Table of Contents
Advertisement
INSTALLING YOUR NEW UNIT
16
EN
Basic Connections
TV aerial cable
To [ANTENNA IN]
To [L-1 IN/OUT]
To
To [COMPONENT
[ANTENNA
VIDEO OUT (Y/P
OUT]
P
)]
R
21-pin SCART
RF cable
(supplied)
(supplied)
Component
video cable
(not supplied)
To 75 ohm terminal
It's essential that your unit be properly connected.
ATTENTION:
●
Your TV must have a 21-pin AV input connector (SCART) for
the basic connection to the unit.
●
Connect the AC plug only after all connections to the TV has
been completed.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1
Make sure the package contains all of the accessories listed in
ASPECIFICATIONSB (A pg. 84).
2
Place the unit on a stable, horizontal surface.
3
Connect the unit to a TV depending on the TV and cables you
use.
Mains outlet
Mains power cord
Back of unit
To [AUDIO
To [S-VIDEO
OUT]
OUT]
/
B
Audio cable
(not supplied)
S-Video
cable
(not supplied)
cable
TV
8 Basic Connection
To connect to a TV with 21-pin SCART input connector ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV aerial cable to the [ANTENNA IN] connector on
the rear panel of the unit.
C Connect the [ANTENNA OUT] connector on the rear panel of
the unit and the TV's aerial connector with the supplied RF
cable.
D Connect the [L-1 IN/OUT] connector on the rear panel of the
unit and the TV's 21-pin SCART connector with a supplied 21-
pin SCART cable.
●
The [L-1 IN/OUT] connector accepts and delivers either a
composite signal (regular video signal), Y/C signal or RGB
signal.
●
Set your TV to the VIDEO (or AV), Y/C, or RGB mode
according to the type of your TV's SCART connector.
8 S-Video Connection
To connect to TV's S-VIDEO input and AUDIO input
connectors ^
A Perform A – C in ABasic ConnectionB.
B Connect the unit's [S-VIDEO OUT] connector to the TV's
S-VIDEO input connector.
C Connect the unit's [AUDIO OUT] connectors to the TV's AUDIO
input connectors.
●
You can obtain high quality S-VHS pictures.
●
If your TV is not stereo capable, use the unit's [AUDIO OUT]
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
8 Component Video Connection
To connect to TV's component video input connectors ^
A Perform A – C in ABasic ConnectionB.
B Connect the unit's [COMPONENT VIDEO OUT (Y/P
connectors to the TV's component video input connectors.
C Connect the unit's [AUDIO OUT] connectors to the TV's AUDIO
input connectors.
●
You can obtain high-quality component video pictures.
●
If your TV is not stereo-capable, use the unit's [AUDIO OUT]
connectors to connect to an audio amplifier for Hi-Fi stereo
sound reproduction.
●
By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to AScan Mode SetB (A pg. 72).
NOTE:
Select an appropriate option of AL-1 OUTPUTB as follows
(A pg. 64):
When your TV's SCART
connector accepts:
Composite signals
Y/C signal (separated
luminance (brightness) and
chrominance (colour) signals)
RGB signal
Component video signal
When the setting selected is not in accordance with the TV
connected and depending on the type of appliance connected to
the unit, the correct picture will not appear.
4
Plug the end of the mains power cord into a mains outlet.
●
ALOADINGB blinks on the front display panel when the AC plug
of the mains power cord is connected into a mains outlet and it
takes approximately 50 seconds for the unit to be turned on.
This is not a malfunction.
/P
)]
B
R
Set AL-1 OUTPUTB to:
ASCART VIDEOB
ASCART S-VIDEOB
ASCART RGBB
ACOMPONENTB
Advertisement
Table of Contents
