Advertisement
Quick Links
Operation Manual
Electric Belt Sander File
61117
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 61117
Summary of Contents for WilTec 61117
- Page 1 Operation Manual Electric Belt Sander File 61117 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
- Page 2 All rights re- served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Keep your work area clean and well lit. Untidy and dark areas lead to accidents. • Do not operate power tools in explosive atmospheres, e.g., in presence of flammable liquids, gases, or dust. Power tools create sparks which might ignite dust or fumes. © by WilTec Wildanger Technik GmbH Item 61117 Page 3 http://www.WilTec.de http://www.aoyue.eu...
- Page 4 • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to get stuck and therefore easier to control. © by WilTec Wildanger Technik GmbH Item 61117 Page 4 http://www.WilTec.de http://www.aoyue.eu...
- Page 5 Wear gloves when working with metal work pieces. • It is recommended that the tool always be protected by a residual current device with a rated residual current of 30 mA or less. © by WilTec Wildanger Technik GmbH Item 61117 Page 5 http://www.WilTec.de http://www.aoyue.eu...
- Page 6 Before the first use, the sanding arm needs to be placed to the tool. • straight arm (sanding width 13 mm) • curved arm for grooving and sanding in the centre of work pieces and for reaching confined areas © by WilTec Wildanger Technik GmbH Item 61117 Page 6 http://www.WilTec.de http://www.aoyue.eu 2021-1...
- Page 7 Fitting and removing the dust bag (Fig. E) Warning: Make sure to remove the dust bag before using the tool on metal work pieces. © by WilTec Wildanger Technik GmbH Item 61117 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 3. Refit the dust bag onto the tool. If necessary, the dust bag can be removed from its frame and can be washed. Let it dry before refitting it. © by WilTec Wildanger Technik GmbH Item 61117 Page 8 http://www.WilTec.de http://www.aoyue.eu...
- Page 9 All maintenance should only be carried out by a qualified person. If the supply cord is damaged, it must be replaced by an authorised specialist with an especially pre- pared electricity cable to avoid a safety hazard. © by WilTec Wildanger Technik GmbH Item 61117 Page 9 http://www.WilTec.de...
- Page 10 Ventilation openings and switch levers must be kept clean. Do not attempt to clean them by inserting pointed objects through openings. No chemical agent is allowed to be used in cleaning the power tool. © by WilTec Wildanger Technik GmbH Item 61117 Page 10 http://www.WilTec.de...
- Page 11 Exploded view © by WilTec Wildanger Technik GmbH Item 61117 Page 11 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 12 24 Straight belt arm 25 Soft pad Soft pad 26 Pad 27 Pulley Dust bag 28 Bearing Coil 29 Axes Capacitor 30 Spring Spring 31 Small spring © by WilTec Wildanger Technik GmbH Item 61117 Page 12 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 13 This logo indicates that this electric equipment must not be disposed with the domestic waste. The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE- registration number DE45283704. Disposal of used electrical and electronic appliances...