000, auto-negotiation Standards BASE-T Parameters of the wireless interface Standards 802.11a/b/g/n/ac Frequency range, MHz 2400–2483.5 MHz, 5150–5850 MHz... -
Page 7: Design
2.4.1 Main panel of the devices The figure below shows a layout of WEP-2ac and WEP-2ac Smart main panel: The following light indicators, connectors and controls are located on the main panel of WEP-2ac, WEP-2ac Smart: Main panel element Description... -
Page 8: Light Indication
WEP-2ac, WEP-2ac Smart user manual 2.5 Light indication The Wi-Fi, LAN and power indicators show the device current state. The table below lists possible status of the LEDs. LED state Device state Wi-Fi (5) green LED glows constantly Wi-Fi is enabled... -
Page 9: Installation Rules
Approximate radius of coverage area of WEP-2ac with a good-quality signal in case of mounting on a ceiling in typical office: 40-50 m at 2.4 GHz and 20-30 m at 5 GHz. In case of no obstacles, the radius of the coverage area is up to 100 m at 2.4 GHz and up to 60 m at 5 GHz. ... -
Page 10: Channel Selection For Neighboring Access Points
WEP-2ac, WEP-2ac Smart user manual Material Change of signal level, dB 2.4 GHz 5 GHz Organic glass -0.3 -0.9 Brick -4.5 -14.6 Glass -0.5 -1.7 Plaster slab -0.5 -0.8 Wood laminated plastic -1.6 -1.9 Plywood -1.9 -1.8 Plaster with wirecloth -14.8... -
Page 11: Wep-2Ac, Wep-2Ac Smart Installation
WEP-2ac, WEP-2ac Smart user manual Scheme of channel allocation among neighboring access points in the frequency range of 2.4 GHz when channel width is 20 MHz • It is recommended to save the same allocation scheme between floors, see the figure below: ... -
Page 12: Wall Mounting
WEP-2ac, WEP-2ac Smart user manual 3.5.1 Wall mounting 1. Fix the bracket (included in the delivery package) to the wall: Attaching the bracket to a wall a. The figure shows the bracket allocation. b. Pass the wires into the corresponding grooves on the bracket while installing the bracket. -
Page 13: Mounting To A False Ceiling
WEP-2ac, WEP-2ac Smart user manual 3.5.2 Mounting to a false ceiling It is not recommended to place the device inside a false ceiling as metal frame causes multipath signal propagation and signal attenuation. 1 – metal bracket; 2 – armstrong panel;... -
Page 14: Application A. Anntenna Patterns Of Wep-2Ас And Wep-2Ac Smart
WEP-2ac, WEP-2ac Smart user manual 4 Application A. Anntenna patterns of WEP-2ас and WEP-2ac Smart 2.4 GHz range 5 GHz range... -
Page 15: Application B. Connectors Pin Array
WEP-2ac, WEP-2ac Smart user manual 5 Application B. Connectors pin array RJ-45 pin array The following scheme is used in case of connection via twisted-pair wire. Side А: 1. white-orange; 2. orange; 3. white-green; 4. blue; 5. white-blue; 6. green;... -
Page 16: The List Of Changes
WEP-2ac, WEP-2ac Smart user manual 6 The list of changes Document's version Date of issue Changes Version 1.8 30.11.2018 Synchronization with firmware version 1.15.0 Version 1.7 10.08.2018 Synchronization with firmware version 1.14.0 Version 1.6 8.05.2018 Synchronization with firmware version 1.12.2 Changes: •... - Page 17 +7(383) 274-47-87, +7(383) 272-83-31, E-mail: techsupp@eltex.nsk.ru Visit Eltex official website to get the relevant technical documentation and software, benefit from our knowledge base, send us online request or consult a Service Centre Specialist in our technical forum. Eltex official website: http://eltex-co.ru Technical forum: http://eltex-co.ru/forum...
Need help?
Do you have a question about the WEP-2ac and is the answer not in the manual?
Questions and answers