Page 1
DAKE HAND-OPERATED HYDRAULIC PRESS Model 50H INSTRUCTIONAL MANUAL *Model 75H shown. May be slight differences. Read and understand all instructions and responsibilities before operating. Failure to follow safety instructions and labels could result in serious injury. Dake Corporation Phone: 800.937.3253 www.dakecorp.com...
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com TABLE OF CONTENTS DAKE STANDARD LIMITED WARRANTY ............2 RETURN & REFUND POLICY ................4 SAFEGUARDING THE POINT OF OPERATION ........... 5 SPECIFICATIONS ....................6 SAFETY ........................6 SET UP ........................8 FILLING PRESS WITH OIL ................
Purchasers who notify Dake within the warranty period will be issued a Case number and/or a Return Material Authorization (RMA) number. If the item is to be returned per Dake’s request, the RMA number must be clearly written on the exterior packaging. Any item shipped to Dake without an RMA will not be processed.
Page 4
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com Warranty Exceptions: The following conditions are not applicable to the standard limited warranty: (a) Part installation or machine service was not completed by a certified professional, and is not in accordance with applicable local codes, ordinances and good trade practices.
Grand Haven, MI 49417 www.dakecorp.com RETURN & REFUND POLICY Thank you for purchasing from Dake! If you are not entirely satisfied with your purchase, we are here to help. Returns All Dake manufactured / distributed machines, parts and couplings include a 30-day return option. These policies are valid from the date of final shipment to the end user.
ANSI B11.2 - Hydraulic Power Presses - Safety Requirements for Construction, Care, and Use It is important that Dake press users have a clear understanding of their responsibility involving the care and use of their Dake hydraulic press, including point-of-operation safe guards. Dake strongly recommends that Dake press users obtain a copy of the current American National Standard Institute (ANSI) B11.2 standard, for a more complete understanding of their responsibilities.
In the space provided record the serial number and model number of the machine. This information is only found on the black and gold Dake tag shown below. If contacting Dake this information must be provided to assist in identifying the specific machine.
Page 8
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com • This machine is intended to be operated by one person. This person should be conscious of the press ram movement not only for themselves but also for persons in the immediate area of the machine.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com OPERATION CONTROLS Hand Crank: (Part No. 701653) on the side of the press is to assist in lowering and raising the table of the press once the table pins are removed. Do not forget to replace the pins once you have the table at the desired height.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com PRESS NOT HOLDING PRESSURE This condition is nearly always caused by dirt under the pressure ball valve (Part No. 586). See hand pump assembly drawing. Steps to fix: 1. Remove the reservoir drain plug and drain all oil out of the reservoir.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com OTHER TROUBLESHOOTING SYMPTOM CAUSE SOLUTION Oil leaking from 1) Reservoir is over filled. (Item 22) 1) Drain excess oil. piston oil seal. 2) Piston Packing is worn or 2) Replace Piston Packing.
Dake Corporation 1809 Industrial Park Dr Grand Haven, MI 49417 www.dakecorp.com EXPLODED VIEWS & PARTS LISTS HAND PUMP ASSEMBLY Item Item Part Name Part No. Qty Part Name Part No. Qty Pump Body Retaining Ring (3/8”) 43972 Ball Valve (Ø1/2”)
Page 14
Cylinder Gasket 1268 Air Vent Tube (1/4” x Screw Nose – Flat 3”) Screw Nose – V-ram Thumb Screw 43618 Screw – 50H Pipe Plug (1/4” NPTF) 1567 Handwheel 716519 Hex Head Cap Screw 43352 Clamp Ring Assembly (1/2”-13 x 2-1/4”) Piston Bumper Pipe Plug (1/4”)
Please contact factory for current prices. ORDERING INFORMATION Parts are available for direct purchase from Dake or through a distributor. When placing a parts order, you will need to provide the part number, name of part, and model number. All parts shipped F.O.B.