Video Plus+ System Setup; Tuner Set - JVC DR-MH30B Instructions Manual

Filename [DR-MH30EU_10Subsidiary.fm]
DR-MH30EU_00.book Page 72 Thursday, June 3, 2004 11:00 AM
SUBSIDIARY SETTINGS
72
EN
VIDEO Plus+ System Setup
®
IMPORTANT:
Normally, Auto Set Up ( pg. 20), Preset Download (
Auto Channel Set ( pg. 72) sets the Guide Program numbers
automatically. You need to set the Guide Program numbers manually
only in the following cases.
When timer-programming with the VIDEO Plus+ system, the
channel position, where the station you wish to record is received
on your unit, is not selected,
OR
when you add a channel after Auto Set Up, Preset Download or Auto
Channel Set has taken place,
—Set the Guide Program number for that station manually.
When you wish to timer-record a satellite programme with the
VIDEO Plus+ system,
—Set the Guide Program numbers for all satellite broadcasts received
on your satellite receiver.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
Guide Program Number Set
1
Press SET UP to access the Main Menu screen.
2
Press w e to select "INITIAL SET UP", then press ENTER.
3
Press w e to select "TUNER
SET", then press ENTER.
4
Press rt w e to select "GUIDE
PROG SET", then press ENTER.
5
Press rt to select "GUIDE
PROG", then press ENTER.
6
Press rt to select the Guide
Program number for the desired
station as shown in the TV listings.
Then press ENTER.
To change the Guide Program
number in 10 increments, press and
hold rt.
7
Press rt to select "TV PROG", then press ENTER. Press rt
to select the number of the unit's channel position on which the
Guide Program number's broadcast is received by the unit or the
satellite receiver. Then press ENTER.
Pressing AUX changes "TV PROG" to "SAT".
To timer-record a satellite programme with the VIDEO Plus+ system,
you need to install the provided Satellite Controller and perform the
procedure described in "Satellite Receiver Control Setting"
( pg. 25).
Repeat steps 5 – 7 as necessary.
8
Press SET UP to complete the setting.
Guide Program Number
"Guide Program (GUIDE PROG) number" refers to the assigned
TV station numbers, according to broadcast area, for the VIDEO
Plus+ timer recording. The Guide Program Numbers can be
found in most TV listings.
Page 72
pg. 21) or
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP

TUNER SET

CLOCK SET
AUTO CH SET MANUAL CH SET
SAT CONTROL SET GUIDE PROG SET
11
12
13
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT SELECT
11
12 INITIAL SET UP > GUIDE PROG SET
13
GUIDE PROG 1
TV PROG YLE2 1
RETURN
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT SELECT
Masterpage:Left+
Tuner Set
Your unit needs to memorise all necessary stations in channel
positions in order to record TV programmes. Auto Channel Set
automatically assigns all receivable stations in your area to call
them up by using the PR +/– buttons without going through any
vacant channels.
Turn on the unit.
Turn on the TV and select the AV mode.
Slide the TV/CABLE/SAT/DVD switch to DVD.
ENTER
IMPORTANT:
Perform the following steps only if —
— Auto Channel Set has not been set correctly by Auto Set Up
or by Preset Download. ( pg. 20, 21)
— you have moved to a different area or if a new station starts
broadcasting in your area.
Auto Channel Set
1
Press SET UP to access the Main Menu screen.
2
Press w e to select "INITIAL SET UP", then press ENTER.
3
Press w e to select "TUNER SET", then press ENTER.
4
Press rt w e to select
"AUTO CH SET", then press
ENTER.
When you have connected the unit
to a TV offering T-V Link via a
fully-wired 21-pin SCART cable
( pg. 19), the unit automatically
performs the Preset Download
and the T-V LINK screen will
appear. ( pg. 21)
The Auto Set screen appears, and
remains on screen while the unit
searches for receivable stations.
CABLE/DBS
TV DVD
rtwe
SET UP
DVD VIDEO SET UP HDD/DVD SET UP FUNCTION SET UP INITIAL SET UP
TUNER SET CLOCK SET
AUTO CH SET MANUAL CH SET
SAT CONTROL SET GUIDE PROG SET
11
12
13
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT SELECT
INITIAL SET UP > AUTO SET
AUTO SET
PLEASE WAIT...
SET UP ENTER
SELECT WITH [ ] THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
EXIT
SELECT
Thursday, 3 June 2004 10:46