Advertisement
Quick Links
TV Wall Mount
Instruction Manual
V1.0
Large Tilting Wall Mount for 42" – 85" TVs up to 75kg
Model: PSLT9
Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to
provide you with the best quality products and services in the industry. Should you have
any issues, please don't hesitate to contact
AV Supply Group as below:
New Zealand | P: 6492749172 |
E: info@avsupply.co.nz
Australia
|
P: 61390714585
|
E: info@avsupplygroup.com.au
Advertisement
Related Manuals for Perlesmith PSLT9
Summary of Contents for Perlesmith PSLT9
- Page 1 Large Tilting Wall Mount for 42” – 85” TVs up to 75kg Model: PSLT9 Thank you for choosing this PERLESMITH product! At PERLESMITH we strive to provide you with the best quality products and services in the industry. Should you have...
- Page 2 IMPORTANT SAFETY INFORMATION Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at info@avsupply.co.nz(NZ) /info@avsupplygroup.com.au(AU). CAUT ION: Avoid potential personal injuries and property damage! •...
- Page 3 Tools Needed (Not lncluded) Stud Finder Tape Measure Pencil Drill Hammer 7/32 in. (5.5 mm) 3/8 in. (10mm) 1/2 in. (13mm) Phillips Screwdriver Level Wood Drill Concrete Drill Socket Wrench Supplied Parts and Hardware Warning:This product contains small items that could be a choking hazard if swallowed.
- Page 4 Bolts （Only one bolt size fits your TV） Note: The bolts are shown in accordance with the actual size [D1] [D2] M6 x 15mm M6 x 35mm [E1] [E2] [E3] M8 x 15mm M8 x 35mm M8 x 50mm Supplied Parts and Hardware for Step 2 Wall Plate Wall Plate Template...
- Page 5 CAUTION! This anchor is for con- Wall crete or brick walls Anchor ONLY. DO NOT use them in drywall or wood studs. Step 1 Secure the TV Brackets to TV Select TV Bolts Only one bolt size fits your TV. Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
- Page 6 Option A (For Flat Back TV) D1/E1 Option B (For Round Back TV) D2/E2/E3 Alternate Spacer Setups C2/C3 Option C (For TV with A “Bump”) Spacers may be necessary for 2 holes ONLY. D1/E1 D2/E2/E3 Alternate Spacer Setups C2/C3...
- Page 7 Option D For cable interference or inset holes, use spacers to create extra space between the TV and TV brackets C2/C3 D2/E2/E3 Alternate Spacer Setups Attach Front Support to Wall Step 2 For wood stud installation, follow STEP 2A For concrete installation, follow STEP 2B Wood Stud Option Step WARNING:...
- Page 8 2A-1 Use a stud finder(not included) to locate wood studs or use an awl (not included) to verify the edges. Mark the edge and center locations. (Not lncluded) 2A-2 Position the wall plate template [02] at your desired height and line up the holes with your stud center line.
- Page 9 2A-4 Install the front support using lag screws [A1] and washers [A2]. Tighten the lag screws [A1] only until the washers [A2] are pulled firmly against the front support. 1/2 in. (13mm) Socket Wrench (Not inclued) Solid Concrete or Concrete Block Option Step 2B WARNING: ●...
- Page 10 2B-1 2B-2 Drill 4 pilot holes using a 3/8 in. (10mm) diameter drill bit. Make Position the wall palte template [02] at sure the depth is not less than 2 your desired height, level the wall plate 3/4 in. (70mm). Never drill into the template and mark the pilot hole mortar between blocks.
- Page 11 Secure Your TV to the Front Support Step 3 HEAVY! You may need assistance with this step. Lock 1. Hang the TV with TV brackets [03] and [04] to the front support. 2. Press the bottom of the TV into the front support until the latches lock the TV in place.
- Page 12 Adjustment 2 Tilt Adjustment Your TV should be adjusted easily when moved, then stay in place. If your TV is too loose or too tight, adjust side tension knob [T] . NOTE: Once your TV is in place, tighten the side tension knob [T] to prevent unwanted movement.