Related Manuals for Automatic Technology Axess Pro Series
Summary of Contents for Automatic Technology Axess Pro Series
- Page 1 Axess Pro Series 3000 ® Industrial Roller Shutter Opener Doc # 160027_01 Part # 13383 Released 05/03/14...
- Page 2 Automatic Technology (Australia) Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims all conditions or warranties, statutory or otherwise which may be implied by laws as conditions or warranties of purchase of an Automatic Technology (Australia) Pty Ltd industrial roller shutter opener.
-
Page 3: Table Of Contents
13.1 Selecting The Function To Be Coded 13.2 Activate Remote Code Set Mode 14. Setting Pedestrian Position 14.1 Setting Pedestrian Position 14.2 Checking Pedestrian Position 14.3 Error Displays 13.3 Removing the Battery From the Transmitter Owner Installation Instructions Axess Pro Series 3000... -
Page 4: Important Safety Instructions
If the power supply cord is damaged, it must be replaced by an • Automatic Technology service agent or suitably qualified person. • Electrical wiring must be compliance with the local building an electrical codes. - Page 5 Security • Make sure the shutter is fully closed before leaving the driveway. . Entanglement in • Keep hands and loose clothing clear of shutter and opener at all times. moving door Owner Installation Instructions Axess Pro Series 3000...
-
Page 6: Controller Input And Outputs
Serial interface connector Position sensor connector Position sensor connector 10 Amps slow blow mains fuse FLQ10 - 500Vac time delayed fuse x 3 TDC11- 250mA 1000Vac slow blow fuse 3-phase 415Vac mains input terminal Axess Pro Series 3000 Owner Installation Instructions... -
Page 7: Operating Controls
First Safety Beam Input Common For Safety Beams Common Terminal For Control Inputs FIRE N/O , N/C Input Terminal N/O Input Terminal N/O , N/C Input Terminal N/O , N/C Input Terminal N/O Input Terminal Owner Installation Instructions Axess Pro Series 3000... -
Page 8: Set Up Requirements
Set ups are as follows; Set Up Items Required Dead Man Set Up Drive Unit, Manual Console Automated Full Logic Set Up with Drive Unit, Logic Console, transmitter Safety Beams and safety beams. Axess Pro Series 3000 Owner Installation Instructions... -
Page 9: Pre-Installation Requirements
Owner Installation Instructions Axess Pro Series 3000... -
Page 10: Installation
Failure to comply will void the warranty and may cause serious personal injury and/or property damage. WARNING! Ensure that network cable is affixed properly and away from the moving parts of the shutter and opener. Axess Pro Series 3000 Owner Installation Instructions... -
Page 11: Programming The Opener
ATTENTION! No Safety Beams have been detected. “Safety Close’ mode has been turned on. See Manual for details. Press SET to continue. NOTE: Fitting Safety Beams enables the Auto-Close feature to become active. Owner Installation Instructions Axess Pro Series 3000... -
Page 12: Safety Beam Installation
Repeat steps a and b to assemble the Safety Beam receiver. CAUTION: Locate the Safety Beam in a strategic location in the doorway. Automatic Technology recommend that the sensor is placed 100mm above the floor level and as close as possible to the door opening. -
Page 13: Wiring The Safety Beam To V2 Logic Console
Make horizontal and/or vertical adjustment on the transmitter and/ or receiver until the red LED on the receiver turns on, indicating alignment. Approaching to the alignment is indicated by fast flashes on the red receiver LED. Owner Installation Instructions Axess Pro Series 3000... -
Page 14: Setting Limits Via Console
After this, If PE Beams are installed, the opener can be operated with the OPEN or CLOSE button on the logic console or from the transmitter. Otherwise, the controller will be loaded with “Safety Close Mode”. (Section 16.1) Axess Pro Series 3000 Owner Installation Instructions... -
Page 15: Setting Limits Via Transmitter
(2) times (depending on the position of the shutter and the power up condition). A single beep will be heard once the process is complete. Owner Installation Instructions Axess Pro Series 3000... -
Page 16: Coding Transmitter
(e.g. Button 1 has been coded with the OSC function assigned). b. If the button’s function activates the shutter (PED, SWP, OSC, CLS, STP or OPN) wait for the shutter to complete its cycle. Axess Pro Series 3000 Owner Installation Instructions... -
Page 17: Activate Remote Code Set Mode
Ped position, then the door will close. 14.3 Error Displays During the above procedure many error checks are performed. If an error is detected, a message will be displayed indicating the error. Owner Installation Instructions Axess Pro Series 3000... -
Page 18: Auto-Close Mode For V1 Console
This mode enables Auto-Close feature after power up. to close the shutter. Details about the four Auto-Close modes follow. Automatic Technology strongly recommend using a Safety Beam for added safety. Menu 3.1 Standard Auto Close This mode is selected by entering a non-zero time for the STD Auto-Close parameter. -
Page 19: Auto-Close Mode For V2 Console
Details about the four Auto-Close modes follow. Automatic Technology strongly recommend using a Safety 16.5 Auto-Close After Obstruction: Beam for added safety. Three parameters are provided to enable the Auto-Close feature to be activated after obstructions and power up. -
Page 20: Time Clock
This feature will let the user activate the stop function until the next program starts. The door will not open or close while stop is activated. Release the controls from the timer. Free Door This will temporarily disable the program. Axess Pro Series 3000 Owner Installation Instructions... -
Page 21: Day Light Saving Time Adjustment
Press OPEN to increase or CLOSE to decrease the time. e. Press SET to save the new time. f. Press the STOP button two times to exit. g. Test the light operation. Owner Installation Instructions Axess Pro Series 3000... -
Page 22: Specifications
If the Safety Beams are not installed then the controller will automatically go into “Safety Close“ mode. A limited number of features are available in this mode, please refer to menu 6.1 in Section 16.1. Axess Pro Series 3000 Owner Installation Instructions... -
Page 23: Troubleshooting
Safety Beam not aligned correctly. Re-align optics. SafetyBeam is obstructed. Remove obstruction from path of Safety Beam Shutter obstructed when closing or Remove obstruction. opening. Auto-Close time not set. Set Auto-Close times. (Section 15 & 16) Owner Installation Instructions Axess Pro Series 3000... -
Page 24: Maintenance
21.5 Service Indicator 21.2 Lubrication (every 3 - 6 months) As a reminder the Axess Pro Series 3000 has a built in To ensure a long and trouble free life for your shutter the maintenance counter. This counter has a factory default of following is recommended: 60,000 cycles, and it is adjustable from 0 to 60,000 cycles. -
Page 25: Appendix
AUTO-CLOSE AFTER CLOSE OBSTRUCTION 16.5 Enables Auto-Close feature after close obstructions (requires Safety Beams) AUTO-CLOSE AFTER OPEN OBSTRUCTION 16.5 Enables Auto-Close feature after open obstructions Owner Installation Instructions Axess Pro Series 3000 AUTO-CLOSE AFTER POWER UP 16.5 Enables Auto-Close feature power up... - Page 26 Selects ID for controller, sent with activity report VACATION MODE 6.16 Appendix C Selects Vacation Mode - disables remote control PASSWORD 6.17 Appendix C Selects password protection for all changes Transmitter Grouping 6.18 Appendix C Axess Pro Series 3000 Owner Installation Instructions...
- Page 27 Menu 9 - Memory Tools CLR CONTROL Appendix E CLR TRANSMITTERS (TX’ERS) Appendix E Menu 10 - Setup Travel SETUP LIMITS 10.1 11.1 or 12.4 REPROFILE TRAVEL 10.2 12.5 SET PEDESTRIAN 10.3 15.1 Owner Installation Instructions Axess Pro Series 3000...
-
Page 28: B - Viewing & Editing Logic Console Parameters
Press STOP again to return to the MAIN SCREEN. Saves new Displays “Load value Default?” screen, giving option of loading default value Exits back to View Mode Decrease value Axess Pro Series 3000 Owner Installation Instructions... -
Page 29: C - Control Board Adjustments
The time selected is the amount of time added to STD time when DST is selected. The Options are OFF, 30, 60, 90 or 120 minutes. The GPI input needs to be constantly active to show day light saving time. Owner Installation Instructions Axess Pro Series 3000... - Page 30 This parameter enables activity report outputs. Contact Automatic Technology for more details. 6.15 Activity Report ID This parameter sets the ID of the controller that is sent with the activity report. Contact Automatic Technology for more details. 6.16 Vacation Mode Vacation Mode blocks all but one designated remote control transmitter from activating the Axess Pro Series 3100.
-
Page 31: D - Diagnostic Tools
STOP to exit. Fig D.5 Menu 8.4 Memory Usage This tool displays the number of transmitter store locations used (Fig. D.6). and the number free Used = Free = Fig D.6 Owner Installation Instructions Axess Pro Series 3000... -
Page 32: E - Memory Tools
This option will clear the shutter control memory and reload the factory set defaults for parameters such as the lock time, light time, Auto-Close times etc. It will also clear the travel limits. Menu 9.2 Clear Transmitters (Tx’ers) This option will clear the transmitter storage memory. Axess Pro Series 3000 Owner Installation Instructions... -
Page 33: F - Transmitter Editing
NOTE: If all button functions are set to OFF, when SET is pressed, the opener will prompt to confirm if the transmitter is to be deleted. Press SET to delete or STOP to continue editing. Owner Installation Instructions Axess Pro Series 3000... - Page 34 The second line of the display shows a list of available characters (Fig. F.8). with the current value indicated at the cursor position PRESS 14 I B B SMITH 56789 AB CDEFGHIJ Fig F.8 PRESS Axess Pro Series 3000 Owner Installation Instructions...
-
Page 35: G - Transmitter Management
2 & 3 of the BASIC CODE TRANSMITTER PROCEDURE for each transmitter to be coded. Coding is terminated by pressing the STOP button. Exiting The List To exit the transmitter list, simply press STOP to return to the Code menu. Owner Installation Instructions Axess Pro Series 3000... -
Page 36: Warranty And Exclusion Of Liability
Warranty and Exclusion of Liability b. accidental damage; 1. This Warranty is given by Automatic Technology (Australia) Pty Ltd (ABN c. incorrect installation of the Product; 11 007 125 368) (ATA). 6-8 Fiveways Boulevard, Keysborough 3173, 1300 d. blown fuses, electrical surges, power surges or power spikes;...
Need help?
Do you have a question about the Axess Pro Series and is the answer not in the manual?
Questions and answers