1. Manuals
  2. Brands
  3. ADEMCO Manuals
  4. Security System
  5. Vista-10P
  6. Installation and setup manual

ADEMCO Vista-10P Installation And Setup Manual

Hide thumbs Also See for Vista-10P:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Programming Manual, Installation and Setup Manual
Principal changes from previous version
are indicated by margin lines.
K0735V1 9/02
,QVWDOODWLRQDQG6HW8S*XLGH
AR ME
D
RE AD Y
OFF
ON
9,67$3
6HFXULW\6\VWHP
®




Advertisement

Table of Contents
loading

Related Manuals for ADEMCO Vista-10P

Summary of Contents for ADEMCO Vista-10P

  • Page 1 9,67$3 6HFXULW\6\VWHP ,QVWDOODWLRQDQG6HW8S*XLGH AR ME RE AD Y Principal changes from previous version are indicated by margin lines. ® K0735V1 9/02...

  • Page 2: Recommendations For Proper Protection

    RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations for the Location of Fire and Burglary Detection Devices Help Provide Proper Coverage for the Protected Premises. Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.

  • Page 3: Table Of Contents

    Table Of Contents • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Features and Installation Highlights ....................1-1 Capabilities .............................1-1 Functions..............................1-1 Compatible Devices ..........................1-1...
  • Page 4 Adding Custom Words........................5-12 Programming Installer and User Schedules..................5-14 System Communication and Operation...................6-1 System Communication Overview......................6-1 Report Code Formats...........................6-1 Ademco Contact ID ® ...........................6-3 User Security Codes ..........................6-4 Keypad Functions ..........................6-4 Various System Trouble Displays.......................6-6 Testing the System..........................7-1 About Test Procedures ........................7-1 System Test............................7-1...

  • Page 5: Features And Installation Highlights

    • Up to 4 output relays (4204) plus two on-board triggers (does not support Powerline Carrier Devices) -- Up to 12 output functions. • Ademco 4285/4286 Phone Module; provides access to the system via on premises or off-premises phones for arming, disarming, etc., plus control of relay outputs.

  • Page 6: Important Installation Highlights (Installer Please Read)

    Installation and Setup Guide NOTE: All devices and accessories used in a Canadian installation must be Listed for use in Canada. Important Installation Highlights (Installer Please Read) • This system uses addressable keypads and Relay Modules (see table of addresses in Programming Overview section).

  • Page 7: Mounting And Wiring The Control

    S E C T I O N Mounting and Wiring the Control • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Cabinet and Lock 1.

  • Page 8: Mounting Board With Rf Receiver

    Installation Instructions Mounting Board with RF Receiver 1. a. Remove the receiver board from its case, then insert the top of the board into the slots at the top of the cabinet, as shown in Detail A in Figure 3. Make sure that the board rests on the correct row of tabs.

  • Page 9: Wiring To Keypads

    Mounting and Wiring the Control Wiring to Keypads 1. Connect keypads to the keypad terminals as shown on the Summary of Connections diagram. Determine wire gauge using the Wiring Run Chart below. 2. Set keypad addresses. Refer to the address setting instructions included with the keypads and set each keypad device address according to the chart at right.

  • Page 10: Sounder (Bell) Connections

    Installation Instructions Sounder (Bell) Connections TERMINALS ON EXTERNAL ALARM 1. Make sounder connections to alarm output CONTROL BOARD SOUNDER terminals 3 (+) and 4 (–). For supervised output, continue with steps 2 and 3. 2000 2. Cut the red Bell Supervision Jumper located ALARM OBSERVE OUTPUT...

  • Page 11: Earth Ground

    NP4-12 (two) ‡ 500mA 17.2AH NPG18-12 ‡ NOTE: Use two batteries, connected in parallel. Obtain an Ademco Battery Harness Kit SA5140-1. (Both batteries will fit inside the panel’s cabinet.) Earth Ground Metal Cold Water Pipe: Use a non-corrosive metal strap (copper is recommended) firmly secured to the pipe to which the ground lead is electrically connected and secured.

  • Page 12: Hardwire Zones

    Installation Instructions Hardwire Zones Normally Open Zones/ Normally Open EOLR Zones 1. Connect open circuit devices in parallel across the loop; for EOLR zones, connect the EOLR across the loop wires at the last device. 2. Enable normally open/EOLR zones using Zone Programming mode, “Hardwire Type” prompt. Normally Closed Zones/Normally Closed EOLR Zones 1.

  • Page 13: Installing The Rf Receiver

    Mounting and Wiring the Control Installing the RF Receiver You can any ADEMCO 5800 Series Wireless Receivers, including: RF Receiver No. of Zones 5881L/5882L up to 8 5881M/5882M up to 16 (transmitter zone numbers = 9-24; button zone numbers = 49-56) up to 16 (transmitter zone numbers = 9-24;...

  • Page 14: Installing The Transmitters

    DIP switches (5827) or follow the instructions provided with the device. ULC NOTE: In accordance with ULC standards, the RF supervision period for the VISTA-10P is three hours for Fire zones (Zone Type 9 and 16) and 12 hours for all other zone types.

  • Page 15: Connecting Relay Modules

    • a fire alarm installation, the keyswitch must be BLACK located next to an alphanumeric display keypad. TAMPER SWITCH (N. C.) The Ademco 4146 keyswitch is UL Listed. BROWN BROWN TYPICAL ZONE ON CONTROL LOCK BOARD SWITCH (N. O.)

  • Page 16: On-Board Triggers

    Installation Instructions On-Board Triggers 8-PIN TRIGGER CONNECTOR Connect field wiring to the desired trigger pin on the 8-pin trigger connector centrally located above the terminal strip. You can use a standard keypad cable as shown. If on-board triggers are used, the wiring between the control unit and the UL Listed device must be run STANDARD in conduit, be no more than 3 feet apart and have no...

  • Page 17: Long Range Radio Connections

    Mounting and Wiring the Control The 4285 and 4286 modules are UL Listed only for use on residential fire and UL residential burglar alarm installations. Phone Module Problems If no touch tones are produced following access to the security system from on-premises (this problem may arise in rare cases), it may be necessary to reverse the wires connected to terminals 3 and 4 on the phone module and the wires connected to terminals (21) &...

  • Page 18: Aav Connections

    Phone Module is used, the other shows connections when the 4285/4286 is not used. Connections use one of the on-board triggers. UL installations using the AAV feature must use the ADEMCO UVCM module (part of the ADEMCO UVS system) Suggested AAV Module: ADEMCO UVS (shown) or Eagle 1250 NOTES •...

  • Page 19: Programming Overview

    S E C T I O N Programming Overview • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • About Programming You can program the system at any time, even at the installer's premises prior to the actual installation.

  • Page 20: Wireless Receiver, Transmitters, And Wireless Keys (Keyfobs)

    Installation Instructions Wireless Receiver, Transmitters, and Wireless Keys (keyfobs) Receiver: Set the receiver’s address to “00” using its DIP switches, then set the following options: † RF Jam Option RF House ID Code (if using wireless keypads) † Transmitter Low Battery Report Code †...

  • Page 21: Zone Type Definitions

    Zone Type Definitions You must assign a zone type to each zone, which defines the way in which the system responds to faults in that zone. Zone types are defined below. Zone Type Description Type 00 Program a zone with this zone type if the zone is not used. Zone Not Used •...
  • Page 22 Installation Instructions • Works as a dynamic monitor of a zone fault/trouble (not alarm). In the case of a Type 12 short/open, the message, "*ALARM*-24 Hr. Non-Burg. -#XXX " (where XXX is Monitor Zone the zone number) will be sent to the Central Station. The system keypad will display a “check”...

  • Page 23: Mechanics Of Programming

    Mechanics of Programming Data Field Programming Procedures ( You must use a 2-line Alpha display keypad) Task Procedure A) Press both [ ∗ ] and [#] at the same time within 50 seconds after power is applied Entering Program Mode to the control, OR B) After power-up, enter [Installer code (4-1-1-2)] + 8 0 0.

  • Page 24: Installation Instructions

    Installation Instructions Table of Device Addresses †† This Device Uses Address Reports as Enabled By… RF Receiver *56 zone programming: input device type entry Long Range Radio automatic if output to long range radio field *29 enabled 4286 Voice Module automatic if phone module access code field *28 enabled 4204 Relay Module *79 output device programming: entered at device address prompt:...

  • Page 25: Data Field Programming

    S E C T I O N Data Field Programming • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • About Data Field Programming The following pages provide explanations of this control’s data fields and is intended to be used in conjunction with the Programming Guide.

  • Page 26: Zone Sounds & Timing

    Installation Instructions Zone Sounds & Timing FIELD TITLE and EXPLANATION Single Alarm Sounding Per Zone Select whether or not the system limits alarm sounding to once per arming period for a given zone. UL installations must be 0 (no limit). Fire Alarm Sounder Timeout Select whether or not alarm sounding continues until manually turned off (ignores sounder timeout).

  • Page 27: Dialer Programming

    Dialer Programming FIELD TITLE and EXPLANATION PABX Access Code Enter the PABX code, if used. To clear entries from field, press ∗40∗. If fewer than 6 digits need to be entered, exit by pressing [∗], which advances to the next field. Call Waiting: If the subscriber’s phone service has “call waiting”...

  • Page 28: System Status Report Codes

    ADEMCO Contact ID® Reporting: Enter a digit in the first box to enable the zone to report. Use a different digit for each zone until you have used up available digits. If the number of zones exceeds the number of available digits, begin with digit 1 again.
  • Page 29 FIELD TITLE and EXPLANATION AC Loss Report Code Enter the appropriate report code. Timing of this report is random with up to a 4-hour delay. If AC restores before the report goes out, there is no “AC RESTORE” report. UL: Required for UL commercial burglar alarm installations and required for residential fire alarm installations.

  • Page 30: Miscellaneous System Fields

    Installation Instructions FIELD TITLE and EXPLANATION Test Restore Report Code Enter the appropriate report code, which is sent when the Test mode is exited. UL: Required for UL commercial burglar alarm installations and required for residential fire alarm installations. Miscellaneous System Fields FIELD TITLE and EXPLANATION Daylight Saving Time Start/End Month...
  • Page 31 AAV from taking control of the telephone line, and the AAV “Listen in” session cannot take place. UL installations using the AAV feature must use the ADEMCO UVCM module (part of the ADEMCO UVS system). Exit Delay Restart/Reset must be disabled.

  • Page 32: Pager Programming Fields

    Installation Instructions FIELD TITLE and EXPLANATION Command to Initialize CSID and Subscriber Account Number This is a command function, not a data field. Use this command, if necessary, to reset all subscriber account numbers and the internal CSID to the factory default values. Command to Reset System to Factory Default Values Pressing ∗97 resets all data fields to the factory default values This is a command function, not a data field.

  • Page 33: Configurable Zone Type Programming Fields

    Configurable Zone Type Programming Fields The system allows you to define a custom zone type, based on the options described below. This configurable zone types can be programmed via the downloader or from a keypad using data fields *182-*183 described below. UL installations: Do not configure zones as fire alarm or UL burglar alarm zones.
  • Page 34 Installation Instructions Configurable Zone Type Charts ENTRY 1 ENTRY 2 Response when system disarmed and zone is: Auto Restore Vent Zone Intact EOL Open Shorted RF zone normal RF zone N/A RF zn off-normal INTACT OPEN SHORTED 0 = normal 0 = normal 0 = normal 0 = no...

  • Page 35: Keypad Programming Fields

    Keypad Programming Fields NOTE: Each keypad must be assigned a unique address. Keypads programmed with the same address will give unpredictable results. Address 16 is reserved for keypad 1, which is automatically set with all sounds enabled. FIELD TITLE and EXPLANATION Keypad 2 Device Address 17 *190 Select whether or not this keypad is used, and enter the desired sound option for this keypad.
  • Page 36 Installation Instructions 4-12...

  • Page 37: Menu Mode Programming

    S E C T I O N Menu Mode Programming • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Zone Programming Overview (∗56 and ∗58 Menu Modes) Use 56 Zone Programming to program zones, zone types, report codes, enroll 5800 RF Wireless Transmitter serial numbers, and identify the type of loop input device(s).
  • Page 38 Installation Instructions Enter the report code for this zone, which consists of 2 hexadecimal digits, each in turn 10 Report Code consisting of 2 numerical digits. For example, for a report code of “10,” enter 01 and 00. 1st 01 2nd 00 10 For Contact ID ®...

  • Page 39: ∗ 58 Expert Programming Mode Procedures

    (zone number, zone type, loop number, etc.) relevant to that device. ∗ 58 Expert Programming Mode Procedures This method is designed for use by installers with previous experience in programming ADEMCO control panels. This mode is also used to program wireless keys using pre-defined templates.

  • Page 40: Wireless Key Programming Templates

    Installation Instructions A summary screen with the selected zone’s current programming appears. Zn ZT RC IN: L Begin programming zone information as follows: 00 10 RF 1 Enter Zone Type (ZT; see Zone Types listed in *56 Menu Mode “Zone Type” prompt), Report Code (RC), and Input Device Type (IN)* sequentially (Loop Number (L) is entered at the next prompt).
  • Page 41 Manually enter the serial number printed on the label for the wireless key or press and INPUT S/N release the button to transmit its serial number. AXXX-XXXX – Press [∗] to accept the serial number. The system will check for duplicate. If necessary, press the [#] key to back up without saving, and re-enter the serial number.

  • Page 42: Output Device Programming Overview (*79/*80 Menu Mode)

    Installation Instructions Output Device Programming Overview (*79/*80 Menu Mode Output Devices: The system supports up to 4 relays plus 2 built-in trigger outputs. These “output devices” are assigned to system-wide output numbers (01-04, 17, 18). Relays are identified by the relay module’s device address and the relay position on the module (i.e.

  • Page 43: *80 Menu Mode: Defining Output Functions

    *80 Menu Mode: Defining Output Functions Use this mode to program output function definitions (up to 12 functions) that provide automated control of any of the output devices, based on events occurring on individual zones or zones with certain zone types. Each output definition is identified by an output function number, and includes the following components: Output Definition Components Component...
  • Page 44 Installation Instructions “A” If zone list was selected, this screen appears. Otherwise skip to the next prompt. 01 Zn List Enter the desired zone list number associated with this output number: 01-08 = zone list (Do not use pager zone list 09 in output definitions) Enter the zone list event that will activate this output: 0 = restore;...

  • Page 45: Zone List Overview (∗81 Menu Mode)

    Zone List Overview (∗81 Menu Mode) Zone lists let you group individual zones for use with certain system actions. The following table shows the available zone lists and their purposes: List No. Used for… 1, 2 general purpose chime-by-zone cross zones night stay zones 6, 7, 8 general purpose...

  • Page 46: Function Key Programming Overview (∗57 Menu Mode)

    Installation Instructions Function Key Programming Overview (∗57 Menu Mode) The system provides the ability to program each of the four keypad function keys to perform one of 12 system operations. The end user can then activate the function by simply pressing and holding the programmed key for 2 seconds.

  • Page 47: About Descriptor Programming Overview (∗82 Menu Mode)

    About Descriptor Programming Overview (∗82 Menu Mode) The system lets you assign zone descriptors for protection zones, keypad panics, and RF receiver supervision faults. Each description can be composed of a combination of words (up to 3) selected from a vocabulary of 196 words stored in memory (see a following page). In addition, up to 10 installer-defined words can be added to those already in memory.

  • Page 48: Adding Custom Words

    Installation Instructions Enter the 3-digit number for the next word. In the example, the word is DOOR, whose Z N 0 1 B A C K number is “057.” D O O R See index for entries. [∗] to continue Save second word of descriptor: Z N 0 1 B A C K 6 = save word and go to next word in this descriptor...
  • Page 49 Section 19 - Alpha Descriptor Programming ALPHA VOCABULARY LIST (For Entering Zone Descriptors) • 162 ROOM ∗ (Word Space) • 059 DOWN LEVEL • 219 WING • 109 LIBRARY ∗ WIRELESS • 060 DOWNSTAIRS ROOF – A – DRAWER – X – •...

  • Page 50: Programming Installer And User Schedules

    Installation Instructions Programming Installer and User Schedules The system provides 2 schedules (one for the installer, one for the end user), which can be used to control 11 types of system events at pre-defined times. Start Scheduling mode by entering installer code + [#] + [6] [4] while in normal operating mode. NOTE: The master code can only access schedules 01 and events 00-07.
  • Page 51 This prompt appears if event “2” (user access) was selected. Otherwise it is skipped. G R O U P N U M B E R 1-8 = group number [∗] to continue to the “Start” prompt Enter the event’s start time and days of the week to occur. S T A R T S M T W T F S 01-12 = hour;...
  • Page 52 Installation Instructions 5-16...

  • Page 53: System Communication And Operation

    3 (or 4) times and is followed by the second digit. This is the “expanded” digit. 4+2 Format Comprises a 4-digit subscriber number and 2-digit report code. ADEMCO Contact ID Comprises a 4 or 10-digit subscriber number (depending on format Reporting Format selected), 1-digit event qualifier (“new” or “restore”), 3-digit event code, and 3-digit zone number, user number, or system status number (see the following page).
  • Page 54 Installation Instructions The following table lists codes for reports sent in different formats: Code for Code for Type of 3+1/4+1 3+1/4+1 Code for Report Standard Expanded Alarm SSS(S) A SSS(S) A SSSS AZ AAA(A) Z Trouble SSS(S) T SSS(S) T SSSS Tt TTT(T) t Bypass...

  • Page 55: Ademco Contact Id

    ® Ademco Contact ID ® The Ademco Contact ID Reporting Format comprises the following: 4-digit or 10-digit subscriber number (depending on format selected. 1-digit event qualifier (“new” or “restore”). 3-digit event code. 3-digit zone number, user number, or system status number (see the following page).

  • Page 56: User Security Codes

    Installation Instructions User Security Codes The system supports up to 16 security codes, which can each be assigned one of 4 authority levels. The authority level determines the functions each code can perform as follows: Authority Levels (authority levels can be assigned to users 3-16 only; users 1 and 2 cannot be changed) Level User No.
  • Page 57 Keypad Commands Function Description Silence alarms Pressing any key will silence the keypad sounder for 10 seconds. Disarming the system will silence both keypad and external sounders. If enabled (field ∗21), you can press [#] in place of the system's security code, plus Quick Arm the desired arming key (Away, Stay, Instant, Maximum) Single-Button arming...

  • Page 58: Various System Trouble Displays

    Installation Instructions Various System Trouble Displays Alpha Display Fixed Disp. Meaning CANCELED ALARM will appear if an exit or interior zone contained a fault during closing at the time the Exit Delay ended (e.g., exit door left open), but the system was disarmed during the Entry Delay time.

  • Page 59: Testing The System

    S E C T I O N Testing the System • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • About Test Procedures After the installation is complete, you should perform the following tests: System Test:...

  • Page 60: Go/No Go Test Mode

    Installation Instructions NOTES: • All BR type units must physically be activated to clear the display. • When one button of a transmitter (RF, UR, or BR) is activated, all zones assigned to other buttons on that transmitter are cleared. This also applies to 5816 and 5817 transmitters, which have multiple loops (zones).

  • Page 61: Specifications & Accessories

    SECURITY CONTROL Physical: 12-1/2” W x 14-1/2” H x 3” D (318mm x 368mm x 76mm) Electrical: VOLTAGE INPUT: 16.5VAC from plug-in 25VA transformer, Ademco No. 1321 (in U.S.A.) RECHARGEABLE BACKUP BATTERY: 12VDC, 4AH (sealed lead acid type). Charging Voltage: 13.8VDC.

  • Page 62: 5800 Series Transmitter Input Loop Identification

    Installation Instructions 5800 Series Transmitter Input Loop Identification All of the transmitters illustrated below have one or more unique factory assigned input (loop) ID codes. Each of the input loops requires its own programming zone (e.g., a 5804's four inputs require four programming zones). NOTE: For information on any transmitter not LOOP 3 LOOP...
  • Page 63 Compatible 5800 Series Transmitters Table (continued) Model Product Input Type Description Has three unique input (loop) codes: one for a “Primary” contact 5817 Multi-Point Universal loop with programmable options; the others for two “auxiliary” Transmitter closed circuit contact loops. • Reed switch magnetic contact sensor; easily hidden in the frame 5818 Recessed and edge of a door or window.
  • Page 64 Installation Instructions...

  • Page 65: Regulatory Agency Statements

    S E C T I O N Regulatory Agency Statements • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •...
  • Page 66 Installation Instructions UL NOTICES 1. Entry Delay No. 1 and No. 2 (fields 35, 36) cannot be greater than 30 seconds for UL Residential Burglar Alarm installations, and entry delay plus dial delay should not exceed 1 minute. For UL Commercial Burglar Alarm installations, total entry delay may not exceed 45 seconds.

  • Page 67: Limitations And Warranty

    S E C T I O N Limitations and Warranty • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • WARNING THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced design security system, it does not offer guaranteed protection...
  • Page 68 Installation Instructions WARNING THE LIMITATIONS OF THIS ALARM SYSTEM (Continued) The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
  • Page 69 – INDEX – 1321 ........1-1, 2-4 24-Hour Audible Alarm ....3-3 Data Field Programming Procedures No Alarm Response....3-4, 5-8 24-Hour Silent Alarm ....3-3 ..........3-5 Normally Closed Zones....2-6 3+1 and 4+1 Standard Formats. 6-1 Defining Output Functions ..5-7 Normally Open Zones ....2-6 4204 1-2, 2-5, 2-6, 2-9, 3-1, 5-6, 8-1 Descriptor Programming..
  • Page 70 Installation Instructions Tamper Switch .... 2-8, 2-9, 9-2 Vocabulary List ......5-11 Zone Lists ......3-1, 5-9 Telco Line ......2-11, 3 Zone Programming Procedure ...5-1 Test Mode ......7-1, 7-2 Zone Types..3-3, 5-1, 5-4, 5-8 Test Restore Report Code..4-6 Wireless Key Templates....
  • Page 71 Figure 17. Summary of Connections...
  • Page 72 24 months from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply.

Table of Contents