Advertisement
MODEL
1000 - HIGH
1000 - TURNDOWN
GAS TYPE
LPGL
PG
16Mjh
10.9Mjh
NOM. HOURLY GAS CONSUMPTION
1.80kPa
.77kPa
MANIFOLD PRESSURE
1.3mm
INJECTOR SIZE
LUMINAR 1000 LABEL.pdf 1 9/11/2015 9:39:12 AM
Luminar
C
M
1000 Series Gas Log Fire
Y
CM
PRIMARILY A DECORATIVE APPLIANCE, NOT CERTIFIED AS A SPACE HEATER
MY
MODEL
1000 - HIGH
1000 - TURNDOWN
CY
NAT
NAT
GAS TYPE
CMY
20Mjh
13.5Mjh
NOM. HOURLY GAS CONSUMPTION
K
.85kPa
.39kPa
MANIFOLD PRESSURE
2.1mm
INJECTOR SIZE
SPECIFICATIONS
NOTE: LPG VERSIONS SHOW
SPECIFICATIONS FOR LPG APPLIANCES
LIGHTING INSTRUCTIONS WIRING DIAGRAM & WARNING LABELS
THIS GAS LOG FIRE IS SUPPLIED WITH A PRIMARY GUARD FOR YOUR PROTECTION.
THE PRIMARY GUARD MUST BE FITTED WHEN THE UNIT IS OPERATING
THE GLASS FRONT OF THE APPLIANCE IS EXTREMELY HOT WHEN THE UNIT IS RUNNING AND
SEVERE BURNS MAY RESULT THROUGH CONTACT WITH THE GLASS IF THE PRIMARY GUARD
IS NOT FITTED. ADDITIONALLY A SECONDARY FIRE SCREEN MAY BE APPROPRIATE WHEN
SMALL CHILDREN OR THE INFIRM ARE IN THE VICINITY OF THE APPLIANCE.
REMOVAL FOR SERVICING.
To remove the primary guard and door trim or to access the Main Door for removal, simply lift the trim
guard upwards than out towards you. It has 4 tabs which lock into 4 slots. To replace it, fit the bottom tabs
into the slots first, then the top tabs into the top slots and push down to lock into place. (HINT Make sure
the door Allen head bolts above and below the door are tight before trying to remove or replace the door
trim guard. This will make it much easier to to remove or re-fit)
To remove the Main door to access the gas components for servicing, first remove the door trim guard as
above.
Make sure the door Allen head bolts above and below the door are tight before trying to remove the door
trim. Then lift the door guard trim at the base out towards youas explained above.
Now remove the four Allen head bolts bolts that secure the door, Remove the door and set aside.
Australian Made Gas Log Fires
CONTROL IDENTIFICATION
FLAME CONTROL
HI - LO
DO NOT OPERATE THIS APPLIANCE BEFORE
READING THE INSTRUCTION BOOKLET
DO NOT PLACE ARTICLES ON OR AGAINST
THIS APPLIANCE
DO NOT STORE CHEMICALS OR FLAMMABLE
MATERIALS OR SPRAY AEROSOLS NEAR
PILOT
THIS APPLIANCE
DO NOT OPERATE WITH PANELS, COVERS OR
GUARDS REMOVED FROM THIS APPLIANCE
LUMINAR LIGHTING INSTRUCTIONS LABEL.pdf 1 29/10/2015 12:28:37 PM
C
M
Y
CM
MY
CY
CMY
K
PRIMARY GUARD
DOOR REMOVAL
PUSH BUTTON
PIEZO IGNITER
CERTIFICATION NO.
GMK10350
PRESS
TO
TEMPERATURE
AS-4558
IGNITE
ELECTRICAL COMPONENTS
CONFORM TO AS 3100
240V 50HZ 60 WATTS
GAS OFF
PILOT ON
& MAIN GAS ON
SIZE IS 450 X 70mm PART #IL-LUM-COMMON DOOR LABEL
9
CONTROL SWITCH
& remove batteries. Replace batteries & re program
Fan
Fan
High
Low
FAN CONTROL
SWITCH
FASCIA ROCKER
FASCIA ROCKER
WIRING DIAGRAM LUMINAR WITH REMOTE
WIRING DIAGRAM LUMINAR NO REMOTE
SWITCH
SWITCH
LEARN
FM RECEIVER BOX
FAN ROCKER SWITCH
FAN ROCKER SWITCH
BLACK TO
BLACK TO
HIGH
HIGH
HIGH
HIGH
A
BROWN FROM POWER
A
BROWN FROM POWER
LEAD TO ACTIVE "A"
LEAD TO ACTIVE "A"
LOW
LOW
BROWN FROM
BROWN FROM
LOOM TO LOW
NOTE: WHITE WIRE NOT USED
LOOM TO LOW
NOTE: WHITE WIRE NOT USED
CONNECT TO
TPTH AND TH ON
THE GAS VALVE
BROWN
BROWN
BLACK
BLACK
BROWN
BROWN
OVER TEMPERATURE
OVER TEMPERATURE
CONNECT TO TPTH AND TH
CUTOUT SWITCH
CUTOUT SWITCH
ON THE GAS VALVE
LCSII-LUMINAR SERIES OCT 2015
REMOTE
To replace batteries in remote receiver,
first remove the 2 screws below & lift off
receiver box cover. Unclip battery box cover
remote receiver.
PART # IL-LUM-1000
Advertisement
