Playback; Pausing/Stopping Playback; Rewinding And Fast-Forwarding (Search); Selecting A Playback File (Skip) - Tascam DR-22WL Reference Manual

6 – Playback

Playback

To start playback in home screen mode, press the PLAY button
in stop mode.
NOTE
You can also select and playback a file in the browse screen.

Pausing/stopping playback

/MENU/8 button. (pause)
To stop playback, press the
When playback was stopped in the middle of a file, the status
icon 9 will appear on screen.
If you press the or button to move to the beginning of
. /
a file and stop playback, is shown.
8
To resume playback from the stop position, press the PLAY
button.

Rewinding and fast-forwarding (search)

During playback when the home screen is open, press and hold
the .// button to search backward/forward.
NOTE
Search speed will increase if you keep holding the .//
button.

Selecting a playback file (skip)

In home screen, press either the . button or the / button
to select the file you want to play.
When you are in the middle of a file and want to return to the
beginning, press the . button. To skip to the previous file,
press the . button.
To skip to the next file, press the / button at the beginning
of in the middle of a file.

Special playback (practice mode)

Practice mode is useful for practicing musical instruments.
To use the practice mode while in stop/pause/playback mode,
set the scene dial to " " in home screen. The PRACTICE screen
will appear with a practice mode.
Loop playback, playback speed change, and key change can be
made in this mode.
Press the F1 button to select the file from the browse screen
you want to playback.
To exit practice mode, change the scene dial to a different
setting.
Press the F2
button to turn input signal monitoring on/off.
When monitoring is off, the
screen. The input signal volume can be adjusted. (See "Adjusting
the input level" on page 17.)
NOTE
File skip will not work in practice mode.
28
TASCAM DR-22WL
icon appears at the top of the

Loop playback

Loop playback allows you to repeat playback of the entire or
part of a file.
8 Set the IN and OUT points
1. In PRACTICE screen, press the F3
(highlight) the LOOP item, and press the F4
loop playback.
2. Move to the loop playback IN point, and press the F2
button.
This position is set as IN (start) point.
The icon will light at the top of the playback position
display bar.
3. Press the F3
button at the loop playback OUT point.
This position is set as OUT (end) point, and the unit will
playback the section between the loop playback IN and OUT
points.
The icon will light at the top of the playback position
display bar.
NOTE
• The I/O Too Short pop-up message will appear when the
IN-OUT points are too close. Please reset by spacing at least
one second in between.
• MP3 files with VBR format may affect the accuracy of the IN
and OUT points settings.
8 Delete the IN and OUT points
In stop mode, press the . button or the / button to skip
to the IN (start) and OUT (end) points.
When stopped, skip to an IN (start) point and press the F2
button to clear that point.
When stopped, skip to an OUT (end) point and press the F3
button to clear that point.
8 Loop playback
Press the F1
button to turn the loop playback function on/
off. When the loop playback function is on, the
the top of the screen. The settings are saved even when the loop
playback function is off.
Loop playback will start as follows, depending on the IN (start)
and OUT (end) points:
Set only the IN (start) point
Set only the OUT (end) point
Set both IN/OUT points
No settings of IN/OUT points
button to select
button to set
icon appears at
Loop playback from IN point w
end of the file
Loop playback from the
beginning of the file w OUT
point
Loop playback between IN - OUT
points
Loop playback from the
beginning until the end of the
file