Table of Contents
Advertisement
Quick Links
Visit website for
available languages of
this document.
DESCRIPTION
1
2
PHOENIX EX™: for normal to high mounting (11.5 – 23 ft)
PHOENIX EX™XL: for low mounting (6.5 – 11.5 ft)
PHOENIX EX™WIDE: for wide detection field (11.5 – 21 ft)
75.5863.04 PHOENIX EX 20210701
3
1. Explosion-proof housing
2. Microwave sensor
3. Grounding lug
4. Cable port (¾" NPT pipe thread)
5. Adjustable bracket
PHOENIX EX™
Motion Sensor with Explosion-Proof Housing
and Tamper Alert
4
5
Page 1 of 8
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BEA PHOENIX EX
Summary of Contents for BEA PHOENIX EX
- Page 1 4. Cable port (¾” NPT pipe thread) 5. Adjustable bracket PHOENIX EX™: for normal to high mounting (11.5 – 23 ft) PHOENIX EX™XL: for low mounting (6.5 – 11.5 ft) PHOENIX EX™WIDE: for wide detection field (11.5 – 21 ft) 75.5863.04 PHOENIX EX 20210701...
- Page 2 PHOENIX EX™WIDE: 11.5 − 21 ft Detection zone: PHOENIX EX™: 13 x 16 ft @ 16ft; PHOENIX EX™XL: 13 x 6.5 ft @ 8.2ft PHOENIX EX™WIDE: 30 x 11ft @ 21ft. (typical at 30° and field size 9) Min. detection speed:...
- Page 3 SCROLL THROUGH PARAMETERS: press the right push button CHANGE VALUE OF CHOSEN PARAMETER: press the left push button RESET TO FACTORY VALUES: press and hold both push buttons until both LEDs flash 75.5863.04 PHOENIX EX 20210701 Page 3 of 8...
- Page 4 SENSOR OUTPUT N.C. N.O. TRANSIENT SUPPRESSION DEVICE * Tamper Switch location is COM and will operate with N.O. or N.C. outputs. TO USER PANEL Page 4 of 8 75.5863.04 PHOENIX EX 20210701...
- Page 5 (see pg. 6) RESETTING TO FACTORY VALUES: FACTORY VALUES POSSIBLE SETTINGS BY PUSH BUTTONS Parameter number Value (factory values) 1 FIELD SIZE 2 HOLD-OPEN TIME 3 OUTPUT CONFIGURATION 4 DETECTION MODE 5 DETECTION FILTER 75.5863.04 PHOENIX EX 20210701 Page 5 of 8...
- Page 6 Always check if the chosen value is optimal for the application. The object size and nature can influence the detection. * The vehicle detection filter increases the response time of the sensor. Page 6 of 8 75.5863.04 PHOENIX EX 20210701...
- Page 7 Batteries in the remote control Check batteries and change if the remote control. are weak or installed improperly. necessary. Can’t find your answer? Visit www.BEAsensors.com or scan QR code for Frequently Asked Questions! 75.5863.04 PHOENIX EX 20210701 Page 7 of 8...
- Page 8 BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose. BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and factory-trained for the type of door/gate system.
Need help?
Do you have a question about the PHOENIX EX and is the answer not in the manual?
Questions and answers