Programming The Relay Module - ADEMCO VISTA-100 Installation Instructions Manual

Programming the Relay Module

– 56 –
www.PDF-Zoo.com
4204 RELAY MODULE
SWITCH
POSITION
OFF ON
0 1
2
ON —
3
ON ON
4
ON ON
5
ON ON
4204
DIP SWITCH
FOR SETTING DEVICE ADDRESS
AND ENABLING/DISABLING TAMPER
COVER TAMPER (REED) SWITCH
4-PIN CONSOLE PLUG
EITHER OR BOTH
CAN BE USED
TB1
13 14 15
Figure 12a: 4204 Relay Module
4204 RELAY MODULE
4204CF RELAY MODULE
SWITCH
POSITION
OFF ON
0 1
2
ON —
3 ON ON
4 ON ON
5
ON ON
DIP SWITCH
FOR SETTING DEVICE
ADDRESS AND
ENABLING/DISABLING
TAMPER
COVER TAMPER (REED) SWITCH
4-PIN CONSOLE PLUG
EITHER OR BOTH
CAN BE USED
TB1
13 14 15 16
YEL
DATA IN
FROM CONTROL
BLK
(–) GROUND
GRN
DATA OUT
TO CONTROL
RED
(+) 12VDC; SUPPLIES POWER TO MODULE
CIRCUITRY (INCLUDING NOTIFICATION
APPLIANCE RELAY COILS). CURRENT DRAIN AT
12V IS: 25 mA + (80mA PER ACTIVE OUTPUT)
Figure 12b: 4204CF Relay Module
1. With at least one alpha keypad (6139/6139R) wired and set to a proper
address, temporarily apply power to the control.
2. Enter data field programming mode: (Installer Code + 8 0 0 0) .
3. From data field programming mode, press #93 to display the "ZONE
PROG?" prompt.
firealarmresources.com
4 2 0 4 A D D R E S S S E T T I N G S
("—" means "OFF")
2 3 4 5 6 7 8 9 10
ON — ON — ON — ON — ON
— — ON ON — — ON ON —
ON ON — — — — ON ON ON
ON ON ON ON ON ON — — —
RELAY C
4
NC
TYPICAL
NO
(SHOWN "OFF")
C
RELAY
3
NC
NO
C
RELAY
2
NC
NO
C
RELAY
1
NC
16 NO
YEL
DATA IN TB2
FROM CONTROL
BLK
(–) GROUND
GRN DATA OUT
TO CONTROL
RED
(+) 12V
4 2 0 4 C F A D D R E S S S E T T I N G S
("—" means "OFF")
2 3 4 5 6 7 8 9
ON — ON — ON — ON —
— — ON ON — — ON ON
ON ON — — — — ON ON
ON ON ON ON ON ON — —
–
NC
NOTIFICATION
APPLIANCE B
NC 2K EOLR
+ #610-7
POLARIZED
NC
NOTIFICATION
APPLIANCES
NC
–
NOTIFICATION
APPLIANCE A
2K EOLR
+
#610-7
NC
+
} POWER FOR POWER FOR
NC
NOTIFICATION APPLIANCE A,
– NOTIFICATION APPLIANCE A,
NOTIFICATION APPLIANCE B
NOTIFICATION APPLIANCE B,
8-28 VDC OR VFW. UP TO 2.4A
TB2
DEPENDING ON BELL CURRENT
8–30VDC OR VFW. UP TO 2.4A DEPENDING
ON BELL CURRENT.
NOTIFICATION APPLIANCE AND
CONSOLE DATA OUTPUTS ARE
POWER LIMITED
11 12 13 14 15
— ON — ON —
— ON ON — —
ON — — — —
— — — — —
10 11 12 13 14 15
ON — ON — ON —
— — ON ON — —
ON ON — — — —
— — — — — —
- ALARM POLARITY
SHOWN
- EACH OUTPUT
PROVIDES
STYLE Y
SUPERVISION
- EACH OUTPUT
RATED 1.2A MAX
- USE
NOTIFICATION
APPLIANCES
COMPATIBLE
WITH
NOTIFICATION
APPLIANCE
POWER SUPPLY
VOLTAGE
RATING