Automatic Satellite Programme Recording - JVC DR-MH30B Instructions Manual

Filename [DR-MH30EU_07Timer Recording.fm]
DR-MH30EU_00.book Page 50 Thursday, June 3, 2004 11:00 AM
TIMER RECORDING
50
EN
Automatic Satellite Programme
Recording
This function allows you to automatically record a satellite
programme which is timer-programmed on your external satellite
receiver. Connect a satellite receiver to the unit's L-2 IN/
DECODER connector and programme the timer on the satellite
receiver. The unit starts or stops recording by the signals input
from the satellite receiver. After recording, the unit's power shuts
off automatically.
ATTENTION:
When you record programmes by connecting to a digital terrestrial
receiver (Freeview receiver or similar), perform the same steps as

"Automatic Satellite Programme Recording" (

possible to operate the digital terrestrial receiver (Freeview
receiver or similar) by using the provided satellite controller.
Be sure not to turn on the satellite receiver before the programme
is executed; otherwise, the unit will start recording when the
satellite receiver's power is turned on.
If you have connected another appliance other than a satellite
receiver to the L-2 IN/DECODER connector, be sure not to engage
the Automatic Satellite Programme Recording mode; otherwise,
the unit will start recording when the connected appliance's power
is turned on.
Automatic Satellite Programme Recording and timer-recording
cannot be done at the same time.
HDD
REC MODE
SAT#
Page 50
Make sure the satellite receiver is connected to the unit's L-2 IN/
DECODER connector.
Programme the timer on the satellite receiver.
Slide the TV/CABLE/SAT/DVD switch to DVD.
1
Press HDD or DVD to choose the recording deck.
2
Set "L-2 SELECT" to "SAT VIDEO" or "SAT S-VIDEO".
(
Also refer to "IMPORTANT" on page 67.
3
Press REC MODE repeatedly to set the recording mode.
4
Press and hold SAT# for about 2 seconds to engage the
Automatic Satellite Programme Recording mode. "SAT#" appears
on the front display panel.
NOTES:
To disengage the Automatic Satellite Programme Recording mode,
pg. 50). It is not
press SAT#.
If the unit's power is off, it is not possible to engage the Automatic
Satellite Programme Recording mode.
In step 4, if "SAT#" blinks quickly on the front display panel even
though your satellite receiver's power is off, Automatic Satellite
Programme Recording will not work properly with that satellite
receiver*. If this is the case, perform "Manual Timer Programming"
(
* Some satellite receivers output signals even if the power is off.
"SAT#" blinks on the front display panel while Automatic Satellite
Programme Recording is in progress.
For timer programming of the satellite receiver, refer to the instruction
HDD DVD
manual of the satellite receiver.
Automatic Satellite Programme Recording is not possible if your
satellite receiver does not have a timer.
Pressing the unit's 1 button while Automatic Satellite Programme
Recording is in progress turns off the unit's power and disengages
the Automatic Satellite Programme Recording mode.
If there are more than one satellite programmes you wish to record
with Automatic Satellite Programme Recording, it is not possible to
set different recording modes for each programme.
Depending on the type of satellite receiver, the unit may not record a
CABLE/DBS
TV DVD slight portion of the beginning of the programme or may record
slightly longer than the actual length of the programme.
If you engage the Automatic Satellite Programme Recording mode
DVD
when the satellite receiver's power is on, the unit will not start
Automatic Satellite Programme Recording even though "SAT#"
blinks on the front display panel. When the satellite receiver shuts off
once and is turned back on again, the unit starts recording.
You can also record a programme from your cable system in the
same way if the system has a timer.
Just Clock (
Programme Recording mode is engaged.
pg. 63)
pg. 48) to timer-record a satellite programme.
Automatic Satellite Programme Recording is not possible with those
satellite receivers.
pg. 75) does not work when the Automatic Satellite
Masterpage:Left+
Thursday, 3 June 2004 10:46