Anderson Fusion720 Operator's Manual
  1. Manuals
  2. Brands
  3. Anderson Manuals
  4. Farm Equipment
  5. Fusion720
  6. Operator's manual

Anderson Fusion720 Operator's Manual

Round bale wrapper
Hide thumbs Also See for Fusion720:
Table of Contents

Advertisement

Quick Links

Download this manual
404683-1
Round Bale Wrapper
Fusion720
Operator's Manual
ORIGINAL NOTICE — 2021

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Fusion720 and is the answer not in the manual?

Questions and answers

Related Manuals for Anderson Fusion720

Summary of Contents for Anderson Fusion720

  • Page 1 404683-1 Round Bale Wrapper Fusion720 Operator's Manual ORIGINAL NOTICE — 2021...

  • Page 3: Table Of Contents

    Resetting the bale counters Table of contents Autopilot system (option) How to reach us Troubleshooting Starting guidelines Hydraulic controls Anderson limited warranty Sensors About this manual Example with the loading roller high position sensor Introduction Overview Common problems Technical specifications...

  • Page 4: How To Reach Us

    Website: www.grpanderson.com obligation. In no event will Anderson be liable for any Starting guidelines incidental or consequential damages or injuries, including but not limited to loss of profits, rental of...
  • Page 5 Anderson in the shortest possible time. Air, Next Day Air, equipment. Priority and other special shipment methods requested by the dealer will be at the customer’s The warranty is limited to 1 year (12 months). This expense.

  • Page 6: About This Manual

    Before using the wrapper, take the time to thoroughly read the engine manual. Anderson Group is in no way responsible for the content of the engine manual. Conventions “Danger!”...

  • Page 7: Introduction

    Component Description 1 Introduction Fuel tank Congratulations! You have just acquired an Anderson Engine wrapper, a quality machine designed specifically for Pivoting axle wrapping round bales individually or in tubes. Steering axle 1.1 Overview Figure 1 — Main Components of the Wrapper The following figure shows the main components of the Fusion wrapper.

  • Page 8: Technical Specifications

    1.2 Technical specifications system Pressure: 2,100 psi (145 bar) (max.) Rate: 41.8 Lpm (10.836 gpm) Tank capacity (for oil changes): 36 to 40 litres (7.9 to 8.8 gallons) Figure 4 — Dimensions Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 9: Machine Identification

    1.4 Safety and operating pictograms Component Specification Tires Front The Fusion720 wrapper has a number of pictograms that illustrate the main safety and maintenance considerations. Dimensions: 29X12.5-15 NHS Ensure that you see and understand them. Recommended pressure: 30 psi (2...
  • Page 10 Risk of being caught or crushed by the stretchers (moving parts). Remain at a safe distance from the stretchers. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 11 Spears extend Wrapper mode selection: Clockwise rotation: Transport or Wrapping Spears retract Control for the hoop speed and number of film layers in Inline wrapping mode Right bale guide position marker Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 12: Tips And Recommendations For High-Quality Sil

    The hay must be used ity silage within 3 months of being wrapped. The Anderson round bale wrapper is the ideal machine for How do you do the pressing properly? excellent silage. However, for the best possible bales, you...

  • Page 13: Safety Precautions

    2 Safety precautions people, animals or objects other than those for which the wrapper was designed. Your Anderson wrapper was designed to minimize risk to Never attempt to remove material from the the operator. Nevertheless, it must only be used for its equipment before it has come to a complete stop.
  • Page 14 The machine must only be used, maintained and physician. repaired by people who are familiar with its Carefully follow safety label instructions on toxic features and know how to operate it safely. substance containers. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 15 Ensure that nobody touches the machine until the power lines no longer carry a current. Ask for the power line to be disconnected. Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 16: Safety Tips For Transport

    Make sure that the rear axle steering is locked distribution. Do not exceed the maximum load per (Detail B). axle (see the tractor manufacturer's instructions). Do not exceed the maximum load permitted on the hitching points. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 17: Safety Tips For Maintenance And Troubleshooting

    Use chocks and disconnect remove ensure that the lifting equipment has sufficient control module. lifting capacity. Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 18: Protective Devices For Inline Bale Wrappers Sold In The Province Of Quebec

    If these protectors are removed for transport, maintenance, or storage purposes, Anderson Group wishes to remind that they must reinstalled before using the machine. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 19: Getting Started

    ( Figure 3 , number 12). the area or treat it with herbicide (Roundup) to The engine will not start if the guard is open or the emergency stop button is pushed. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 20 This will result in premature wear on parts such as bearings and tires. To transport it over longer distances, put the wrapper on a trailer. Turn off the engine before moving the wrapper. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 21: Installing The Film Rolls

    The film will then stretch too easily during wrapping, and holes or tears may happen more often. Store the rolls of plastic film in a dry place away from sunlight. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 22 You can also move the hoop without learn how to clean and maintain the completely disengaging the brake. Just stretcher rollers. step on the pedal to lower the brake group and turn the hoop in either direction. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 23 1. Start the engine. 2. Press the green pushbutton to open the plastic cutters. 3. Attach the knot on each of the rolls to the hook on each plastic cutter (see the following figure). Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 24: Connecting The Electrical System

    3. Connect the other end of the 12 V power cord to with the following RAM Mount models: connector A on the control box (see the figure below). Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 25 To install the box directly on the wrapper: 1. Slide the box into the control panel, in the location provided for this purpose. 2. Remove cables C and D and plug connector B into the control panel. Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 26: Adjustments

    2. Place the bale guides in the appropriate position together as possible. The bale tube will then leave the for the diameter or length of the bales to wrap (see the instructions further on). Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 27: Adjusting The Pusher Return (End Of Pushing)

    Generally, you should adjust the hoop starting point so next bale on the wrapper. However, the pusher will sink that it starts turning when the pushed bale is Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 28: Adjusting The Tube Compression Level

    Since there are two rolls, each full turn of the hoop represents two layers of film. For normal wrapping, set the wrapping speed control lever to 8. You will have approximately six layers of film wrapping. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 29: Adjusting The Engine Speed

    Once the spears are in the desired SMART START position, position the handle so that The SMART START function was developed by Anderson the pusher will not touch it during so that the first bales in a tube do not slide on the ground its stroke.

  • Page 30: Operation

    Activates the wrapper's emergency stop. On the main page: Stops the engine. Starts the engine. Opens the main menu. Navigate the menus. Operate the wrapper remotely. Figure 29 — Mode Selection Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 31 (option)" on page 39). Turns the work lights on and off. Stops the engine. Starts individual wrapping or simulates a bale being wrapped in Inline wrapping mode. Starts the engine. Engine speed Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 32 Figure 31 — Inline Wrapping Mode Settings Menu menu ("Resetting the bale (Screens 1 and 2) counters" on page 38). Inputs/Outputs View the status of the sensors (see "Sensors" on page 44). Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 33: Individual Wrapping

    7. On the control screen, select Individual wrapping 33). mode by pressing the lower right button. Figure 34 — Individual Wrapping Mode Button Figure 33 — Remote Control Screen The required configuration screen for wrapping appears. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 34 Select the number of film layers to use on the bales. Figure 36 — Configuration In Progres NOTE: Anderson recommends using 6 layers of plastic The main menu home screen appears once film individually configuration is complete. wrapped bales. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 35: Inline Wrapping

    (see "Moving the wrapper" on page 19). then wrapping begins. The bale is automatically 3. Move the mode selection valve lever to the right, in ejected when the wrapping sequence is complete. Wrapping mode (see "Selecting Wrapping and Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 36 The configuration in progress screen appears. Figure 41 — Inline Wrapping Mode Selection Button The required configuration screen for wrapping appears. Figure 43 — Machine Setup in Progress The main menu homepage will appear once setup is complete. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 37 27 if you want to following figure) so that the last bale is pushed add additional film layers to the farther than the X-Tractor system. joints between the bales). Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 38: Resetting The Bale Counters

    1. Press to access the Settings menu, and 5. Make sure that the steering wheels are straight to then select Statistics. prevent the machine from turning when the tube is released. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 39: Autopilot System (Option)

    (B). 1. While supporting the bottom of the autopilot system sensor, remove the rod that holds it to the The following figure shows the main components of the support. autopilot system. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 40 To calibrate the wheel angle sensor: 1. Turn on the control screen and select Inline wrapping mode. 2. Press to open the Settings screen, then select Autopilot. Figure 54 — Calibrating the Wheels to the Left Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 41 "Moving the wrapper" on page 19). Before using your wrapper with the autopilot system, make sure that all the automatic steering controls are working properly. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 42 Ending the tube Once the wrapper reaches the end of the adjacent tube, its wheels will automatically straighten. You can then end the new tube there or continue it. To continue the tube, Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 43 If the autopilot system is not working properly because the adjacent tube is crooked, use manual operation to make the current tube straight. You can then use the autopilot system for the other tubes. Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 44: Troubleshooting

    ON. To open the sensor status screen, from the Individual or Inline mode settings screen, select Inputs/Outputs. Figure 60 — Hydraulic Control Functions Figure 61 — Sensor Status Screen Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 45: Example With The Loading Roller High Position Sensor

    Detects the spears in extended position If you answer NO, the following screen will appear: MC050-C1P24 Detects the absence of plastic film MC050-C1P25 Detects the hoop position MC050-C1P26 Measures the hoop speed Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 46: Common Problems

    Figure 62 — Sensor Locations guards is not closed. 6.3 Common problems The following table describes the most common problems you may encounter with your wrapper. It also provides Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 47 (see "Adjusting the bale guides" on page 26). The bale is Avoid wrapping bales not dense that are too soft. enough. Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 48 Repair necessary. Add AW 32 hydraulic to the tank. 2. Have hydraulic systems specialists check condition of wheel motor replace it if needed. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 49 6 mm rough. distance is (1/4 in.). not correct. The plastic The teeth Clean the teeth with film is on the brake cleaner. breaking on plastic the plastic cutters are cutters. gummed Anderson Group Round Bale Wrapper – Operator's Manual...
  • Page 50 Some wrapper A hydraulic Disassemble, clean components valve spool and reassemble the are not is blocked. hydraulic valve moving spool. properly. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 51: Maintenance

    Your wrapper must be lubricated with oil in the various places indicated by the label in the following figure: Lubricatio "Lubricatio n" on page Greasing "Greasing" on page 52 Figure 63 — Lubrication Point Marker Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 52: Greasing

    1. Using a marker, draw two horizontal lines 25 cm Figure 65 — Greasing Point Marker (10 in.) apart around the circumference of a film roll. NOTE: Anderson Group recommends using synthetic grease. Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...

  • Page 53: Adjusting The Drive Wheel

    30 psi (2 bar) Steering wheels 36 psi (2.5 bar) Hoop wheel 45 psi (3 bar) 7.7 Filter maintenance Maintenance must be performed on the Fusion wrapper filters at the recommended frequencies. Anderson Group Round Bale Wrapper – Operator's Manual...

  • Page 54: Oil Changes

    NOTE: Anderson Group strongly recommends Engine oil See the See the Honda engine cleaning performing general Honda manual maintenance on the machine before engine storing it for long periods. manual Operator's Manual – Round Bale Wrapper Fusion720 Anderson Group...
  • Page 55 ANDERSON GROUP 5125 De la Plaisance St. Chesterville, QC G0P 1J0 CANADA Email: service@grpanderson.com Phone: 1-819-382-2952 Fax: 1-819-382-2218 www.grpanderson.com...

Table of Contents