Gage Bilt GB703VT Installation Manual
  1. Manuals
  2. Brands
  3. Gage Bilt Manuals
  4. Tools
  5. GB703VT
  6. Installation manual

Gage Bilt GB703VT Installation Manual

Hide thumbs Also See for GB703VT:
Table of Contents

Advertisement

Quick Links

Download this manual
GB703VT
S/N: 3157 AND ABOVE
PLEASE CONTACT GAGE BILT FOR
ALL OTHER SERIAL NUMBERS.
INSTALLATION TOOL
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE
E-MAIL US FOR A DISTRIBUTOR NEAR YOU.
GAGE BILT Inc.
GAGE BILT
44766 Centre Court
(586) 226-1500
Clinton Twp. MI 48038
(586) 226-1505 Fax
MADE IN U.S.A.
e-mail: solutions@gagebilt.com / www.gagebilt.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GB703VT and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Gage Bilt GB703VT

Summary of Contents for Gage Bilt GB703VT

  • Page 1 GB703VT S/N: 3157 AND ABOVE PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS. INSTALLATION TOOL GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU. GAGE BILT Inc. GAGE BILT 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax MADE IN U.S.A.

  • Page 2: Table Of Contents

    Setting stroke - .780" (19.81 mm) Rated pull load - 2,200 lbs. (9.79 kN) Noise level - 81.5 dB (A) Vibration - Tested– No Hazards Found S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 3: Warnings

    Shock: It is recommended operator wear a suitable gloves WARNING during operation where prolonged use is expected. Air pressure not to exceed 100 psi (6.9 bar). S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 4: Principle Of Operation

    Image may not reflect actual tool S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 5: How To Use The Gb703Vt

    Always disconnect air supply when tool is not in use to prevent accidental start-up. NOSE HEAD ASSEMBLY CYLINDER ASSY DEFLECTOR RIVET WORK ACTUATOR SHIPPING ASSY PLUG QUICK DISCONNECT FITTING Image may not reflect actual tool S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 6: Description And Maintenance

    2,200 (9.79 kN) lbs. with 90 psi (6.2 bar) air pressure at the air inlet. The GB703VT riveter operates on a wide range of air pressure, with 90 to 100 psi (6.2-6.9 bar) providing the maximum efficiency. At 90 lbs.

  • Page 7: Filling And Bleeding

    With the actuator lever assy (704343) released, check dimension (A). With the actuator lever assy (704343) depressed, check dimension (B). If stroke is not consistent within 1/64" (.0156) repeat bleeding steps 4-6. .365 (9.3mm) 1.145 (29.1mm) S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 8: Troubleshooting

    Note: The vacuum regulator may visually appear clean, but still may be contaminated with a thin film, therefore, the steps above should be performed to assure best performance. S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 9: Overhaul And Disassembly

    WARNING: Tool must be maintained in a safe working condition at all times and examined on a daily basis for damage or wear. Any repair should be done by qualified personnel trained on Gage Bilt procedures. WARNING: When operating, repairing or overhauling tool, wear approved eye protection. Do not look in front of tool or rear of tool when installing fastener.

  • Page 10: Parts List

    The re-assembly sequence is the opposite of disassembly. (See Filling and Bleeding instructions.) Apply Loctite® #242 and torque the button head cap screws (A-928) uniformly to 40 inch lbs. to prevent leakage around the gasket (704129). S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 11 NOTE: Valve spring installation tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be pulled out using valve sleeve removal tool (704163). S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 12: Dexron® Iii Oil Safety Data

    Use material for its intended purpose or recycle if possible. Oil collection services are available for used oil recycling or disposal. Place contaminated materials in containers and dispose of in a manner consistent with applicable regulations. S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 13: Nose Assembly Selection Chart

    S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.
  • Page 14 S/N: 3157 AND ABOVE 9/14 PLEASE CONTACT GAGE BILT FOR ALL OTHER SERIAL NUMBERS.

  • Page 15: Eu Conformity And Warranty

    GAGE BILT DECLARATION OF CONFORMITY MANUFACTURER: Gage Bilt Inc. 44766 Centre Ct. Clinton Twp. Michigan (586-226-1500) WE DECLARE THAT THE EQUIPMENT SPECIFIED HEREIN CONFORMS TO THE FOLLOWING DIRECTIVES AND STANDARDS Machinery Directive 2006/42/EC EN12100-1 & EN12100-2 EN792-1:2000+A1 EU REPRESENTATIVE Edgar Hausmann GmbH Förster-Busch-Str. 10 D-34346 Hann. Münden Germany EQUIPMENT DESCRIPTION: GB703VT FASTENER INSTALLATION TOOL This product specified above conforms to the above dIrectives and standards.

Table of Contents