Inspur Yingxin NP3020M2 Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Dear User of Inspur Yingxin Server,

Heartfelt thanks for your use of Inspur Yingxin Server!

This manual introduces the technical characteristics, the system instal-

lation and setup of the server to help you to fully understand and expediently

use this server.

Please deliver the package of our product to the waste recycling station

for recycling, in favor of pollution prevention and humankind's beneﬁ t.

This manual is the property of the Inspur Group Co., Ltd.

This User Manual is not to be copied by any group or person in any

manner without the consent of Inspur Group Co., Ltd. The Inspur Group

Co., Ltd. reserves the right of revising this manual momentarily.

Any alteration about the content of this manual will not be informed.

Please contact Inspur Group Co., Ltd. if you have any questions or ad-

vice about this manual.

"Inspur" is registered trademark of the Inspur Group Co., Ltd.

Other trademarks belong to other corresponding registered companies.

Inspur Group Co., Ltd.

August, 2011

Table of Contents

Need help?

Do you have a question about the Yingxin NP3020M2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Inspur Yingxin NP3020M2

Page 1 Co., Ltd. reserves the right of revising this manual momentarily. Any alteration about the content of this manual will not be informed. Please contact Inspur Group Co., Ltd. if you have any questions or ad- vice about this manual. Inspur Group Co., Ltd.
Page 2 5. Please read carefully our user manual before you use Inspur Yingxin server. 6. We must call your attention that in the application process you should pay attention to doing necessary backup of your ﬁ...
Page 3 9. The copyright of the marks and names of all the software and hardware prod- ucts involved in this manual is reserved by the relevant companies. 10. In the statements above, “us” indicates Inspur Group Co., Ltd; Inspur Group Co., Ltd. holds the right of ﬁ nal explanation about the above statements.
Page 4 In this chapter, solutions of some common problems are introduced. We suggest you read this manual seriously before you use this server for sake of the unnecessary faults in your operation. Address:No.1036 Langchao Road, Jinan City, China ( Inspur Group Co., Ltd.) Postcode:250101...
Page 5: Table Of Contents
4.2 Control Key Application ................20 4.3 SATA HostRaid Conﬁ guration ..............20 Chapter Five Operating System Installation ............24 5.1 Application Instructions for Inspur Driver U Disk ........25 5.2 Manually Install Windows Server 2003 Enterprise Edition .....29 5.3 Manually Install Windows Server 2008 Enterprise Edition .....34 5.4 Manually Install Red Hat Enterprise Linux 5.2 ........38...
Page 6: Chapter One Safety Information
Inspur; only maintenance technicians trained by Inspur have the right to disassemble the cover of the host, dismount and replace the internal components.
Page 7 Chapter One Security Information Warning 6: To avoid short circuit of internal components and ﬁ re or electric shock hazards, please do not ﬁ ll any object into the open pores of the system. Warning 7: Please place the system far away from the cooling plate and at the place with heat sources, and be sure not to block the air vents.
Page 8 - Close the cover of the host, re-connect the system to the power socket, and then start the equipment. - In case of operation failure or abnormal situation, please contact Inspur and get technical support. 3. Pay attention to the position of the system cables and power cables, wire them in places not to be stepped on or knocked down and ensure not to place other objectives on the cables.
Page 9 7. When dismounting the internal components with the approval of Inspur, please pay attention to the following matters: - Switch off the system power supply and disconnect the cables, including discon- necting any connection of the system.
Page 10 Chapter One Security Information to the following matters: - After the installation of cabinet is ﬁ nished, please ensure that the supporting feet have been ﬁ xed to the rack and supported to the ground, and all weight of the rack have been fell onto the ground.
Page 11: Chapter Two Product Description
Chapter Two Product Description Chapter Two Product Description 2.1 Server Technical Speciﬁ cation Processor Processor Type Intel Xeon E3-1200 or Intel Core i3-2100 series CPU Processor Count Processor Technology 32nm Processor Interface LGA1155 Sockets Chipset Chipset Type Intel® C202 chipset Memory Memory Type DDR3 1066MHz/1333MHz ECC Unbuffered memory...
Page 12 Standard conﬁ guration supports 5 pieces of SATA hard disks or up to Hard Disk Number 8 pieces of SATA/SAS hard disks through expansion accessories External Storage Drive Optional Inspur driver U disk, used to load hard disk controller Inspur Drive U Disk driver when installing the operating system manually CD-ROM (optional)
Page 13: Front Panel View
Chapter Two Product Description 2.2 Front Panel View Front Panel View Number Name Function and Introduction Power button Server on/off button Reset button System reset button Power indicator Always on when server works Display hard disk working condition, blinks Hard disk LED indicator when hard disk is reading and writing Always on: network is connected Network card 1st indicator light...
Page 14: Back Panel Introduction
Chapter Two Product Description 2.3 Back Panel Introduction 2.3.1 Back Panel View Back Panel View Number Name Function and Introduction Power interface Connect the host power line Power fan Power cooling fan I/O interface Input/output interface Chassis fan System cooling fan Expansion devices connecting PCI and PCI and PCI-E expansion slot PCI-E interfaces...
Page 15 Chapter Two Product Description Number Name Function and speciﬁ cation PS/2 mouse interface For connecting PS/2 mouse PS/2 keyboard interface For connecting PS/2 keyboard Rear USB interfaces 1, 2 For connecting USB interface devices Serial interface For connecting serial interface devices VGA interface For connecting display devices Integrated network card interface 1 Onboard gigabit network card interface 1...
Page 16: Chapter Three System Setup
Chapter Three System Setup Chapter Three System Setup In this chapter, the jumper of motherboard and BIOS function setup of this server are introduced. Only operator or administrator with qualiﬁ cation of system maintenance can implement these operations described in this part. 3.1 Motherboard BIOS Setup BIOS is a basic input and output system.
Page 17 Chapter Three System Setup 3.1.2 BIOS System Menu Introduction Next the following main function menus of BIOS are introduced. Menu Name Menu Function Conﬁ guring the basic system settings, such as system time, system Main date, super user and user password setup; displaying version of BIOS, CPU, and memory information etc Event Logs Conﬁ...
Page 18 Chapter Three System Setup 1. Main menu Entering BIOS setup utility, you can see Main menu displayed ﬁ rstly. Use the ar- row key to select the option, and press [Enter] to select submenu. ● BIOS Information Display BIOS’s version and modiﬁ cation time. ●...
Page 19 Chapter Three System Setup options. * Erase Event Log This option is used to set whether clear event logs or not, there are [No], [Yes, Next reset] and [Yes, Every reset] three options. * When Log is Full This option is used to set the approach when event logs are full, there are [Do nothing] and [Erase Immediately] two options.
Page 20 Chapter Three System Setup boot, then the setup can take effect. *Enhanced Intel SpeedStep Technology This item is used to set whether allow the operating system to dynamically regu- late CPU voltage and frequency in order to reduce system consumption and tempera- ture, including [Enabled] and [Disabled] two items.
Page 21 Chapter Three System Setup * Azalia HD Audio Turn on or off the audio controller including [Enabled] and [Disabled] two items. * INTEL W82574L OpROM1/2 Whether support the boot function conﬁ guration from the onboard network card 1/2 including [Disabled], [PXE], [iSCSI] three items. ●...
Page 22: Motherboard Jumper Settings
3.2.1 How to Open the Chassis Side Panel If the user need alter motherboard jumpers, please ﬁ rst obtain the authorization of Inspur Group Co., Ltd. Then open the chassis upper panel according to the following steps: 1. Power off the system (disconnect AC power cable).
Page 23 Chapter Three System Setup 3.2.2 Introduction of Motherboard Jumper Function Motherboard common use jumper location picture Jumper name Function description Jumper function Short-cutting pin1 and 2 to enable onboard Enable/disable onboard network controller 1 (default). Short-cutting LAN_SW1 network controller 1 pin2 and 3 to disable onboard network controller Short-cutting pin1 and 2 to enable onboard...
Page 24 Chapter Three System Setup Notes: 1. When clearing the CMOS, the system must be off and the power should be dis- connected. After short-cutting the CLRTC1 jumper’s Pin2-3, it needs to keep 5 seconds and then use jumper cap to short-cut the Pin1 and Pin2 of CLRTC1 jumper (default conﬁ...
Page 25: Chapter Four Sata Hostraid Setup
Chapter Four SATA HostRaid Setup Chapter Four SATA HostRaid Setup This chapter mainly introduces the conﬁ guration of onboard Intel SATA controller HostRaid and its application method. If the server you purchased does not use onboard SATA HostRaid, you can not refer to this chapter. If it does use onboard SATA HostRaid, please enter BIOS and set Advanced→SATA Conﬁ...
Page 26 Chapter Four SATA HostRaid Setup The executable menus of the conﬁ guration interface of SATA HostRaid are the following ﬁ ve: ● Create RAID Volume Create RAID Volume ● Delete RAID Volume Delete existing RAID Volume ● Reset Disks to Non-RAID Reset hard disks of RAID volume to Non-RAID ●...
Page 27 Chapter Four SATA HostRaid Setup Recovery: it allows two hard disks to create this RAID volume. RAID10: it allows four hard disks to create this RAID volume. RAID5 (Parity): it allows three and more than three hard disks to create this RAID volume.
Page 28 Chapter Four SATA HostRaid Setup The system will display all hard disks in RAID volume, so please select hard disks to be reset by [Space] based on actual demand, and then reset hard disk by press- ing [Enter]. The system will again warn whether there is a need to reset the hard disk, and enter Y or N according to the prompt.
Page 29: Chapter Five Operating System Installation
During manual setup of the operating system, some operating system may need the ﬂ oppy driver or Inspur driver U disk to load the drive of hard disk controller. Re- fer to the readme.pdf ﬁ le under the root directory in Inspur driver CD for the making method of the driver ﬂ...
Page 30: Application Instructions For Inspur Driver U Disk
U disk to load the drive of hard disk controller (at present, the operating sys- tems that use Inspur driver U disk to load the hard disk controller are Windows XP and above versions, Red Hat Linux 4.5 and above versions, Suse Linux 9.0 SP2 and above versions).
Page 31 Windows system shall be identiﬁ ed as A:, and only by this can the normal making of subsequent driver be guaranteed. 2. Put the driver CD (Inspur driver CD and RAID card driver CD) into the CD drive, and the driver making software will operate automatically. If the system forbids the automatic operation of CD, please enter CD directory and operate documents of dolphin.bat (Inspur driver CD) in CD or setup.exe (RAID card driver CD) in CD directory.
Page 32 Chapter Five Operating System Installation Input the navigation No. in the text box (the navigation No. is shown in CD box), click <OK> button, and it can log in the main interface of driver making software. Click <Cancel> button and exit the logging. (2) After inputting the navigation No.
Page 33 Inspur driver U disk, entering the interface of disk parti- tion, the Inspur driver U disk will occupy a disk letter. If the disk is not divided, U disk will occupy disk C:, and if the disk has other partitions, U disk will occupy other disk letter (please distinguish according to the actual hard disk partition).
Page 34: Manually Install Windows Server 2003 Enterprise Edition
Note: On making the above-mentioned drivers, please make the driver on the ﬂ oppy disk if using USB ﬂ oppy drivers, or make the driver on the Inspur driver U disks if using the Inspur driver U disk.
Page 35 Workstation/Server Express Chipset SATA RAID Controller”, and then press [Enter] to load the drive. If Inspur driver U disk is used (Please connect Inspur driver U disk before starting the system): Firstly, ensure that the corresponding drive has been made into the [3.5 Floppy disk (A:)] partition.
Page 36 Chapter Five Operating System Installation ◎ To create a new partition, enter its size below and press [Enter]. ◎ To go back to the previous screen without creating the partition, press [ESC]. The minimum size for the new partition is 8 megabytes <MB>. The maximum size for the new partition is XXX megabytes <MB>.
Page 37 Chapter Five Operating System Installation personal information you provided. Type your full name and the name of the company or organization. Name: Organization: The user can ﬁ ll in according to his actual situations and then click <Next> to continue the installation. 14.
Page 38 Chapter Five Operating System Installation (1) Insert the Inspur driver CD into CD-ROM, input the navigation No. on the driver CD set in the navigation No. veriﬁ cation interface popped up after the running of CD, click <OK> and it will enter the installation interface automatically;...
Page 39: Manually Install Windows Server 2008 Enterprise Edition
Note: On making the drivers, please make the driver into the ﬂ oppy disk if using USB ﬂ oppy drivers, or make the driver into the Inspur driver U disks if using the Ins- pur driver U disk.
Page 40 (2) When powering up and starting the installation of the operating system, con- nect the Inspur driver U disk to the USB interface on the server. (3) Please select <Load Driver> in the interface of “Where do you want to install Windows?”...
Page 41 “Server Manager”, select “Do not show this console at logon” and close the interface. 14. Install Chipset patch (1) Insert Inspur driver CD into CD-ROM, click the blue dolphin icon under the installation or operation procedure item in the automatically playing interface popped...
Page 42 CD and restart the system. 15. Install Network card driver (1) Insert Inspur driver CD into CD-ROM, click the blue dolphin icon under the installation or operation procedure item in the automatically playing interface popped out after the disk’s running, and input the navigation No. on the driver CD chassis in the navigation No.
Page 43: Manually Install Red Hat Enterprise Linux 5.2
Notes: On making the above-mentioned drivers, please make the driver into the ﬂ oppy disk if using USB ﬂ oppy drivers, or make the driver into the Inspur driver U disk if using the Inspur driver U disk.
Page 44 Chapter Five Operating System Installation gins to load ﬁ le and continues to install. 3. Installation program displays: CD Found Select <Skip> to evade the disk detection and press [Enter] to continue the instal- lation. 4. The installation program goes to “Red Hat Enterprise Linux 5” interface, so click <Next>...
Page 45 Chapter Five Operating System Installation 10. The installation program enters Boot Loader setting interface, so set as needed and click <Next> to continue the installation. 11. The installation program enters “Please click into the map to choose a region” interface, select “Asia/shanghai” and click <Next> to continue the installation. 12.
Page 46 <Finish> to ﬁ n- ish the installation. 28. Log in system. 5.4.3 Install Network Card Driver 1. Insert Inspur driver CD into CD-ROM, click Terminal menu in Applications→ Accessories, and input the following in the windows: #cd / #mount /dev/cdrom /mnt...
Page 47: Chapter Six Common Problems And Trouble-Shooting
Chapter Five Operating System Installation Chapter Six Common Problems and Trouble-shooting This chapter focuses on the common problems and Trouble-shooting of the server. If you are not sure about the cause of a failure and its removal method, please contact our customer service center for solution.
Page 48 ● If you are using the system CD to boot and install the operating system directly, the hard disk drive is generally added through the ﬂ oppy driver or Inspur driver U disk. When using USB ﬂ oppy driver to add the drive, please set the BIOS ﬁ rst and close the onboard ﬂ...
Page 49: Machine Alarm
Chapter Five Operating System Installation CD) and whether there is fault in the ﬂ oppy disk or Inspur driver U disk. 6.2.4 Instruction of Onboard SATA Controller If it is conﬁ gured onboard SATA HostRaid, it only supports windows system of above Windows XP versions and connects 6 SATA devices at most.
Page 50: Additional Notes
3. After having collected the basic information, please feedback the detailed alarm information to Inspur technical support personnel in a timely manner. We will make further analysis and judgment and help you solve the problem as soon as possible.
Page 51: Technical Support Information
ﬁ cial website of Inspur: http://www.inspur.com/support/Channel_Home/support_sv.asp 6.5 Technical Support Information If you have any doubt or unsolved problems in using Inspur server, please take the following measures: 1. If you have doubt in product conﬁ guration and speciﬁ cation details, please con- tact your supplier.

Inspur Yingxin NP3020M2 Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Inspur Yingxin NP3020M2

Summary of Contents for Inspur Yingxin NP3020M2

Table of Contents