‘All in One’ desktop computers. A standard height bracket is available for implementations in a standard height PCI slot. The ACB-ULTRA.LPCI is a ‘Universal Bus’ adapter, allowing for use in either +5 or +3.3V PCI slots and provides compliance with the PCISIG PCI Bus Specification Revision 2.2/2.3, which requires ATX power support for both 5V and 3.3V.
Before You Get Started What’s Included The ACB-ULTRA.LPCI is shipped with the following items. If any of these items is missing or damaged, please contact Sealevel for replacement. • ACB-ULTRA.LPCI Adapter • 5104 includes low profile PCI bracket • 5104S includes standard size PCI bracket...
Page 5
Optional Items Depending upon your application, you are likely to find one or more of the following items useful for interfacing the ACB-ULTRA.LPCI to real-world signals. All items can be purchased from our website (http://www.sealevel.com) or by calling 864-843- 4343.
Technical Description The ACB-ULTRA.LPCI adapter was designed for seamless integration into any PCI based system. The ACB- ULTRA.LPCI adapter requires a PCI slot, one IRQ, an 8 byte block of I/O address and a 16K block or 256K block of memory address and additionally, the IUSC requires a 256 byte block of memory. The memory range of this adapter can be configured to reside in the lower 1 Megabyte memory only or anywhere in upper memory.
Page 10
1=256K linear block in high memory only, 0=16X16K pages in low or high memory, (0 on power-up) Interface Selection The ACB-ULTRA.LPCI supports a variety of electrical interfaces. Reference the Control and Status Registers Defined section of this manual for this bit description. There is line termination on RXD, RXC, and TXC in the following modes: RS-530, RS-530A, RS-485T, and V.35.
Page 11
The ACB-ULTRA.LPCI input/output signals are directly generated via the Zilog 16C32 IUSC. The following table defines these signals, their origin pin and signal name following the conventions set by the 16C32 user’s manual. If using a Sealevel Systems, Inc. supplied driver, this is for informational use only. Signal...
Page 12
In all modes, Pin 1 has a 1K ohm resistor to GND and pin 25 has a 1K ohm resistor to +5V connection. This is useful for RS-485 biasing. If this presents a problem in your implementation, please contact Sealevel Systems’...
10 to 90% R.H. Non-Condensing Manufacturing All Sealevel Systems Printed Circuit boards are built to UL 94V0 rating and are 100% electrically tested. These printed circuit boards are solder mask over bare copper with either Electroless Nickel Immersion Gold (ENIG) or Hot Air Solder Leveled (HASL) finish.
No two adapters can occupy the same I/O address. 6. Try the Sealevel Systems adapter with a unique IRQ. While the Sealevel Systems adapter does allow the sharing of IRQs, many other adapters (i.e., SCSI adapters and on-board serial ports) do not.
When calling for technical assistance, please have your user manual and current adapter settings. If possible, please have the adapter installed in a computer ready to run diagnostics. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many common questions. This section can be found at http://www.sealevel.com/faq.asp.
0 (space) and -12 volts (-3 to -10 volts) denotes a binary 1 (mark). The RS-232 and the EIA/TIA-574 specification defines two type of interface circuits, Data Terminal Equipment (DTE) and Data Circuit- Terminating Equipment (DCE). The Sealevel Systems adapter is a DTE interface. RS-422 The RS-422 specification defines the electrical characteristics of balanced voltage digital interface circuits.
Sealevel's commitment to providing the best I/O solutions is reflected in the Lifetime Warranty that is standard on all Sealevel manufactured I/O products. We are able to offer this warranty due to our control of manufacturing quality and the historically high reliability of our products in the field. Sealevel products are designed and manufactured at its Liberty, South Carolina facility, allowing direct control over product development, production, burn-in and testing.