Table of Contents
Advertisement
Other Functions
Control Using the TALLY/GPIO Connector
You can use control signals inputted to the TALLY/GPIO connector via GPI to remotely control the V-160HD from an external device.
Also, you can output tally signals or GPO control signals from the TALLY/GPIO connector.
Specification of the TALLY/GPIO Connector
Pin layout
13
12
11
10
9 8 7 6
25
24
23
22
21
20
19
DB-25 type (female)
Tally output
Trigger method
Open collector
Maximum input
12 V/120 mA
Control input
Trigger method
No-voltage contact (make-contact) triggering
Contact capacity DC 24 V 0.1 A or higher
Input method
Photocoupler
Pin assignments
Pin no.
Pin name
1
TALLY/GPO 1
2
TALLY/GPO 2
3
TALLY/GPO 3
4
TALLY/GPO 4
5
TALLY/GPO 5
6
TALLY/GPO 6
7
TALLY/GPO 7
8
TALLY/GPO 8
9
TALLY/GPO 9
10
TALLY/GPO 10
11
TALLY/GPO 11
12
TALLY/GPO 12
13
TALLY/GPO 13
14
TALLY/GPO 14
15
TALLY/GPO 15
16
TALLY/GPO 16
17
GND
18
GPI 1
19
GPI 2
20
GPI 3
21
GPI 4
22
GPI 5
23
GPI 6
24
GPI 7
25
GPI 8
70
5 4 3 2 1
18
17
16
15
14
Function
(default value)
PGM HDMI 1
PST HDMI 1
PGM HDMI 2
PST HDMI 2
PGM HDMI 3
PST HDMI 3
PGM HDMI 4
PST HDMI 4
PGM HDMI 5
PST HDMI 5
PGM HDMI 6
PST HDMI 6
PGM HDMI 7
PST HDMI 7
PGM HDMI 8
PST HDMI 8
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Inputting a Control Signal
When an external control signal is input, the functions assigned to
GPI 1–8 are executed.
Ó
1 .
[MENU] button
"RS-232/TALLY/GPO/GPI"
select GPI 1–8 "CATEGORY" and "VALUE," and press the
[VALUE] knob.
2 .
Use the [VALUE] knob to select the functions assigned to
GPI 1–8, and then press [VALUE].
ÁCATEGORY
Value
Explanation
N/A
No function is assigned.
PGM CH SELECT
Switches the PGM/A cross-point buttons.
PST CH SELECT
Switches the PST/B cross-point buttons.
AUX CH SELECT
Switches the video sent to the AUX bus.
INPUT 1–10 ASSIGN
Changes the video assigned to INPUT 1–10.
Pauses the normal output, and previews or
STILL OUTPUT
final outputs a cut of the still image.
PinP & KEY 1–4 SOURCE Switches the video source of the inset screen.
DSK 1, 2 SOURCE
Switches the DSK video source.
This works the same as when you press the
SW CONTROL
button selected in "VALUE. "
Switches the video between PGM/A bus
TAKE
and PST/B bus.
Turns the mute function on/off for the input
AUDIO INPUT MUTE
audio.
Turns the mute function on/off for the
AUDIO OUTPUT MUTE
output audio.
Turns the solo function on/off for the input
AUDIO INPUT SOLO
audio.
VOICE CHANGER SW
Turns the voice changer on/off.
Reverb turns on only while a control signal
REVERB (MOMENTARY)
is input.
REVERB (ALTERNATE)
Turns reverb on/off.
The final output video fades out to a black
OUTPUT FADE
screen.
LOAD MEMORY
Recalls a preset memory.
Each time a control signal is input, the
INPUT SCAN
INPUT 1–10 video changes in order.
Each time a control signal is input preset
MEMORY SCAN
memories 1–30 are recalled in order.
Executes a macro (a series of recorded
MACRO EXECUTE
operations).
When the sequencer function is on, this
SEQUENCER
works the same as when you press the button
selected in "VALUE. "
GPO (ONE SHOT)
Outputs a control signal for 0.5 seconds.
The control signal output is switched on/off
GPO (ALTERNATE)
each time a control signal is input.
ÁVALUE
Configures the detailed settings related to "CATEGORY. "
3 .
Press the [MENU] button to close the menu.
Ó
Ó
"GPI"
Hide quick links:
Advertisement
Table of Contents
