Installing Your New Unit; Basic Connections - JVC DR-MH30B Instructions Manual

Filename [DR-MH30EU_04Name.fm]
DR-MH30EU_00.book Page 19 Thursday, June 3, 2004 11:00 AM

Basic Connections

TV aerial cable
ANTENNA IN
COMPONENT VIDEO OUT
S-VIDEO OUT
ANTENNA
L-1 IN/OUT
OUT
Component
video cable
(not provided)
RF cable 21-pin SCART
(provided) cable
(provided)
It's essential that your unit be properly connected.
ATTENTION:
Your TV must have a 21-pin AV input connector (SCART) for the
basic connection to the unit.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1
Place the unit on a stable, horizontal surface.
2
Connect the unit to a TV depending on the TV and cables you
use.
Page 19
Mains outlet
Mains power cord
Back of unit
AUDIO OUT
Audio cable S-Video
(not provided) cable
(not
provided)
TV

INSTALLING YOUR NEW UNIT

8 Basic Connection
To connect to a TV with 21-pin SCART input connector —
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the ANTENNA IN connector on
the rear panel of the unit.
C Connect the ANTENNA OUT connector on the rear panel of the
unit and the TV's aerial connector with the provided RF cable.
D Connect the L-1 IN/OUT connector on the rear panel of the unit
and the TV's 21-pin SCART connector with a provided 21-pin
SCART cable.
The L-1 IN/OUT connector accepts and delivers either a composite
signal (regular video signal), Y/C signal or RGB signal.
Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to
the type of your TV's SCART connector.
8 S-Video Connection
To connect to TV's S-VIDEO input and AUDIO input
connectors —
A Perform A – C in "Basic Connection".
B Connect the unit's S-VIDEO OUT connector to the TV's
S-VIDEO input connector.
C Connect the unit's AUDIO OUT connectors to the TV's AUDIO
input connectors.
You can obtain high-quality S-VHS pictures.
With S-VIDEO connection, you cannot use the Preset Download
function. ( pg. 21)
If your TV is not stereo-capable, use the unit's AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
8 Component Video Connection
To connect to TV's component video input connectors —
A Perform A – C in "Basic Connection".
B Connect the unit's COMPONENT VIDEO OUT connectors to
the TV's component video input connectors.
C Connect the unit's AUDIO OUT connectors to the TV's AUDIO
input connectors.
You can obtain high-quality component video pictures.
If your TV is not stereo-capable, use the unit's AUDIO OUT
connectors to connect to an audio amplifier for Hi-Fi stereo sound
reproduction.
By using the component video connection, you can view the images
in the progressive mode. For switching to the progressive mode, refer
to "Scan Mode Set" ( pg. 71).
NOTE:
Select an appropriate option of "L-1 OUTPUT" as follows (
When your TV's SCART
connector accepts:
Composite signals
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
RGB signal
Component video signal
3
Plug the end of the mains power cord into a mains outlet.
"LOADING" blinks on the front display panel when the AC plug of the
mains power cord is connected into a mains outlet and it takes
approximately 50 seconds for the unit to be turned on. This is not a
malfunction.
Masterpage:Right0
19
EN
pg. 63):
Set "L-1 OUTPUT" to:
"SCART VIDEO"
"SCART S-VIDEO"
"SCART RGB"
"COMPONENT"
Thursday, 3 June 2004 10:46