Related Manuals for Teknik 5420173
Summary of Contents for Teknik 5420173
- Page 1 Teknik www.teknikoffice.co.uk Great for all those books you’ll never read. 5-Shelf Bookcase Barrister Home | Model 5420173 NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
- Page 2 Table of Contents Assembly Tools Required Part Identifi cation No. 2 Phillips Screwdriver Tip Shown Actual Size Hardware Identifi cation Assembly Steps 5-18 Hammer Safety Not actual size Tape Measure Nail Holder (provided) Skip the power trip. This time. Part Identifi cation å...
- Page 3 Now you know Part Identifi cation our ABCs. Page 3...
- Page 4 Hardware Identifi cation å Screws are shown actual size. You may receive extra hardware with your unit. ANGLE BRACKET - 8 HIDDEN CAM - 12 CAM DOWEL - 12 NAIL - 55 HOLE PLUG - 3 METAL PIN - 12 CAM COVER - 8 FURNITURE TIPPING RESTRAINT KIT - 1...
- Page 5 Step 1 Assemble your unit on a carpeted fl oor or on the empty å carton to avoid scratching your unit or the fl oor. Push twelve HIDDEN CAMS (1F) into the ENDS (A2 and B2), å LOWER ENDS (C and D), and BOTTOM (F). Then, insert the metal end of a CAM DOWELS (2F) into the HIDDEN CAMS.
- Page 6 Step 2 Open the FURNITURE TIPPING RESTRAINT KIT (97) and fasten å the SAFETY STRAP to the TOP (E2). Use the provided BLACK Remember: 9/16" LARGE HEAD SCREW. Righty tighty. Lefty loosey. NOTE: Position the SAFETY STRAP exactly as shown. å...
- Page 7 Step 3 Fasten the TOP (E2) to the ENDS (A2 and B2). Tighten å Caution four HIDDEN CAMS. Do not stand the unit upright without the BACK fastened. The unit may collapse. Long fi nished edge Notched edge S u r f a c i t h h o l...
- Page 8 Step 4 Fasten the TOP MOLDING (M25) to the TOP (E2). Use three BLACK 1-1/8" PAN å HEAD SCREWS (9S). NOTE: Do not overtighten the SCREWS into the TOP. å Insert three HOLE PLUGS (14P) into the holes in the TOP MOLDING (M25). å...
- Page 9 Step 5 Fasten the SHELF (G2) to the ENDS (A2 and B2). Use four å BLACK 1-15/16" FLAT HEAD SCREWS (113S). Don't worry. It isn't Rome. This can be built in a day. Long fi nished edge r f a w i t l e s 113S...
- Page 10 Step 6 Fasten the LOWER LEFT END (D) to the SHELF (G2). å Tighten two HIDDEN CAMS. Maximum Arrow 210 degrees Fasten the BOTTOM (F) to the LOWER LEFT END (D). å Tighten two HIDDEN CAMS. Minimum 190 degrees Notched edge i t h f a c S u r...
- Page 11 Step 7 Fasten the LOWER RIGHT END (C) to the BOTTOM (F) å and SHELF (G2). Tighten four HIDDEN CAMS. Maximum Arrow 210 degrees Slide the LOWER END MOLDINGS (P)* onto the notched å edges of the LOWER ENDS (C and D). Minimum * U.S.
- Page 12 Step 8 Fasten fi ve ANGLE BRACKETS (27G) to the LOWER ENDS (C and D) and å BOTTOM (F). Use fi ve BLACK 9/16" LARGE HEAD SCREWS (1S). NOTE: Be sure the ANGLE BRACKETS are even with the edges of the å...
- Page 13 Step 9 Fasten three ANGLE BRACKETS (27G) to the SHELF (G2). å Caution Use three BLACK 9/16" LARGE HEAD SCREWS (1S). Do not stand the unit upright without the Fasten the SKIRT (O) to the SHELF (G2). Use three å BACK fastened.
- Page 14 Step 10 Unfold the LARGE BACK (H2) and lay it over your unit. å Make equal margins along all four edges of the LARGE BACK (H2). Push on opposite corners of your unit if needed to å make it "square". A perforation in the LARGE BACK (H2) has been provided for access to the SAFETY STRAP.
- Page 15 Step 11 Position the BACK (I) over the lower portion of your unit, making equal margins along the bottom å and side edges. Fasten the BACK (I) to the bottom and side edges of your unit using the NAILS (1N) using the Nail å...
- Page 16 Step Step 12 å Carefully stand your unit upright in its fi nal position against a wall. å NOTE: Do not turn the SAFETY DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY STRAP to a wall stud, go to your local hardware store for proper hardware. å...
- Page 17 Step 13 Slide and center a SHELF MOLDING* (N) onto the notched å edge of one of the ADJUSTABLE SHELVES (J). Repeat this step for the other ADJUSTABLE SHELVES (J). å * U.S. Patent No. 5,499,886 å Insert the METAL PINS (1R) into the hole locations of your å...
- Page 18 Step 14 Using your hammer, gently tap a CAM COVER (13P) onto each visible HIDDEN CAM. å NOTE: Please read the back pages of the instruction booklet for important safety information. å This completes assembly. Clean with a damp cloth. Wipe dry. å...
- Page 19 WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves. •...