Perlesmith PSLFK1 Installation Instructions

LARGE FULL-MOTION TV WALL MOUNT
for most 37" to 70" TVs
up to 132 lbs
PSLFK1
STEP 1
Check the VESA pattern of your TV
Measure the distance between the holes
located at the back of your TV (these
measures may form the shape of a square, or
a rectangle) and check that these taken
measures are within the VESA(*) range for this
wall mount.
(*) VESA: International standard established
by the TV manufacturers used to determine if
LCD / LED TVs are compatible with wall
mounts.
Max 600mm（23 5/8 in）
* WARNING! SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR
ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
* If you do not understand the instructions or have any concerns or questions, please contact a qualified installer.
V2
* Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you
require replacement parts, contact customer service at customerservice@perlegear.com.
* This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of a
minimum of 2" x 4" studs with a maximum of 16" stud spacing with a maximum of 1/2" of wall covering (drywall, lath, plaster).For custom
installations please contact a qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of the
total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure/sur-
face will safely support the total load.
* This product may contain moving parts. Use with caution.
* DO NOT EXCEED THE MAXIMUM WEIGHT CAPACITY FOR THIS PRODUCT.
*
Please check www.perlesmith.com for more products and company information.
!
CAUTION!
MAXIMUM SCREEN SIZE
USE WITH PRODUCTS LARGER THAN THE MAXIMUM WEIGHT AND SIZE MAY RESULT IN INSTABILITY CAUSING POSSIBLE INJURY.
USER MUST REMOVE TELEVISION OR OBJECT OFF THE BRACKET BEFORE ADJUSTING. NOT SUITABLE FOR A TV THAT
SURPASSES THE TELEVISION MAXIMUM WEIGHT CAPACITY AND RECOMMENDED DIAGONAL MEASURED TV SIZE!
Tools Needed
Tape
Stud Pencil Level
Finder
measure (included
inside the box)
STEP 2
Install TV bracket
Check TV screws
Please select the proper screw length for your TV by hand tightening to check your plat panel thread depth.
75 mm ≈ 2 7/8 in
100 mm ≈ 4 in
200 mm ≈ 7 7/8 in
300 mm ≈ 11 3/4 in
400 mm ≈ 15 3/4 in
600 mm ≈ 23 5/8 in
3
WARNING!
WEIGHT CAPACITY
55
" " " "
70"
60 kg
132 lbs
MAXIMUM WEIGHT CAPACITY
7/32 in. 1/2 in.
Screw
Drill
Hammer
(5.5 mm) (12.7 mm)
driver
Wood Drill 1
Too Short Too Long
Correct Correct
4
Hardware Included
Arm and
x1
Wall Plate 01
Arm Extensions x2
03
TV Bracket
04 x2
TV Screws / Washers
Philips Screws Philips Screws Philips Screws Philips Screws
M4 x 12mm M5 x 12mm M6 x 15mm M8 x 15mm
M4 x 30mm M5 x 30mm M6 x 30mm M8 x 30mm
x4 x4 x4 x4 x4 x4 x4
M-G
STEP 2A
Flat back TV (Universal monitor plate)
Connect TV Brackets to back of TV
STEP 2B
Round back TV (Universal monitor plate)
Connect TV brackets to back of TV
Front Support
02 x1
Hardware
（Wall )
Lag Bolts Washers
Ø8mm
5/16 x 2½ in
x4 x4
A
B
Spacers Washers Spacers
L10mm Ø6mm L5mm
M4-5-6
x4 x4 x4 x8
M-H M-I M-J M-K
2
M-A M-C
M-E M-G
M-J
04
M-D M-B
M-F M-H
M-J
04
M-I
5