Perlesmith PSLFK1-24 Manual

LARGE FULL-MOTION TV WALL MOUNT
PSLFK1-24
Thank you for choosing our product! We strive to provide the best quality and
services for our customers. Would you kindly share your experience on Amazon if
you are satisfied? Should you have any issues, please don't hesitate to contact us.
Telephone：800-5566-806 Mon-Fri 10am - 6pm (PST) (USA)
Email：supportus@perlesmith.com (US/CA/DE/UK/FR/IT/ES/JP/AU)
STEP 1 Check the VESA pattern of your TV
Measure the distance between the
holes located at the back of your TV
(these measures may form the shape of
a square, or a rectangle) and check
that these taken measures are within
the VESA(*) range for this wall mount.
(*) VESA: International standard
established by the TV manufacturers
used to determine if LCD / LED TVs
are compatible with wall mounts.
Max 600mm（23 5/8 in）
* WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER
INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
* If you do not understand the instructions or have any concerns or questions, please contact a qualified
installer.
*
Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware
* included must be used. If you require replacement parts, contact customer service at
supportus@perlesmith.com.
This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being
defined as a wall consisting of a minimum of 2" x 4" studs with a maximum of 24" stud spacing with a
V5.0
maximum of 1/2" of wall covering (drywall, lath, plaster).For custom installations please contact a
* qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of
* the total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for
* verifying that the wall structure/surface will safely support the total load.
This product may contain moving parts. Use with caution.
DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
Please check www.perlesmith.com for more products and company information.
!
CAUTION!
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN INSTABILITY
CAUSING POSSIBLE INJURY. USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE
ADJUSTING. NOT SUITABLE FOR A TV THAT SURPASSES THE TELEVISION MAXIMUM WEIGHT CAPACITY
AND RECOMMENDED DIAGONAL MEASURED TV SIZE!
Tools Needed
Tape
Stud Pencil
Finder
measure
STEP 2
Install TV bracket
Check TV screws
Please select the proper screw length for your TV
by hand tightening to check your plat panel
thread depth.
STEP 2A Flat back TV (Universal monitor plate)
Connect TV Brackets to back of TV
75 mm ≈ 2 7/8 in
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
300 mm ≈ 11 3/4 in
400 mm ≈ 15 3/4 in
600 mm ≈ 23 5/8 in
3
WARNING!
WEIGHT CAPACITY
132 lbs
(60kgs)
MAXIMUM WEIGHT CAPACITY
7/32 in. 1/2 in.
Screw
Level Drill
Hammer
(5.5 mm) (12.7 mm)
(included driver
Wood Drill
inside the box)
When attaching brackets to the flat screen,
be careful not to over tighten screws and be
sure that screws do not bottom out in the
mounting holes.
Too Short Too Long
Correct Correct
M-A M-C
M-E
M-H
04
Hardware Included
Arm and
x1
Wall Plate 01
Wall Extension A
Arm Extensions x2
03
x2
05
TV Bracket
04 x2
Wall Extension B
06 x2
TV Screws / Washers
Philips Screws Philips Screws Philips Screws Spacers
M4 x 12mm M6 x 15mm M8 x 15mm L10mm
M4 x 30mm M6 x 30mm M8 x 45mm
x4 x4 x4 x4 x4 x8
x4
M-A M-B M-C M-D M-E M-F M-G
1
STEP 2B
Round back TV (Universal monitor plate)
Connect TV brackets to back of TV
Wall Plate Install
STEP 3
3-1
4
Front Support 02 x1
Hardware
(Wall)
Lag Bolts Washers
Ø8mm
5/16 x 2½ in
x4 x4
A
B
Hardware （product)
Washers Spacers
Allen
Washers
Nuts
Ø6mm L5mm
Wrench
Ø8mm
M4-5-6 M8
x1
x4 x8
x8 x8
C E
M-H M-I D
2
M-B M-D
M-F
M-H
04
M-I
Use a stud finder (not included) to locate
wood studs. Mark the edge and center
locations.
5