1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Server
  5. VideoJet 8008
  6. Installation and operating manual

Bosch VideoJet 8008 Installation And Operating Manual

Bosch videojet 8008 installation and operating manual
Hide thumbs Also See for VideoJet 8008:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation and Operating Manual

Advertisement

Table of Contents
loading

Related Manuals for Bosch VideoJet 8008

Summary of Contents for Bosch VideoJet 8008

  • Page 2 Copyright This user guide is the intellectual property of Bosch Security Systems and is protected by copyright. All rights reserved. No part of this document may be reproduced or transmitted for any purpose, by whatever means, electronic or mechanical, without the express written permission of Bosch Security Systems. Release: June 2005 (Firmware version 1.2) ©...

  • Page 3: Table Of Contents

    VideoJet 8008 | Installation and Operating Manual Contents Chapter 1 Preface Conventions ......... 5 Intended use.
  • Page 4 Specifications ........128 Chapter 9 Index Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...

  • Page 5: Chapter 1 Preface

    Preface This user guide is intended for persons responsible for the installation and operation of the VideoJet 8008. International, national and any regional regulations regarding electronics must be followed at all times. Relevant knowledge of network technology is required. The user guide describes the installation and operation of the unit.

  • Page 6: Intended Use

    The VideoJet 8008 network video server transmits video and control signals over data networks (Ethernet LAN, Internet). The integrated hard disk allows the VideoJet 8008 to be used as a DVR. It is designed for use in CCTV systems. By incorporating external alarm sensors, various functions can be triggered automatically.

  • Page 7: Chapter 2 Safety Information

    VideoJet 8008 | Installation and Operating Manual Safety information Electric shock hazard Never attempt to connect the unit to any power network other than the type for which it was intended. Never open the housing! If a fault occurs, disconnect the unit from the mains supply and from all other devices.

  • Page 8: Installation And Operation

    Actions beyond these may lead to personal injury, damage to property or damage to the equipment. Maintenance and repair Never open the casing of the VideoJet 8008. The unit does not contain any user serviceable parts. Ensure that all maintenance or repair work is performed only by qualified personnel (electrical engineering or network technology specialists).

  • Page 9: Chapter 3 Product Description

    VideoJet 8008 | Installation and Operating Manual Product description Components supplied VideoJet 8008 network video server Mains cable Configuration cable Assembly kit for installation in 19" racks Quick start guide in English/German Product CD with the following content: – Quick start guide in English/German –...

  • Page 10: Configuration Requirements

    PC. If necessary, the required software and controls can be installed from the product CD provided (see Components supplied, page 9). Product description Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...

  • Page 11: Overview Of Functions

    CCTV systems or local networks can be achieved quickly and easily. The VideoJet 8008 is designed as a table-top unit and for installation in control cabinets. The assembly kit supplied allows it to be installed in a 19" rack quickly and easily.
  • Page 12 The prerequisite for this is that the UDP and IGMP V2 protocols are implemented on the network. The integrated hard disk allows the VideoJet 8008 to be used as a digital video recorder for local long-term recording.
  • Page 13 VideoJet 8008 | Installation and Operating Manual Summary The VideoJet 8008 provides the following main functions: Video and data transmission over IP data networks Dual Streaming function for the encoder for simultaneous encoding with two individually definable profiles Multicast function for simultaneous picture transmission to multiple receivers...

  • Page 14: Rear Panel Connections

    LED network link (left) and orange LED data traffic (right) 5 Power socket for connecting the mains cable Further information on the LEDs can be found on page 123. Product description Installation and Operating Manual | VideoJet 8008 ... IN Bosch Security Systems | 2005-06 | V2.0...

  • Page 15: Front Panel

    VideoJet 8008 | Installation and Operating Manual Front panel 6 Power LED lights up green when ready for operation 7 IR diode Infrared receiver (for future expansion of functions) 8 HDD LED flashes red during data transmission to and from hard disk...
  • Page 16 EN | 16 Installation and Operating Manual | VideoJet 8008 Product description Bosch Security Systems | 2005-06 | V2.0...

  • Page 17: Chapter 4 Installation

    VideoJet 8008 | Installation and Operating Manual Installation The VideoJet 8008 is designed as a table-top unit and for installation in control cabinets. The assembly kit supplied allows it to be installed in a 19" rack quickly and easily. For table-top operation, four self-adhesive, anti-slip rubber feet are supplied, which can be stuck under the unit.

  • Page 18: Control Cabinet Installation

    EN | 18 Control cabinet installation The VideoJet 8008 is set up for installation in a 19" rack. The necessary assembly kit is included with the unit. Warning! When installing in control cabinets, ensure that each unit has adequate ventilation. The free space around the unit must be at least 5 cm on the right and left sides and at least 10 cm at the rear.
  • Page 19 EN | 19 VideoJet 8008 | Installation and Operating Manual Installation overview Bosch Security Systems | 2005-06 | V2.0 Installation...

  • Page 20: Connections

    Cameras Up to eight standard video sources (e.g. CCTV cameras) can be connected to the VideoJet 8008. Any cameras or other video sources that produce a standard PAL or NTSC signal are suitable. – Connect each of the cameras or other video sources with a video cable (75 ohm) to the BNC jacks Video 1 to Video 8.
  • Page 21 VideoJet 8008 | Installation and Operating Manual Alarm inputs The VideoJet 8008 has ten alarm inputs on the orange terminal block. The alarm inputs are used to connect to external alarm devices, such as door contacts or sensors. With the appropriate configuration, an alarm sensor can, for example, trigger an automatic connection between the VideoJet 8008 and a remote location.

  • Page 22: Turning On/Off

    – Connect the mains cable to a fused mains socket. The green Power LED on the front panel of the VideoJet 8008 lights up. After the boot process, as soon as the text VideoJet 8008 appears in the display the unit is ready to use.

  • Page 23: Setup Using A Terminal Program

    Setup using a terminal program Data terminal You can connect a data terminal to the VideoJet 8008 for setup and local control. The data terminal consists of a computer with terminal software. Use the configuration cable included in the package for this connection.
  • Page 24 ENTER key to transfer the values to the VideoJet 8008. Assigning an IP address To operate the VideoJet 8008 in your network, a valid IP address for the network must be assigned. The following default address has been pre-set at the factory: 192.168.0.1 –...
  • Page 25 The new IP address and a new subnet mask or gateway address will only be valid after restarting. Restart Briefly disconnect the power supply to the VideoJet 8008 (remove connector and re-connect after a few seconds). Additional parameters Using the terminal program, you can check other basic parameters and modify them where necessary.
  • Page 26 EN | 26 Installation and Operating Manual | VideoJet 8008 Installation Bosch Security Systems | 2005-06 | V2.0...

  • Page 27: Chapter 5 Configuration Using A Web Browser

    VideoJet 8008 | Installation and Operating Manual Configuration using a Web Browser Connecting The integrated HTTP server allows the unit to be configured over the network with a web browser. This option is significantly more comprehensive and convenient than configuration using a terminal program and also offers you the option of displaying live video images.
  • Page 28 The following default address has been pre-set at the factory: 192.168.0.1 – Start the web browser. – Enter the IP address of the VideoJet 8008 as the URL. The connection will be established and, after a short time, the LIVEPAGE with the video image will appear.

  • Page 29: Choosing The Configuration Mode

    – Enter the user name and associated password in the corresponding text fields. – Click OK. If the password is correct, the desired page is displayed. Choosing the configuration mode There are two options for configuring the VideoJet 8008 or checking the current setup: the unit overview or the configuration menu.
  • Page 30 EN | 30 Installation and Operating Manual | VideoJet 8008 Beginning configuration Click on the SETTINGS link in the upper section of the LIVEPAGE window. A new page containing the configuration menu (see Configuration menu, page 58) and the unit overview (see Unit overview, page 31) is opened.

  • Page 31: Unit Overview

    VideoJet 8008 | Installation and Operating Manual Unit overview The unit overview gives you a graphical overview of the individual areas of the configuration. The individual configuration parameters are grouped and displayed in separate windows. You can access the individual areas directly.
  • Page 32 Selecting a profile You can adapt the MPEG 4 data transmission to the operating environment (for example network structure, bandwidth, data structures). The VideoJet 8008 provides Dual Streaming for each of the eight encoders. The advantage of this is that each encoder can simultaneously generate two data streams with different compression settings, for example for transmission and local storage.
  • Page 33 VideoJet 8008 | Installation and Operating Manual Profile 3: High resolution (D1/4CIF) High resolution for high bandwidth connections, resolution 704 × 576/480 pixels Profile 4: DSL For DSL connections at 500 kBit/s, resolution 352 x 288/240 pixels Profile 5: ISDN (2B)
  • Page 34 Therefore it is generally best to use the default profiles. The profiles should only be changed if you are completely familiar Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 35 EN | 35 VideoJet 8008 | Installation and Operating Manual Bosch Security Systems | 2005-06 | V2.0 Configuration using a Web Browser...
  • Page 36 704 × 288/240 pixels D1/4CIF 704 × 576/480 pixels Reset of profile: Click Default to return the profile to the factory default value. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 37 EN | 37 VideoJet 8008 | Installation and Operating Manual Recording settings Here you set the parameters for recording on the local hard disk. Recording may be done continuously or only in the event of an alarm. Partition: Select the partition in which you want to record. A separate partition is used for recording of each video input.
  • Page 38 For each partition and thus for each camera input, there are separate selection fields for each day of the week. You can select 16 individual recording periods for each day of the week. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 39 EN | 39 VideoJet 8008 | Installation and Operating Manual Used file tracks on partition: Up to 128 recording tracks are created automatically on a partition. Each new recording is assigned a separate track. Selecting the Linear mode option (see page 43) means that no more new recordings are made after the 128 tracks have been used.

  • Page 40: Alarm Recording

    EN | 40 Installation and Operating Manual | VideoJet 8008 Alarm recording Here you can define the times when recordings are to be made from the selected camera to the hard disk in the event of an alarm. As for time recording, separate selection fields are available for each partition and thus for each camera input.
  • Page 41 EN | 41 VideoJet 8008 | Installation and Operating Manual The VideoJet 8008 uses a special recording mode for alarm recording to optimize the use of the memory capacity. As soon as a time slot for alarm recording begins, continuous recording starts on a segment the size of a complete alarm sequence (pre- and post-alarm).
  • Page 42 EN | 42 Installation and Operating Manual | VideoJet 8008 Recording status: The icon indicates recording activity on this partition. The icon is animated while recording is in progress. Properties You can view the current parameters for each selected partition and change them as required in the recording scheduler.
  • Page 43 VideoJet 8008 | Installation and Operating Manual Warning! Making changes to a partition causes the affected partition to be reorganized and all sequences stored on it to be lost. Changes to the size (total space in partition) will result in reorganization of the entire hard disk and the loss of all saved data.
  • Page 44 Before deleting recordings, check them and back up any important sequences to your computer's hard drive. – Click Format to delete all recordings on the partition currently selected. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 45 VideoJet 8008 | Installation and Operating Manual System settings Various basic data for the VideoJet 8008 can be set or selected here. Unit identification Unit name: The unit can be assigned a name to assist in identifying it. The name simplifies the management of multiple devices in more extensive systems, for example using the VIDOS software.
  • Page 46 EN | 46 Password A VideoJet 8008 is generally protected by a password to prevent unauthorized access to the unit. You can use various authorization levels to limit the scope of a user's access. Note Proper password protection is only guaranteed if all higher authorization levels are also protected with a password.
  • Page 47 VideoJet 8008 | Installation and Operating Manual Confirm password: Re-enter the new password to rule out typing errors. Note The new password is then saved by clicking the Set button. You should therefore click the Set button immediately after entering and confirming the password, even if you also want to assign a password to another user name.
  • Page 48 Keep a record of these numbers in case technical assistance is required. Hardware version: The hardware version number of the VideoJet 8008 is displayed. Firmware version: The firmware version number of the VideoJet 8008 is displayed. Configuration using a Web Browser...

  • Page 49: Alarm Settings

    Alarm settings Here, you can make the settings for the alarm sources and alarm connections. Alarm sources You can configure the possible alarm triggers for the VideoJet 8008 (for example the alarm inputs). Alarm input 1 … Alarm input 10: Select the option On in order to activate the alarm via the corresponding external alarm sensor.
  • Page 50 Alarm connections You can select the response of the VideoJet 8008 in case of an alarm. In case of an alarm, the VideoJet 8008 can automatically establish a connection to a predefined IP address. You can enter up to ten IP addresses which will be selected in order by the unit in case of an alarm until a connection is established.
  • Page 51 VideoJet 8008 | Installation and Operating Manual Destination IP address: For each number, enter the corresponding IP address for the desired remote location. Destination password: If the remote location is password protected, enter the password here. Auto-connect: Select On if an active connection should be re-established automatically to one of the previously specified IP addresses after each restart, connection breakdown or network failure.
  • Page 52 VideoJet 8008 will be restarted, after which it can only be accessed at the new IP address. IP address: Enter the desired IP address for the VideoJet 8008 in this field. The IP address must be valid for the network. Subnet mask: Enter the appropriate subnet mask for the set IP address here.
  • Page 53 (0.0.0.0). Ethernet link type: If the VideoJet 8008 is connected to the network via a switch, both devices must have the same preset network connection type. If necessary, ask your network administrator what value the associated switch is set to.
  • Page 54 EN | 54 Installation and Operating Manual | VideoJet 8008...
  • Page 55 (duplication of the data streams in the network). With the setting 0.0.0.0 the encoder for the relevant stream operates in multi- unicast mode (copying of data streams in unit). The VideoJet 8008 supports multi-unicast connections for up to five simultaneously connected receivers.
  • Page 56 The serial interface port RS232/485 can be configured for specific requirements. Note If the VideoJet 8008 is working in multicast mode (see page 54), the first remote location to establish a video connection to the unit is also assigned the transparent data connection. However after about 15 seconds of inactivity, the data connection is automatically terminated and another remote location can exchange transparent data with the unit.
  • Page 57 EN | 57 VideoJet 8008 | Installation and Operating Manual Stop bits: Select the number of stop bits per character. Parity check: Select the type of parity check. Interface mode: Select the desired protocol for the serial interface. Half-duplex mode: Choose the setting appropriate for your application.

  • Page 58: Configuration Menu

    EN | 58 Configuration menu The configuration menu allows all parameters of the VideoJet 8008 to be configured. You can view the current settings by opening one of the configuration pages. The settings can be changed by entering new values or by selecting a predefined value in a list field.
  • Page 59 Enter a name that makes it as easy as possible to identify the location unambiguously. Unit ID: Each VideoJet 8008 should be assigned a unique identifier that can be entered here as an additional means of identification. Bosch Security Systems | 2005-06 | V2.0...
  • Page 60 EN | 60 Password A VideoJet 8008 is generally protected by a password to prevent unauthorized access to the unit. You can use various authorization levels to limit the scope of a user's access. Note Proper password protection is only guaranteed if all higher authorization levels are also protected with a password.
  • Page 61 VideoJet 8008 | Installation and Operating Manual Confirm password: Re-enter the new password to rule out typing errors. Note The new password is then saved by clicking the Set button. You should therefore click the Set button immediately after entering and confirming the password, even if you also want to assign a password to another user name.
  • Page 62 VideoJet 8008. Time server The VideoJet 8008 can receive the time signal from a time server using the time server protocol (RFC 868) and then use it to set the internal clock. The device calls up the time signal automatically every ten minutes.
  • Page 63 EN | 63 VideoJet 8008 | Installation and Operating Manual Camera names The camera name makes it easier to identify the remote camera location, in the event of an alarm for example. It will be displayed in the video screen if configured to do so (see page 64).
  • Page 64 A red rectangle indicates that the sequence (live or saved) has been manipulated. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 65 EN | 65 VideoJet 8008 | Installation and Operating Manual Picture settings You can set the video image of each camera to suit your requirements. The current video image is displayed in the small window next to the sliders as confirmation.
  • Page 66 Selecting a profile You can adapt the MPEG 4 data transmission to the operating environment (for example network structure, bandwidth, data structures). The VideoJet 8008 provides Dual Streaming for each of the eight encoders. The advantage of this is that each encoder can simultaneously generate two data streams with different compression settings, for example for transmission and local storage.
  • Page 67 VideoJet 8008 | Installation and Operating Manual Profile 4: DSL For DSL connections at 500 kBit/s, resolution 352 x 288/240 pixels Profile 5: ISDN (2B) For ISDN connections via two B channels, resolution 352 x 288/240 pixels Profile 6: ISDN (1B)
  • Page 68 You can enter a new name for the profile here. The name is then displayed in the lists of available profiles in the MPEG-4 encoder field. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 69 Target data rate: To optimize utilization of the bandwidth in your network, you can limit the data rate for the VideoJet 8008. The target data rate should be set according to the desired picture quality for typical scenes with no excessive motion.
  • Page 70 704 × 288/240 pixels D1/4CIF 704 × 576/480 pixels Reset of profile: Click Default to return the profile to the factory default value. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 71 VideoJet 8008 | Installation and Operating Manual Partitioning Eight partitions can be set up on the VideoJet 8008 hard disk, similar to the partitioning that can frequently be found on computer hard drives. Parameters can be defined individually for each partition, such as size, quality, type of video recording and the compression standard used.
  • Page 72 EN | 72 Installation and Operating Manual | VideoJet 8008 Create partition Warning! Changes to the size or number of partitions will result in reorganization of the entire hard disk and the loss of all saved data. Therefore, before making changes to the parameters mentioned, check the recordings and back up the important sequences to your computer's hard drive.
  • Page 73 – Click Cancel to interrupt the process and close the Wizard. Making changes After you have specified all the settings you want, they must be transmitted to the VideoJet 8008 unit and saved. Click Finish on the last screen of the Wizard to complete this process. Warning! All changes to the settings will only take effect after you have ended the configuration by clicking Finish in the last screen.
  • Page 74 – Go to the last screen of the Wizard if necessary. – Click Finish to finalize the configuration. All settings will be transmitted to the VideoJet 8008 and are in effect afterward. Editing a partition The configuration of a partition can be changed at any time.
  • Page 75 VideoJet 8008 | Installation and Operating Manual – Click Delete partition to delete the selected partition. The display continues to show the line with the associated number, only the partition name is deleted and the size is stated as 0.
  • Page 76 EN | 76 Installation and Operating Manual | VideoJet 8008 Recording scheduler Here you set the parameters for recording on the local hard disk. Recording may be done continuously or only in the event of an alarm. Partition: Select the partition in which you want to record. A separate partition is used for recording of each video input.
  • Page 77 VideoJet 8008 | Installation and Operating Manual The icon at the bottom of the pages indicates recording activity on this partition. The icon is animated while recording is in progress. Recording activity can be stopped at any time, and one, several or all partitions can be deactivated.
  • Page 78 EN | 78 Installation and Operating Manual | VideoJet 8008 the 129th recording will be written on the first track, so that the oldest recording is always overwritten by the newest. Used space on partition: Indicates the percentage of the partition that is already used.
  • Page 79 VideoJet 8008 | Installation and Operating Manual Alarm recording Here you can define the times when recordings are to be made from the selected camera to the hard disk in the event of an alarm. As for time recording, separate selection fields are available for each partition and thus for each camera input.
  • Page 80 EN | 80 Installation and Operating Manual | VideoJet 8008 The VideoJet 8008 uses a special recording mode for alarm recording to optimize the use of the memory capacity. As soon as a time slot for alarm recording begins, continuous recording starts on a segment the size of a complete alarm sequence (pre- and post-alarm).
  • Page 81 VideoJet 8008 | Installation and Operating Manual Recording status: The icon indicates recording activity on this partition. The icon is animated while recording is in progress. Properties You can view the current parameters for each selected partition and change them as required in the recording scheduler. You can also activate the alarms that you want to trigger recording.
  • Page 82 Here you can select the alarm sensors that should trigger an alarm. The video alarm for one camera can also be used to trigger alarm recording by another camera. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 83 VideoJet 8008 | Installation and Operating Manual Note The alarm sensors must be activated for them to be able to trigger recording: You can activate the alarm inputs and video alarms on the Alarm sources page (see page 84). – Click in the checkbox for the alarm sensor you want to trigger a recording.
  • Page 84 EN | 84 Alarm sources You can configure the possible alarm triggers for the VideoJet 8008 (for example the alarm inputs). Alarm input 1 … Alarm input 10: Select the option On in order to activate the alarm via the corresponding external alarm sensor.
  • Page 85 VideoJet 8008 | Installation and Operating Manual Alarm connections You can select the response of the VideoJet 8008 in case of an alarm. In case of an alarm, the VideoJet 8008 can automatically establish a connection to a predefined IP address. You can enter up to ten IP addresses which will be selected in order by the unit in case of an alarm until a connection is established.
  • Page 86 Note The numbering corresponds to the labeling of the video inputs on the rear panel of the unit. Configuration using a Web Browser Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...
  • Page 87 The serial interface port RS232/485 can be configured for specific requirements. Note If the VideoJet 8008 is working in multicast mode (see page 54), the first remote location to establish a video connection to the unit is also assigned the transparent data connection. However after about 15 seconds of inactivity, the data connection is automatically terminated and another remote location can exchange transparent data with the unit.
  • Page 88 EN | 88 Installation and Operating Manual | VideoJet 8008 Parity check: Select the type of parity check. Interface mode: Select the desired protocol for the serial interface. Half-duplex mode: Choose the setting appropriate for your application. Configuration using a Web Browser...
  • Page 89 VideoJet 8008 will be restarted, after which it can only be accessed at the new IP address. IP address: Enter the desired IP address for the VideoJet 8008 in this field. The IP address must be valid for the network. Subnet mask: Enter the appropriate subnet mask for the set IP address here.
  • Page 90 EN | 90 Ethernet link type: If the VideoJet 8008 is connected to the network via a switch, both devices must have the same preset network connection type. If necessary, ask your network administrator what value the associated switch is set to.
  • Page 91 Multicasting In addition to a 1:1 connection between an encoder and a single receiver (unicast), the VideoJet 8008 can enable multiple receivers to receive the video signal from an encoder simultaneously. This is either done by duplicating the data stream in the unit and then distributing it to multiple receivers (multi-unicast) or by distributing an individual data stream in the network itself to multiple receivers in a defined group (multicast).
  • Page 92 EN | 92 Installation and Operating Manual | VideoJet 8008 Configuration using a Web Browser Bosch Security Systems | 2005-06 | V2.0...
  • Page 93 Keep a record of these numbers in case technical assistance is required. Hardware version: The hardware version number of the VideoJet 8008 is displayed. Firmware version: The firmware version number of the VideoJet 8008 is displayed. Bosch Security Systems | 2005-06 | V2.0...
  • Page 94 Internet/Intranet). For access via the Internet/Intranet, there must be a connection in order to display the image. The image files are not stored on the VideoJet 8008. – Mark the checkboxes for the information to be displayed on the LIVEPAGE.
  • Page 95 VideoJet 8008 | Installation and Operating Manual Device logo URL: Enter the path for a suitable image for the upper part of the window (banner) here. The image can be stored on a local computer, a local network or at an Internet address.
  • Page 96 EN | 96 Installation and Operating Manual | VideoJet 8008 Path for event log: Enter the path for saving the event log here. – If necessary, click Search to find a suitable folder. Path for system log: Enter the path for saving the system log here.
  • Page 97 Firmware and configuration upload Firmware update: The VideoJet 8008 is designed in such a way that its functions and parameters can be updated with firmware. To accomplish this, the current firmware package is transferred to the unit via the selected network. The firmware will be installed there automatically.
  • Page 98 /main.htm (for example 192.168.0.80/main.htm). – Repeat the upload. Configuration download: You can save configuration data for the VideoJet 8008 to a computer and load saved configuration data from a computer to the unit. – Click Download. A dialog will appear.

  • Page 99: Function Test

    The VideoJet 8008 offers a variety of configuration options. Therefore you should check that it works properly after installation and configuration. This is the only way to ensure that the VideoJet 8008 will function as intended in the event of an alarm.
  • Page 100 EN | 100 Installation and Operating Manual | VideoJet 8008 Configuration using a Web Browser Bosch Security Systems | 2005-06 | V2.0...

  • Page 101: Chapter 6 Operation

    Operation with Microsoft Internet Explorer A computer with Microsoft Internet Explorer (version 6.0 or later) can be used to receive live images from the VideoJet 8008, control cameras or other peripherals and replay sequences stored on the local hard disk.

  • Page 102: The Livepage

    The following default address has been pre-set at the factory: 192.168.0.1 – Start the web browser. – Enter the IP address of the VideoJet 8008 as the URL. The connection will be established and, after a short time, the Operation...
  • Page 103 Note A VideoJet 8008 offers you the option of limiting access across various authorization levels (see pages 46 and 60). – Enter the user name and the associated password in the appropriate fields.
  • Page 104 Installation and Operating Manual | VideoJet 8008 If a controllable device (such as a dome camera) is configured and connected to the VideoJet 8008, the controls for the device are displayed next to the video image. – To control a peripheral device click the appropriate controls.
  • Page 105 System log / Event log The System log field contains information about the operating status of the VideoJet 8008 and the connection. These messages can be saved automatically in a file (see page 95). Events such as the triggering or end of alarms are shown in the Event log field.

  • Page 106: Saving Snapshots

    – Click the symbol for recording video sequences. Saving begins immediately. The storage location depends on the configuration of the VideoJet 8008 (see page 96). A recording in progress is indicated by the blinking of the red dot on the icon.

  • Page 107: Recordings In Progress

    – If necessary, you can also start the MPEG viewer by double-clicking the file MPEGViewer.exe. Recordings in progress During automatic recording to the hard disk of the VideoJet 8008 by one of the background programs, the hard disk icon below the MPEG video image on the LIVEPAGE changes.

  • Page 108: The Media-Replay Page

    EN | 108 The MEDIA-REPLAY page The integrated hard disk allows the VideoJet 8008 to be used as a digital video recorder for local long-term recording. The MEDIA-REPLAY page for playing back recorded video sequences can be reached from the LIVEPAGE or from the SETTINGS.

  • Page 109: Playback Control

    VideoJet 8008 | Installation and Operating Manual Playback control A time bar is shown below the video image to indicate the progress of the sequence. If a particular sequence has been selected for playback by clicking it, the selected sequence is highlighted in blue in the list with a green frame. The associated time segment is shown in gray in the bar.
  • Page 110 MEDIA-REPLAY page; they are not saved along with the sequences. As soon as you exit the page, all bookmarks are deleted. Operation Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...

  • Page 111: Backup

    VideoJet 8008 | Installation and Operating Manual Backup You can back up video sequences or individual images saved on the VideoJet 8008 hard disk to your computer's hard disk. First select the sequence to save as described above. The following buttons are available for backup:...

  • Page 112: Installing Mpeg Viewer

    – Open the MPEG Viewer directory and copy the file MPEGViewer.exe to your computer's hard drive. – If necessary, you can also start the MPEG viewer by double-clicking the file MPEGViewer.exe. Operation Installation and Operating Manual | VideoJet 8008 Bosch Security Systems | 2005-06 | V2.0...

  • Page 113: Hardware Connections Between Video Servers

    VideoJet 8008 | Installation and Operating Manual Hardware connections between video servers A VideoJet 8008 with a camera connected to it can be used as a transmitter and a compatible MPEG-4 hardware decoder (such as the VIP XD) with a connected monitor as a receiver using an Ethernet network connection.
  • Page 114 – Use the web browser to connect to the receiver. Its home page will be displayed. – Under Video sources on the page CONNECTIONS, select the VideoJet 8008. A JPEG snapshot of the video source selected will be displayed on the page. – Set the video input you want the images to come from.

  • Page 115: Operation With Decoder Software

    X icon to end the display of the video images on the connected monitor. Operation with decoder software The VideoJet 8008 video server and VIDOS software combine to provide a high- performance system solution. VIDOS is software for operating, controlling and administering CCTV installations (such as surveillance systems) at remote locations.

  • Page 116: Controls On The Front Panel

    EN | 116 Controls on the front panel The VideoJet 8008 has various controls and indicators on the front panel (see page 15). You can show some of the most important configuration parameters in the display. However, it is not possible to change the parameters here.
  • Page 117 Input pin states Shows the alarm inputs at which an alarm is currently available (indicated by H). EthTX EthRX Current data transmission rate from and to the VideoJet 8008. HDD Throughput Current recording speed to the VideoJet 8008 hard disk. SW version Firmware version number for VideoJet 8008.
  • Page 118 EN | 118 Installation and Operating Manual | VideoJet 8008 Operation Bosch Security Systems | 2005-06 | V2.0...

  • Page 119: Chapter 7 Maintenance And Upgrades

    IP address, subnet mask and gateway address. Restart (reset) If necessary, you can restart the VideoJet 8008, for example if the unit is no longer responding. All settings are retained. – In the address bar of the web browser, enter /reset after the unit IP address (for example 192.168.0.80/reset).

  • Page 120: Repairs

    EN | 120 Repairs Warning! Never open the casing of the VideoJet 8008. The unit does not contain any user serviceable parts. Ensure that all maintenance or repair work is performed only by qualified personnel (electrical engineering or network technology specialists). In case of doubt, contact your dealer's technical service center.

  • Page 121: Chapter 8 Appendix

    VideoJet 8008 | Installation and Operating Manual Appendix Troubleshooting If you cannot resolve a fault, please contactyour supplier or system integrator or go direct to Bosch Security Systems Customer Service. The version numbers of the internal processors can be viewed on a special page.
  • Page 122 Power failure during operational after programming by the update firmware upload. file. Incorrect update file. Appendix Installation and Operating Manual | VideoJet 8008 Solution Check all configuration parameters. Check all cables, plugs, contacts and connections. Check the IP addresses (terminal program).

  • Page 123: Leds

    VideoJet 8008 | Installation and Operating Manual LEDs The VideoJet 8008 video server is equipped with several LEDs that show the operating status and can give indications of possible malfunctions: Power Not lit: Lit green: Flashing green: Flashing red: Fail...

  • Page 124: Rs232/485 Interface

    CTS (clear to send) – – GND (ground) – TxD (transmit data) RTS (ready to send) Appendix Installation and Operating Manual | VideoJet 8008 RS422/485 standard RxD+ (receive data plus) RxD- (receive data minus) – – GND (ground) – TxD- (transmit data minus) TxD+ (transmit data plus) Bosch Security Systems | 2005-06 | V2.0...

  • Page 125: Terminal Block

    VideoJet 8008 | Installation and Operating Manual Terminal block The terminal block is used to connect alarm switches. Terminal assignment (starting at top left) Terminal Function Alarm 1 input Ground to input 1 Alarm 2 input Ground to input 2...

  • Page 126: Glossary

    ISDN JPEG kBit/s Local area network Appendix Installation and Operating Manual | VideoJet 8008 IEEE-802.3 specification for 10, 100 or 1000 MBit/s Ethernet Address Resolution Protocol: a protocol for mapping MAC and IP addresses Unit of measure for the speed of data transmission...
  • Page 127 VideoJet 8008 | Installation and Operating Manual MPEG-4 Net mask Parameters QCIF RFC 868 RS232/RS422/RS485 Standards for serial data transmission Subnet mask Telnet Wide area network Bosch Security Systems | 2005-06 | V2.0 Further development of MPEG-2, designed for transmission of audiovisual data at very low transfer rates (for example via the Internet).
  • Page 129 VideoJet 8008 | Installation and Operating Manual Protocols/standards Video standards Video encoding protocols Video data rate Image resolutions (PAL/NTSC) Total delay Image refresh rate Network protocols Bosch Security Systems | 2005-06 | V2.0 PAL, NTSC MPEG-4, JPEG 1 MBit/s ... 5 MBit/s per channel 704 ×...
  • Page 130 EN | 130 Installation and Operating Manual | VideoJet 8008 Appendix Bosch Security Systems | 2005-06 | V2.0...
  • Page 131 VideoJet 8008 | Installation and Operating Manual Index Activating a partition 38 Actuator 21 Alarm 49 Alarm input 14 Alarm message 64 Alarm recording 79 Alarm recording duration 41 Alarm sources 84 Alarm tracks 40 Assembly kit 18 Auto-connect 51...
  • Page 132 15 Heat 17 Identification 6 IGMP V2 54 Image quality 55 Image resolution 106 Image selection 103 Installation and Operating Manual | VideoJet 8008 Installation 8 Installation conditions 17 Installation location 17 Installation overview 19 Interface 14 Interface mode 57...
  • Page 133 VideoJet 8008 | Installation and Operating Manual Network 20 Network check 119 Network connection 22 Number of connections 28 Operation 7 Overview of functions 11 Parameters 25 Parity check 57 Partition 71 Partition name 43 Partitioning 71 Password 29 Password protection 46...
  • Page 134 TTL 55 Turn off 22 Turn on 22 Unicast 54 Unit date 47 Unit ID 45 Installation and Operating Manual | VideoJet 8008 Unit name 45 Unit overview 29 Unit time 47 Upload file 97 URL 28 User name 46...
  • Page 136 Bosch Sicherheitssyteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany www.bosch-sicherheitssysteme.de © 2005 Bosch Sicherheitssysteme GmbH Subject to change. Printed in Germany. 2908B/0605/en/2 Bosch Security Systems B.V. P.O. Box 80002 5600 JB Eindhoven The Netherlands www.boschsecuritysystems.com...

Table of Contents