Related Manuals for SeaLevel ACB-232.LPCI
Summary of Contents for SeaLevel ACB-232.LPCI
- Page 1 ACB-232.LPCI USER MANUAL Part # 5103 Sealevel Systems, Inc Phone: (864) 843-4343 P.O. Box 830 FAX: (864) 843-3067 Liberty, SC 29657 USA www.sealevel.com...
-
Page 2: Table Of Contents
D - S ......................8 PPENDIX CREEN E - C ..................9 PPENDIX OMPLIANCE OTICES ................9 EDERAL OMMUNICATIONS OMMISSION TATEMENT EMC D ........................9 IRECTIVE TATEMENT ...........................10 ARRANTY © Sealevel Systems, Inc. SL9075 Revision 7/2006 Sealevel Systems, Incorporated. All rights reserved. -
Page 3: Introduction
Z85230 (ESCC™), which is suitable for the most popular communication protocols including HDLC/SDLC, X.25, Bi-Sync, Mono-Sync, and asynchronous. The ACB-232.LPCI is compliant with EIA/TIA-232E. What’s Included The ACB-232.LPCI is shipped with the following items. If any of these items are missing or damaged, contact the supplier. • ACB-232.LPCI Adapter •... -
Page 4: Technical Description
Technical Description Technical Description The ACB-232.LPCI utilizes the Zilog 85230 Enhanced Serial Communications Controller (ESCC). This chip features programmable baud rate, data format and interrupt control. Refer to the ESCC Users Manual for details on programming the 85230 ESCC chip. -
Page 5: Pin Connector Signal Layouts (Db-25 Male)
Technical Note: Please terminate any control signals that are not going to be used. The most common way to do this is connect RTS to CTS and RI. Also, connect DCD to DTR and DSR. Terminating these pins, if not used, will help insure you get the best performance from your adapter. Sealevel Systems ACB-MP.PCI Page 3... -
Page 6: Specifications
Rating Mean Time Between Failures (MTBF) Greater than 150,000 hours. (Calculated) Physical Dimensions Board length 4.721 inches (11.99 cm) Board Height including Goldfingers 2.536 inches (6.44 cm) Board Height excluding Goldfingers 2.211 inches (5.62 cm) Sealevel Systems ACB-MP.PCI Page 4... -
Page 7: Appendixa - Troubleshooting
2. Make sure the Sealevel Systems adapter is securely installed in a PCI slot. 3. Use the supplied software and User Manual to verify that the Sealevel Systems adapter is configured correctly. 4. Windows users can use the installed programs in the SeaMAC folder to verify operation. -
Page 8: Appendixb - How T O Get Assistance
2. When calling for technical assistance, please have your user manual and current adapter settings. If possible, please have the adapter installed in a computer ready to run diagnostics. 3. Sealevel Systems provides an FAQ section on its web site. Please refer to this to answer many common questions. This section can be found at http://www.sealevel.com/faq.htm... -
Page 9: Appendixc - Electrical Interface
(usually +3 to +10 volts) represents a binary 0 (space) and -12 volts (-3 to -10 volts) denotes a binary 1 (mark). The RS-232 and the EIA/TIA-574 specification defines two type of interface circuits, Data Terminal Equipment (DTE) and Data Circuit-Terminating Equipment (DCE). The Sealevel Systems adapter is a DTE interface. Sealevel Systems ACB-MP.PCI... -
Page 10: Appendixd - Silk -Screen
Appendix D - Silk-Screen Appendix D - Silk-Screen 2.536" 4.721" Sealevel Systems ACB-MP.PCI Page 8... -
Page 11: Appendixe - Compliance Notices
Always use cabling provided with this product if possible. If no cable is provided or if an alternate cable is required, use high quality shielded cabling to maintain compliance with FCC/EMC directives. Sealevel Systems ACB-MP.PCI Page 9... -
Page 12: Warranty
Sealevel Systems assumes no liability for any damages, lost profits, lost savings or any other incidental or consequential damage resulting from the use, misuse of, or inability to use this product. Sealevel Systems will not be liable for any claim made by any other related party.