Page 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. The lightning flash with arrowhead symbol, within an CAUTION equilateral triangle, is intended to alert the user to the RISK OF ELECTRIC SHOCK presence of uninsulated “dangerous voltage”...
Page 3
INSTRUCTIONS IMPORTANTES DE SÉCURITÉ AVERTISSEMENT: Pour éviter les risques d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à l’humidité. L’éclair éché dans un triangle équilatéral est destiné à ATTENTION avertir l’utilisateur de la présence, dans l’appareil, d’une RISQUE DE CHOC ÉLECTRIQUE zone non-isolée soumise à...
Roland Service Center, or an authorized Secure a sufficient amount of space at the setup Otherwise, you risk injury as the result of Roland distributor, as listed on the “Information” when: the unit toppling over or dropping down. location • The power cord has been damaged; or This unit has internal fans for cooling.
Page 5
USING THE UNIT SAFELY CAUTION CAUTION Place in a well ventilated location Before cleaning the unit, disconnect the power plug from the outlet The unit should be located so that its location or position does not interfere with If the power plug is not removed from the its proper ventilation.
Sinon, vous risquez des blessures si facilement accessible. votre revendeur, le centre Roland le plus l’appareil se renverse ou tombe. proche ou un distributeur Roland agréé dont vous Ménager un espace suffisant à l’emplacement trouverez la liste dans les « Informations » lorsque : d’installation • Le cordon d’alimentation a été...
Page 7
CONSIGNES DE SÉCURITÉ ATTENTION ATTENTION Eteindre l’appareil avant d’installer l’interface Débrancher tous les cordons / câbles avant de d’extension déplacer l’appareil Avant d’installer l’interface d’extension, Avant de déplacer l’appareil, débranchez le vous devez d’abord toujours éteindre cordon d’alimentation de la prise et retirez tous les cordons des appareils externes.
• A small amount of heat will radiate from the unit • Roland, V-Mixer are either registered trademarks vicinity of this unit. Such noise could occur when or trademarks of Roland Corporation in the United during normal operation. receiving or initiating a call, or while conversing.
Turning the Power On and Off Installing an Expansion Interface (Option) Remote Control from an External Device Attaching the Rubber Feet Using a V-1200HDR Dedicated Controller Using V-1200HD RCS Dedicated Software Installation et Configuration RS-232 Connector Specifications Using the TALLY/GPIO Connector Remarques importantes concernant l’installation...
Refer to the figure below for the locations of the ventilation ports. Important Notes on Rack Mounting * When mounting the V-1200HD in a rack enclosure, pay attention to the following points to ensure efficient cooling. 5 Install in a well-ventilated location.
Reportez-vous à l’illustration ci-dessous pour les emplacements des ports de ventilation. Remarques importantes sur le montage en rack * Lors du montage du V-1200HD dans un rack, faites attention aux points suivants pour assurer un refroidissement efficace. 5 Installez dans un endroit bien ventilé.
(p. 4). Using an AC power outlet and an external power source at the * When turning off the power to the V-1200HD, first remove the same time is also possible. If either power source fails to supply USB flash drive from the USB port before you turn off the power.
(p. 6)). secours. Si l’une des sources d’alimentation ne parvient pas à * Lors de la mise hors tension du V-1200HD, retirez d’abord la clé fournir suffisamment de courant, le fonctionnement bascule USB du port USB avant la mise hors tension.
Attaching the Rubber Feet Attach the included rubber feet as required, such as using the V-1200HD without mounting it in a rack. Peel off the double-sided tape from the rubber feet and affix them at the locations shown in the figure.
5 Installez uniquement l’interface d’extension indiquée. Retirez Les interfaces d’extension de la série Xi optionnelles peuvent être uniquement les vis indiquées. installées dans les connecteurs d’extension du V-1200HD pour vous 5 Lors du redémarrage du V-1200HD avec une interface permettre d’augmenter les entrées et sorties disponibles.
This lights up when DC power is supplied from an external power unit connected to the rear panel. — AC indicator This lights up when AC power is supplied to the V-1200HD’s internal power supply circuit. — This turns the power to the V-1200HD on and off.
USB port — * This port is not active in the initial release of the V-1200HD. Use this port to connect an optional V-1200HDR dedicated controller, or a computer on which the V-1200HD RCS LAN port p. 27 remote-control software is installed.
Page 18
These are slots for installing optionally available Xi-series expansion interfaces. p. 14 (*1) For details about the multi-view screen, refer to the “V-1200HDR/V-1200HD RCS Remote Control Guide” (PDF) available for download from the Roland website. (*2) Settings must be made on the V-1200HD when inputting copyright-protected (HDCP) video. For details, refer to “About Copyright Protection...
HDCP required * The number of usable layers and AUXes varies according to the M/E settings and selections. You use a V-1200HDR or V-1200HD RCS remote- control software to make the settings. For details, refer to the “V-1200HDR/V-1200HD RCS Remote Control Guide” (PDF) available for download at the Roland website.
The V-1200HD’s 4:4:4 section supports copyright protection (HDCP). When all of the following conditions are satisfied, you can input an HDCP signal into the V-1200HD and output HDCP-applied video to the monitor. 5 The HDCP signal is input via either HDMI IN 3 or HDMI IN 4.
Connecting External Equipment You connect external equipment as shown in this chapter. For information on specific connection methods, refer to page 23 and after. Audio Input Video Input p. 24 p. 23 Computer, etc. CD player, audio mixer, etc. Video camera, etc. HDMI HDMI output connectors...
Page 22
If you are unsure of the connection method, AUDIO IN connector contact the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page. Unsuitable places for connection...
HDMI IN 3, 4 “About HDMI IN 3 and 4” (p. 20). 5 These support HDCP signal input. NOTE Settings must be made on the V-1200HD when inputting copyright-protected (HDCP) video. For details, refer to “About Copyright Protection (HDCP)” (p. 20). Memo...
AUDIO IN connector. Roland website. * Use an AES/EBU-compliant cable. https://proav.roland.com/manuals/ The V-1200HD supports the AES3 standard (24 bits, 48 kHz, two channels). Set the audio selector switch to [AES/EBU]. NOTE The audio selector switch affects both input and output. For...
5 STILL1, 2 (still images imported from a USB flash drive) * Connect a monitor that supports 1080/60p HDMI input. * The nominal output level of the V-1200HD is +4 dBu. Connect Here you connect a monitor for displaying input/output lists and menu screens.
Setup Menu You can display menus on a multi-view monitor connected to the V-1200HD and use them to make various settings. Using the Menus Menu operations follow the procedure described below. Connect a monitor to the HDMI OUT MULTI-VIEW 2 Select the target menu.
Remote Control from an External Device You can connect a remote-control device and use it to operate the V-1200HD. Using a V-1200HDR Dedicated Controller Using V-1200HD RCS Dedicated Software You can connect a V-1200HDR dedicated controller (optional) to the You can connect a computer on which the V-1200HD RCS LAN port and use it to operate the V-1200HD remotely.
Remote Control from an External Device Using the RS-232 Connector Using the TALLY/GPIO Connector You can use the RS-232 connector to operate the V-1200HD from a You can use the TALLY/GPIO connector to control the V-1200HD computer, touch panel, or other external control device.
Operating a VISCA-Compatible Video About the TALLY/GPIO Connector Camera by Remote Control The V-1200HD is equipped with a D-Sub 25-pin TALLY/GPIO connector. In addition to tally input/output functions, this provides functionality for control signal input and output, and you can use...
USB port. You can then recall the saved itself (MAIN) and for expansion interfaces (EXP A and EXP B) file from the USB flash drive to the V-1200HD for use when needed. connected at expansion slots A and B.
USB flash drives is not assured. Depending on the manufacturer and type of the USB flash drive, correct operation may not be possible. (*1) For detailed information on operation, refer to the “V-1200HDR/V-1200HD RCS Remote Control Guide” (PDF) available for download at the Roland website.
V-1200HDR Control Surface * Sold separately 482 (W) x 357 (D) x 133 (H) mm Remore Controler V-1200HD RCS * Windows7 SP1 or later, Mac OS X Dimensions 19 (W) x 14-1/16 (D) x 5-1/4 (H) inches AC 117 V, AC 220 V, AC 230 V, AC 240 V (50/60 Hz)
Appendix Block Diagram RE-ENTRY INPUT Video Block RE-ENTRY 422 PROCESS INPUT SDI 1 SDI 2 422 PROCESS SDI 1 SDI 3 2M/E SWITCHER 16 IN SDI 2 SDI 4 SDI 3 8 OUT 2M/E, 1.5M/E, 1M/E SDI 5 2M/E SWITCHER 16 IN SDI 4 SDI 6...
Page 35
Appendix OUTPUT PATCHBAY POST PROCESS PATCHBAY OUTPUT SDI 1 PATCHBAY POST PROCESS PATCHBAY SDI 2 SDI 1 16 IN 6 IN SDI 3 SDI 2 8 OUT 6 OUT SDI 4 16 IN 6 IN SDI 3 SDI 5 8 OUT 6 OUT SDI 4 CAPTURE...
Page 38
Roland Corporation 2036-1 Nakagawa, Hosoe-cho, Kita-ku, Hamamatsu, Shizuoka 431-1304, JAPAN Importer: Roland Europe Group Limited Hive 2, 1530 Arlington Business Park, Theale, Reading, Berkshire. RG7 4SA United Kingdom Warning: Operation of this equipment in a residential environment could cause radio interference.
Page 40
Roland Service Centers and Distributors Roland Service Centers and Distributors When you need repair service, access this URL and nd your nearest Roland Service Center or authorized Roland distributor in your country. https://roland.cm/proav_service *5100052732-03* Roland Service Centers and Distributors Roland Service Centers and Distributors...