Sargent ASSA ABLOY 7800 Installation Instructions

1
C
HECK DOOR PREPARATION
A. Clean out lockbody pocket in edge of
door to assure it is clear of debris. For
Triad Lock also clear debris from
hookbolt pockets and track in edge
of door.
3
I
NSTALL OUTSIDE ESCUTCHEON ASSEMBLY
A. With outside escutcheon
assembly in hand tighten
the retaining nut against
the mounting plate as far
as it will go by hand. To
insure a tight fit in this
assembly, back off
retaining nut just one
notch, until star pattern
B
aligns with square
corners. (see pattern
shown)
4
I &
NSTALL INSIDE ADAPTER PLATE ASSEMBLY
A
Note: This plate assembly
will be circular in shape
on KW1 and LW1 trim
5
I
NSTALL INSIDE ESCUTCHEON
A. Lay inside escutcheon
flush against door face
and screw the inside
escutcheon to the outside
escutcheon using trim
screws.
Do not over tighten.
2
I
NSTALL LOCKBODY
A. Insert lockbody (and
hookbolts for Triad) into door
prep. Check that lockbody fits
easily in door with screw holes
aligned. Secure lockbody to the
door using lockbody screws.
Do not tighten fully at this time.
A
B. Important D. If LE3 or LE4 trim design
Insert spindle skip to step 6. With
into retaining outside lever in the
nut to secure horizontal orientation,
this position. as shown, carefully insert
the mounting posts
C. If a thumbturn
through the door and
tail piece is
lockbody, making sure
C
attached to both
the spindle is engaged in
the inside and
C the lock. Outside
outside escutcheons,
escutcheon assembly
make both tail pieces
should be flush with
shorter by snapping them
door surface.
off at the seam.
A. With adapter and plate C. Secure adapter and plate
assembly in hand repeat with thrubolt screws making
important steps 3A and certain the lock washers are
3B as above. For retaining attached before tightening
nut and spindle only. screws into thrubolt post of
the outside rose assembly.
B. Insert spindle with
Do not over tighten.
adapter and plate into
square hole in lockbody
on inside face of door.
C
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
6
S (
ECURE CYLINDER IF PROVIDED
A. Single Cylinder: Screw cylinder, along
with cylinder spring and blocking ring
behind it (if provided), into escutcheon
and lockbody.
Double Cylinder: Screw both cylinders,
with cylinder spring and collar behind,
into lock so that the cams within the
lock do not touch while the cylinder
face lays flush with collar edge, when
collar is held against the escutcheon
face. Note: It is easier to use a key,
slightly out of position in cylinder, to
B
help screw the cylinder down
completely. Over tightening cylinder
could cause malfunction in lock.
7
I /
NSTALL INSIDE LEVER KNOB
A. Place inside lever/knob horizontally
B. Lever/knob set screw must rest in
A
C. Pull on lever/knob to test if set screw
Important: Test lock for all operations before closing the door.
red color
locking piece
Note: Red color indicates locked side of door
or hold back side (91 and 92 Function).
A7031D
)
B. Secure cylinder in place by tightening the
cylinder retainer through hole in edge of
door (shown) with Phillips screwdriver.
C. Test cylinder for proper operation. If LE3 or
LE4 trim design, return to step 3 to continue.
D. Now tighten the lockbody screws completely.
E. Secure the outside front plate to the
lockbody with front screws.
F. For LE2 or LE4 trim designs, attach outside
escutcheon with small set screws using allen
wrench.
If a cylinder is not included in your lock
function, proceed to step 7
onto spindle. Position lever/knob
edge so it is 1/16" from inside
escutcheon face. Hold lever/knob in
place while securing with set screw.
groove on inside adapter for proper
installation. See illustration.
is properly secured.
HOW TO REVERSE LOCK
LEFT HAND
LEFT HAND
REVERSE
BEVEL
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY
Group company. All rights reserved. Reproduction in whole or in part without the
express written permission of Sargent Manufacturing Company is prohibited.
Face of Door
B
Inside Adapter
Spindle
Lever/Knob
Set Screw - Proper Location
Escutcheon/Rose
DOOR HANDING
INSIDE
RIGHT HAND
OUTSIDE
INSIDE
RIGHT HAND
REVERSE
BEVEL
OUTSIDE
DOOR HANDS DETERMINED FROM OUTSIDE
A7031D